• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.337-342
• /
• 1996

The pool-boiling critical heat flux (CHF) of water on small flat plates has been experimentally investigated focusing on the effects of the inclination angle and size of the heated surface under near atmospheric pressure. The second-phase experiment was accomplished to find out the general CHF behavior for over-all inclination angles from -90$^{\circ}$ to 90$^{\circ}$using two plate-type test sections (30$\times$150 mm and 40$\times$150 mm) submerged in a slightly subcooled water pool. Test results generally confirm the first-phase findings and show little effect of inclination angle for inclined upward-facing cases. CHF position moves to lower position with the increase of the heater characteristic size and inclination angle(from -30$^{\circ}$to 60$^{\circ}$).

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.05a
• /
• pp.173-179
• /
• 2001

The torsional or axial critical vibration of the order coinciding with the number of propeller blades is simultaneously excited by the harmonic tangential or radial forces acting on the crank shaft and by the harmonic of the same order from the propeller. The exciting torque of propeller is relatively small comparing with that of crank side, but the exciting force of propeller rather larger than that of crank shaft. With this situation, the exciting force of propeller cannot neglect if the axial vibration of propulsion shafting is calculated. With the propeller in its optimal angular position, i.e. its excitation effect opposed to that of the engine, the stresses at the critical revolution will largely cancel themselves out. In this paper, a method of optimizing the angular propeller position with regard to torsional and axial vibration is studied. The optimal relative angle is determined theoretically by calculation results of coupled torsional-axial vibration.

• Structural Engineering and Mechanics
• /
• v.4 no.1
• /
• pp.49-59
• /
• 1996

This paper considers large deflection problem of a simply supported beam with variable are length subjected to a point load. The beam has one of its ends hinged and at a fixed distance from this end propped by a frictionless support over which the beam can slide freely. This highly nonlinear flexural problem is solved by elliptic-integral method and shooting-optimization technique, thereby providing independent checks on the new solutions. Because the beam can slide freely over the frictionless support, there is a maximum or critical load which the beam can carry and it is dependent on the position of the load. Interestingly, two possible equilibrium configurations can be obtained for a given load magnitude which is less than the critical value. The maximum arc-length was found to be equal to about 2.19 times the fixed distance between the supports and this value is independent of the load position.

• Journal of Korean Critical Care Nursing
• /
• v.12 no.1
• /
• pp.13-21
• /
• 2019

Purpose : The aim of this study was to identify the factors influencing nursing performance in caring for patients with delirium. Methods: This study included 166 nurses who worked for more than 6 months at 4 general hospitals in Jeju Province, South Korea. Patients were administered a self-reported questionnaire. The study was carried out from May 20, 2014, to June 19, 2014. Data analyses were conducted using stepwise multiple regression, Pearson's correlation coefficients, t-test, and analysis of variance using the SAS WIN 9.2 program (SAS Institute, Cary, NC, USA). Results: The factors associated with nurses' performance in delirium care were work position (${\beta}=.22$, t=2.58, p <.001) and having received education on delirium care (${\beta}=.16$, t=2.24, p=.026). Conclusion: The results showed that the nurses' work position and having received education on delirium care affected nursing performance in delirium care. In order to improve nurses' performance in delirium care, hospitals should provide a delirium education program for nurses and establish standard guidelines on delirium care.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2012.06a
• /
• pp.80-81
• /
• 2012

Our society consist of many country's critical infrastructure such as production and distribution of electric power systems, communications technology, tele-communications, financial system, transportation systems when those systems are operated efficiently and normally. Country's critical infrastructure and its application fields of this magnitude rely on more and more P.N.T (Positioning, Navigation. Timing) systems, in which the tele-communications(Timing), financial market(Timing), logistics (Positioning, Navigation, Timing), transportation(Positioning, Navigation. Timing) is shoring. Reliability concerned about the exact position and timing of these critical national infrastructure rely on ability to provide a stable from GPS.

• Journal of the Institute of Convergence Signal Processing
• /
• v.2 no.4
• /
• pp.59-64
• /
• 2001

In this paper it was proposed method that solve problems of method to segment region of zero disparity and algorithm that extract binocular disparity to estimate position of object by vergence movement of moving stereo cameras experimented to compare those. There was not change of density value almost in region that change of critcal value was not found almost in image, because a high critical value was set so that critical value may be kipt changelessly about all small regions in studied treatise so far. The corresponding points were extracted wrongly by the result. By because the characteristics of small region was evaluated by autocorrelation and the critical value was established that may be proportional to the autocorrelation value, it was confirmed that corresponding points are not extracted almost by mistake and binocular disparity could by extracted with high speed.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.10
• /
• pp.140-147
• /
• 1998

The dynamic behavior of elastically restrained beams under the action of distributed tangential forces is investigated in this paper. The beam, which is fixed at one end, is assumed to rest on an intermediate spring support. The governing equations of motion are derived from the energy expressions, and the finite element formulation is employed to calculate the critical distributed tangential force. Jump phenomena for the critical distributed tangential force and instability types are presented for various spring stiffnesses and support positions. Stability maps are generated by performing parametric studies to show how the distributed tangential forces affect the frequencies and the stability of the system considered. Through the numerical simulations, the following conclusioils are obtained: (i) Only flutter type instability exists for the dimensionless spring stiffness K $\leq$ 97, regardless of the position of the spring support. (ii) For the dimensionless spring stiffness K $\leq$ 98, the transition from flutter to divergence occurs at a certain position of the spring support, and the transition position moves from the free end to the free end of the beam as the spring stiffness increases. (iii) For K $\leq$ 10$^{6}$ the support condition can be regarded as a rigid support condition.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1999.10a
• /
• pp.190-190
• /
• 1999

CHF (Critical heat flux) on the external surface of the reactor vessel lower head is major key in the evaluation on the feasibility of IVR-EVC (In-Vessel Retention through External Vessel Cooling) concept. To identify the CHF on the external surface, considerable works have been performed. Through the review on the previous works related to the CHF on the external surface, liquid subcooling, induced flow along the external surface, ICI (In-Core Instrument) nozzle and minimum gap are identified as major parameters. According to the present analysis, the effects of the ICI nozzle and minimum gap on CHF are pronounced at the upstream of test vessel: on the other hand, the induced flow considerably affects the CHF at downstream of test vessel. In addition, the subcooling effect is shown at all of test vessel, and decreases with the increase in the elevation of test vessel. In the real application of the IVR-EVC concept, vertical position is known as a limiting position, at which thermal margin is the minimum. So, it is very important to precisely predict the CHF at vertical position in a viewpoint of gaining more thermal margins. However, the effects of the liquid subcooling and induced flow do not seem to be adequately included in the CHF correlations suggested by previous works, especially at the downstream positions.

• Geomechanics and Engineering
• /
• v.16 no.4
• /
• pp.415-421
• /
• 2018

A location determining method is proposed for critical sliding surface in the stability analysis of the filling materials in karst caves. First, a preliminary location of the sliding surface is determined based on simulation results which includes displacement contour and plastic zone. The sliding surface will locate on the bottom contact interface when the friction angle is relative small. However, a weakened contact interface always becomes the critical sliding surface no matter what the friction angle is. Then when the friction angle becomes larger, the critical sliding surface inside fillings can be determined by a parabola, the coefficient of which increases linearly with the friction angle under the same cohesion. Finally, the critical sliding surface approximately remains unchanged with friction angle. The influence of cohesion is similar to that of friction angle. Although affected by shape, size or position of the karst cave, the critical sliding surface mainly depends on both friction angle and cohesion. Thus, this method is always useful in determining the critical sliding surface.

• Journal of Microbiology and Biotechnology
• /
• v.25 no.10
• /
• pp.1634-1639
• /
• 2015

Cytochrome P450 hydroxylase (CYP) in actinomycetes plays an important role in the biosynthesis and bioconversion of various secondary metabolites. Two unique CYPs named CYP-sb21 and CYP-pa1, which were identified from Sebekia benihana and Pseudonocardia autotrophica, respectively, were proven to transfer a hydroxyl group at the 4^th or 9^th N-methyl leucine position of immunosuppressive agent cyclosporin A (CsA). Interestingly, these two homologous CYPs showed different CsA regio-selectivities. CYP-sb21 exhibited preferential hydroxylation activity at the 4^th position over the 9^th position, whereas CYP-pa1 showed the opposite preference. To narrow down the CYP domain critical for CsA regio-selectivity, each CYP was divided into four domains, and each domain was swapped with its counterpart from the other CYP. A total of 18 hybrid CYPs were then individually tested for CsA regio-selectivity. Although most of the hybrid CYPs failed to exhibit a significant change in regio-selectivity in the context of CsA hydroxylation, hybrid CYP-pa1 swapped with the second domain of CYP-sb21 showed a higher preference for the 9^th position. Moreover, hybrid CYPsb21 containing seven amino acids from the 2nd domain of CYP-pa1 showed higher preference for the 4^th position. These results imply that the 2nd domain of CsA-specific CYP plays a critical role in CsA regio-selectivity, thereby setting the stage for biotechnological application of CsA regio-selective hydroxylation.