• Journal of the Korean Chemical Society
• /
• v.58 no.3
• /
• pp.283-288
• /
• 2014

A column solid phase extraction procedure based on modified polyurethane foam (PUF) by a newly synthesized Schiff base ionophore, named 2,2'-{iminobis[propane-3,1-diylnitrilo(1E)prop-1-yl-1-ylidene]}diphenol, was developed for preconcentration step of trace amounts determination of copper ions in water samples by atomic absorption flame spectroscopy. The influence of parameters on the adsorption process such as sample pH, amount of modified PUF packed in the column, type and volume of stripping reagent and its flow rate were investigated and optimized. Under optimum experimental conditions, the calibration graph was linear in a relatively wide range ($0.005-210{\mu}g/ml$) with a limit of detection $0.002{\mu}g/ml$ of copper. The proposed method allows achieving to a concentration factor of >133. The capacity of a column (1.6 cm i.d.) packed by 6 g of PUF modified by 12 mg of the Schiff base was found to be $247.7({\pm}2.1){\mu}g$ of copper. It was found that the adsorption process was highly selective towards copper ions with respect to some associated metal ions. The presented procedure was successfully applied for determination of copper in some water samples.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.5
• /
• pp.243-248
• /
• 2017

In this study copper glaze samples were prepared with varying amount of tin oxide, and the chromatic characteristics of glazes were explained on the results of spectrophotometric, crystalline phase, and microstructural analyses. The red color of copper glaze was dissipated with the addition of tin oxide and turned into achromatic color due to the decrease of CIEab values. Tin oxide homogeneously distributed in the glaze layer interfered with the red color generation coming from the growth of Cu nuclei, and formed an alloy with metal copper around bubbles. This resulted in the decrease of metal copper peak intensity with minor $Cu_2O$ peak. With the 3.79 % tin oxide addition the glaze was appeared as gray due to the black color CuO and Cassiterite $SnO_2$ phases.

• Journal of Environmental Science International
• /
• v.19 no.9
• /
• pp.1177-1185
• /
• 2010

To examine the potency of biosorbent, the adsorption capacity of Pseudomonas cepacia H42 isolated from fresh water plant root was compared with Saccharomyces cerevisiae SEY2102 on bases of biomass, concentration of heavy metal, presence of light metals, immobilized cell, and ion exchange resin. P. cepacia H42 biomass of 0.05-0.5 g/L increased adsorption and above 1.0 g/L of yeast biomass was the most effective in adsorption. By applying the same amount of biomass, lead showed the highest adsorption on two strains and the adsorption strength was lead>copper>cadmium on both strains. The high heavy metal concentration induced the high adsorption capacity. P. cepacia H42 adsorption was in the order of copper>lead>cadmium and lead>copper>cadmium by yeast in 10 mg/L. Both strain showed same adsorption strength in the order of lead>copper>cadmium in 100 mg/L and 1000 mg/L. The adsorption capacity of both yeast and P. cepacia H42 was decreased in the presence of light metals and the order of cadmium>copper>lead. $Mg^{2+}$ induced the least adsorption while $Na^+$ induced highest adsorption. The adsorption capacity of immobilized yeast and P. cepacia H42 was detected between 200-400 mL in flow volume and decreased in the presence of light metals. Ion exchange containing light metals caused 30-50% adsorption reduction on both strains.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• v.5 no.2
• /
• pp.206-211
• /
• 2002

Wilson's disease is a treatable autosomal recessive inherited disorder of copper metabolism due to mutation of the copper transporting gene. The basic strategy of treatment is to reduce the amount of copper in the liver and other tissues by administering both a low copper diet and copper-chelating agents. D-penicillamine is the first choice as a copper-chelating agent. Some serious side effects could occur in 3~5% of all patients following D-penicillamine therapy. We report a 19 year-old male with Wilson's disease who developed nephrotic syndrome 6 months after the initiation of D-penicillamine therapy. Prednisolone was administered to control nephrotic syndrome and D-penicillamine was switched to trientine. Urinary remission was achieved within a week and maintained thereafter. Nephrotic syndrome was proven to be MCNS by kidney biopsy.

• Research in Plant Disease
• /
• v.14 no.2
• /
• pp.102-106
• /
• 2008

The single application of Bacillus subtilis QST713(BS QST713) mixed application with fungicides and alternate application were treated to examine the control of alternaria leaf blight of Panax ginseng. Control value of alternaria leaf blight by single application of BS QST713 at 10 days interval was 83.3%, and those of single application at 10 days interval was $80.4{\sim}83.7%$ by azoxystrobin, chlorothalonil copper sulfate basic, copper sulfate basic, kresoxim-methyl, difenoconazole, mancozeb. When mixture of BS QST713 and fungicides were applied at 14 days interval, the control value of alternaria leaf blight were 83.6% by BS QST713 and mancozeb, and 82.6% by BS QST713 and azoxystrobin. However, mixture of BS QST713 with difenoconazole, kresoxim-methyl, copper sulfate basic and chlorothalonil copper sulfate basic exhibited the disease control values from 61.1% to 76.4%, which showed slightly lower control efficacy. In Daejeon, the alternate application of BS QST713 followed by copper sulfate basic with 14 days interval was 85.9% in control value, which showed the best control efficacy. The alternate application with other tested fungicides slightly decreased to $55.5{\sim}78.2%$ in control value. However, the alternate application of BS QST713 followed by fungicides showed very high control efficacy, which were approximately 90% in Muju, Jeonbuk Province. Consequently, the single, mixed or alternate application of BS QST713 and fungicides could be recommended as a control method to reduce the amount of fungicides.

• Journal of the Korean Geosynthetics Society
• /
• v.13 no.2
• /
• pp.59-67
• /
• 2014

The amount of the contaminants that can be adsorbed on the drain was evaluated for the effective remediation of the contaminated soil, and the contaminants adsorptivity of the drain was evaluated by comparing the isothermal adsorption model after carrying out the contaminants adsorption test of the reactants coated on the surface of the drain. The reactant used in the experiment is a natural zeolite, and the contaminants are copper, lead and cadmium. The results that Freundlich and Langmuir adsorption isotherm model are compared to the adsorption amount according to the change of the initial concentration by the contaminants. As a result of the component analysis, because Si, Al and O are contained approximately 28%, 11% and 48%, respectively, it is identified that the material coated on the surface of the drain is the component of the zeolite which is the reactant for the adsorption of the heavy-metal (Cu, Pb, Cd) contaminants. The heavy-metal adsorption kinetic of the zeolite which is the reactant was decreased in order of lead, copper and cadmium. The important factor of the performance evaluation of the adsorbent is the reaction rate, and if zeolite is used as the reactant in the relationship between the maximum amount of adsorption and reaction rate, it can be utilized as the design factor that determine the removal order of the complex heavy-metal. In other words, because the maximum adsorption quantity of lead is smaller compared to copper but the reaction rate is relatively fast, it can be primarily removed, and copper can be removed after removing the lead. It was analyzed that Cadmium can be finally removed after that other heavy-metal is removed.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.1
• /
• pp.42-47
• /
• 2010

Polymer insulating materials such as cross linked polyethylene (XLPE) are employed in electric cables used for extra high voltage. These materials can degrade due to chemical, mechanical and electric stress, possibly caused by voids, the presence of extrinsic materials and protrusions. Therefore, this study measured discharge patterns, discharge phase angle, quantity and occurrence frequency as well as changes in XLPE under different temperatures and applied voltages. To quantitatively analyze the irregular partial discharge patterns measured, the discharge patterns were examined using a statistical program. A three layer sample was fabricated, wherein the upper and lower layers were composed of non-void XLPE, while the middle layer was composed of an air void and copper particles. After heating to room temperature and $50^{\circ}C$ and $80^{\circ}C$ in silicone oil, partial discharge characteristics were studied by increasing the voltage from the inception voltage to the breakdown voltage. Partial discharge statistical analysis showed that when the K-means clustering was carried out at 9 kV to determine the void discharge characteristics, the amount discharged at low temperatures was small but when the temperature was increased to $80^{\circ}C$, the discharge amount increased to be 5.7 times more than that at room temperature because electric charge injection became easier. An analysis of the kurtosis and the skewness confirmed that positive and negative polarity had counterclockwise and clockwise clustering distribution, respectively. When 5 kV was applied to copper particles, the K-means was conducted as the temperature changed from $50^{\circ}C$ to $80^{\circ}C$. The amount of charge at a positive polarity increased 20.3% and the amount of charge at a negative polarity increased 54.9%. The clustering distribution of a positive polarity and negative polarity showed a straight line in the kurtosis and skewness analyses.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1288-1291
• /
• 2004

In this study, physical characteristics of alumina slurry on variation of pH value and the effect of non-ionic surfactants on alumina slurry for copper chemical mechanical planarization (CMP) slurry have been investigated. After pH value of the slurry with alumina abrasive was changed by adding various amount of $HNO^3$ or KOH, the differences of settling rate, particle size, and zeta-potential were estimated. Better settling rates were shown in slurries with alumina abrasive at near pH 1. Higher zeta-potential was shown at around pH 2 in alumina slurry and the point of zero charge (PZC) was measured at about pH $9\sim10$. Non-ionic surfactant was added in the slurry with 5wt% alumina abrasive to get its effect on slurry practically. Abrasive size was smaller increased when amount of surfactant increased in slurry with P-4 as abrasive; on the other side, it was smaller when amount of surfactant decreased with AES-12. Variation of zeta-potential has no tendency with adding surfactant; however, values of zeta-potential were between $35\sim50mV$. The proper amount of surfactant was $0.1\sim1.0wt%$ in slurry with P-4 and $0.5\sim1.0wt%$ in slurry with AES-12 respectively. Excellent dispersion stabilization was obtained by addition of non-ionic surfactant

• Resources Recycling
• /
• v.23 no.3
• /
• pp.30-36
• /
• 2014

A large amount of waste copper slag containing about 35 ~ 45% iron has been generated and discarded every year from pyrometallurgical processes for producing copper from copper concentrate. Thus, recovery of iron from the waste copper slag is of great interest for comprehensive use of mineral resource and reduction of environment problems. In this study, a physico-chemical separation process for upgrading iron from the waste copper slag discharged as an industrial waste has been developed. The process first crushes the waste copper slag below 1 mm (first crushing step), followed by carbon reduction at $1225^{\circ}C$ for 90 min (carbon reduction step). And then, resulting material is again crushed to $-104{\mu}m$ (second crushing step), followed by wet magnetic separation (wet magnetic separation step). Using the developed process, a magnetic product containing more than 66 wt.% iron was obtained from the magnetic separation under a magnetic field strength of 0.2 T for the waste copper slag treated by the reduction reaction. At the same conditions, the percentage recovery of iron was over 72%. The iron rich magnetic product obtained should be used as a iron resource for making pig iron.

• Journal of the Korean Ceramic Society
• /
• v.52 no.4
• /
• pp.264-268
• /
• 2015

Cu films were plated in an eco-friendly electroless bath (No-Formaldehyde) on Ni/screen printed Ag pattern/PET substrate. For electroless Cu plating, we used sodium-phosphinate ($NaH_2PO_2{\cdot}H_2O$) as reducing agent instead of Formaldehyde. All processes were carried out in electroless solution of pH 7 to minimize damage to the PET substrate. According to the increase of sodium-phosphinate, the deposition rate, the granule size, and rms roughness of the electroless Cu film increased and the Ni content also increased. The electroless Cu films plated using 0.280 M and 0.575 M solutions of sodium-phosphinate were made with Cu of 94 at.% and 82 at.%, respectively, with Ni and a small amount P. All electroless Cu plated films had typical FCC crystal structures, although the amount of co-deposited Ni changed according to the variation of the sodium-phosphinate contents. From these results, we concluded that a formation of higher purity Cu film without surface damage to the PET is possible by use of sodium-phosphinate at pH 7.