• 한국자동차공학회논문집
• /
• 제7권6호
• /
• pp.42-48
• /
• 1999

Engine misfire causes of the negative effect on exhaust emission such as HC, CO, and NOX . Moreover, it causes damage to the three-way-catalyst(TWC) system permanently. The crankshaft velocity fluctuation(CVF) method has been applied for the real cars as misfire detection system usually, which utilizes the crank angle sensor input to calculate the variation of the crankshaft rotational speed. But this approach has the limit due to the fact that three could be problem under certain engine condition like as deceleration or high speed condition . Therefore the development of new methods are requested today. This study introduced the new method of misfire detection using breakdown voltage(BDV) characteristics between spark plug electrouds.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 하계종합학술대회논문집
• /
• pp.235-238
• /
• 1998

This paper presents the detection of internal combustion engine's multiple misfire. The primary cause of air pollution by vehicles is imperfect conbustion of fuel. The CARB(California Air Resources Board) have imposed regulations for the detection of misfiring in automotive engines. The OBD-II regulations requir that misfire should be monitored by the diagnostic system, and that the goal of OBD-II is to alert the driver to the presence of a malfunction of the emission control system. Present invention based upon measurements of engine roughness as derived from crankshaft angular velocity measurements with special signal processing method. Crankshaft angular velocity signals are processed by walsh-fourier transform. Experimental work confims that it's possible to apply walsh-fourier transform for the detection of multiple misfires in no-load idle and road testing.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2006년도 전기학술대회논문집
• /
• pp.83-84
• /
• 2006

크랭크 샤프트 디플렉션 측정은 선박엔진의 조립공정에 있어, 크랭크 샤프트를 조립 시 1회전의 상태에서 크랭크 스루 간의 디플렉션 상대값의 변화를 확인하는 것이다. 이를 통하여 크랭크 샤프트가 정상 조립되었는지 확인할 수 있다. 기 개발 완료한 구형 무선 크랭크 샤프트 디플렉션 측정장치(상품명 : Measutal)는 측정장치의 길이로 인해 선박용 엔진 중 저속 엔진에만 적용 가능하였다. 하지만 중속엔진의 경우 공간이 협소하여 크랭크 샤프트 디플렉션 측정이 어려우며, 이는 폭정 오차를 수반하게 된다. 본 논문은 상기 문제를 해결하기 위해 중속에도 적용 가능한 신 모델의 개발에 관한 것이다. 또한 개발된 신 모델은 소비자의 요구를 만족하기 위해 구 모델에 비하여 밧데리 지속시간 향상되었고 무선 통신 거리가 확대되었다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.107-110
• /
• 1999

The purpose of this research is for the development of a new type forging equipment H.C.G(Hyundai Continuous Grain-flow) by using two virtual build-up tools rigid viscoplastic FEM and downsized plasticine experiment. This forging equipment consists of consecutive horizontal and vertical pressure while the traditional forging method consists of only vertical pressure. Using this method high quality crankshafts can be forged as it can maintain a continuous grain flow. The factors considered in the development of equipment are die geometry for flawless deformed shape die reaction forces stress/strain distributions and continuous material flow. We carried out several numerical simulations and downsized plasticine experiments for the proper design of the forging equipment. The validity of those simulation results is confirmed by checking with the actual test results. Based on these simulation results the proper design of the H.C.G for ging equipment is enabled.

• Tribology and Lubricants
• /
• 제12권2호
• /
• pp.8-19
• /
• 1996

Scroll compressor using a slide bushing type radial compliant crank mechanism is modelled, and it's dynamic behaviour characteristics are analyzed. Sealing forces generated in the flank surfaces of the orbiting scroll depending on the distance, e, from slide bushing center to crank pin center are calculated. From the stable condition of orbiting scroll for the moment equilibrium in tangential direction, the range of e is determined as 0$r_o$. Transient response of a crankshaft supported by two journal bearings is investigated, considering applied load, moment, and unbalance force by eccentric mass. As a result, conical whirl mode with circular orbits are obtained. The characteristics of journal orbits and frictional losses are calculated with a variation of viscosity and bearing clearance.

• Tribology and Lubricants
• /
• 제12권2호
• /
• pp.20-31
• /
• 1996

Pressures in compression pockets consists of two identical spiral scrolls are influenced by gas flow resistance in discharge process and leakages in radial and tangential directions between two scroll wraps. In this paper, considering geometrical characteristics of these members, flow resistance and refrigerant gas leakage losses, pressure variations in compression pockets are calculated. For a scroll compressor model with fixed crank mechanism, acting load on crankshaft is analyzed. And, for a vertical type crankshaft-journal bearing system used in scroll compressor, nonlinear transient response is calculated including nonlinear fluid film reaction forces of journal bearings.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.453-457
• /
• 2006

This study predicts the modified structure of eigenvectors and eigenvalues due to the changes in the mass and the stiffness of the structure. The sensitivity method of natural frequency using partial differential are derived with respect to the physical parameter to calculate the structure modification. The method are applied to the 3 degree of freedom???slumped mass model by modeling the mass and stiffness, and then applies the method to a real crankshaft system. The position, direction of parameter change and modified value were predicted for modification. Finally the predicted value is used to investigate the magnitude of vibration and we found that the effect of modification results to reduce the level of magnitude vibration is satisfactory.

• The Journal of the Acoustical Society of Korea
• /
• 제18권4E호
• /
• pp.20-25
• /
• 1999

To get accurate natural frequencies of an engine crankshafts, finite element equations of motion are developed, taking real geometries of the shaft into account. For the crankshaft with wide crank webs, a specialized rotating web element is developed. This includes the effects of rotary inertia, gyroscopic moment, and shear. After the finite element equations are constructed, eigenvalues are extracted from the system equations to get natural frequencies, based on the Sturm sequence method which exploits the banded forms of the system matrices to reduce computations. The scheme developed can be used for the free vibration analysis of any type of spinning structures which include skew symmetric gyroscopic moment matrix in the system matrices. The results are compared with experimental data in order to confirm the study.

• 한국자동차공학회논문집
• /
• 제12권6호
• /
• pp.90-95
• /
• 2004

In this study, for the crankshaft bearing design adapting discontinuous oil supply system, analyses were conducted to determine the lubrication characteristics such as oil flow rate and increase of oil temperature at main bearing and connecting rod bearing. Additionally, supplied oil pressure and temperature effects on the bearings were simulated to figure out lubrication characteristics on the bearings. Finally the effects of increasing the bearing width and clearance were introduced on the lubrication characteristics.

• Journal of Advanced Marine Engineering and Technology
• /
• 제12권1호
• /
• pp.28-36
• /
• 1988

Since the oil shocks of 1970s, the quality of the fuel oil for marine diesel engines has become more degarded than ever. When the poorer quality fuel is burned, carbon residues of the fuel oil cause blockage of the fuel injection valve nozzle and troubles of fuel injection system. The mis-firing of engine occurs due to the decrease of fuel quantity injected, the decrease of compression pressure in the slow speed range, the increase of fuel leaked and the high ignition temperature of degraded fuel etc. This paper is to investigate theoretically the effects of mis-firing on the crankshaft axial vibration of diesel engine. The cylinder pressure in operation is calculated by the computer aided simulation of closed cycle for a large two-stroke diesel engine and also the exciting force of axial vibration and the resonance amplitudes are calculated. And then, the condition of normal state, misfiring and one-cylinder cut-off operation are analyzed. The results of calculations show good agreements with those of the actual measurements.