• Journal of electromagnetic engineering and science
• /
• v.16 no.1
• /
• pp.7-12
• /
• 2016

This paper presents the design of a negative group delay circuit (NGDC) using the filter synthesis approach. The proposed design method is based on a frequency transformation from a low-pass filter (LPF) to a bandstop filter (BSF). The predefined negative group delay (NGD) can be obtained by inserting resistors into resonators. To implement a circuit with a distributed transmission line, a circuit conversion technique is employed. Both theoretical and experimental results are provided for validating of the proposed approach. For NGD bandwidth and magnitude flatness enhancements, two second-order NGDCs with slightly different center frequencies are cascaded. In the experiment, group delay of $5.9{\pm}0.5ns$ and insertion loss of $39.95{\pm}0.5dB$ are obtained in the frequency range of 1.935-2.001 GHz.

• Journal of the Korean Magnetics Society
• /
• v.20 no.1
• /
• pp.28-33
• /
• 2010

The purpose of this paper is to analyze and design a new hybrid electromagnetic linear actuator for linear pumps. Solenoid linear actuator is widely used because it occupies small space due to no mechanical energy conversion system. In addition, the energy loss is very low and it has no noise. Conventional solenoid linear actuator, however, has the critical drawback of high power consumption. In this research, we present a new hybrid electromagnetic linear actuator using a permanent magnet in order to reduce power consumption. The enhanced performance of the hybrid linear actuator was verified by dynamic finite element analysis.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.8
• /
• pp.1311-1316
• /
• 2007

To develop photo-sensitizers for dye-sensitized solar cells (DSCs) used in harvesting sunlight and transferring solar energy into electricity, we synthesize novel Ru(II) polypyridyl dyes and describe their characterization. We also investigate the photo-electrochemical properties of DSCs using these sensitizers. New dyes contain chromophore unit of dafo (4,5-diazafluoren-9-one) or phen-dione (1,10-phenanthroline-5,6-dione) instead of the nonchromophoric donor unit of thiocyanato ligand in cis-[RuII(dcbpy)2(NCS)2] (dcbpy = 4,4'-dicarboxy- 2,2'-bipyridine) coded as N3 dye. For example, the photovoltaic data of DSCs using [RuII(dcbpy)2(dafo)](CN)2 as a sensitizer show 6.85 mA/cm2, 0.70 V, 0.58 and 2.82% in short-circuit current (Jsc ), open-circuit voltage (Voc), fill factor (FF) and power conversion efficiency (Eff), which can be compared with those of 7.90 mA/ cm2, 0.70 V, 0.53 and 3.03% for N3 dye. With the same chelating ligand directly bonded to the Ru metal in the complex, the CN ligand increases the Jsc value by double, compared to the SCN ligand. The extra binding ability in these new dyes makes them more resistant against ligand loss and photo-induced isomerization within octahedral geometry.

• Journal of the Optical Society of Korea
• /
• v.16 no.2
• /
• pp.151-156
• /
• 2012

Reflective polarizers can be used as luminance enhancement films for LCD backlights via the polarization recycling process. The optical performances of a wire grid polarizer (WGP) as a reflective polarizer adopted in edge-lit backlights were investigated by luminance evaluation and a time-domain simulation technique. The results were compared to those of a commercial dielectric multilayer film. The luminance gain factor of WGP was smaller than that of the multilayer film by 18%. This was attributed to a much larger internal loss of WGP due to light absorption by metal wires. The internal losses of both reflective polarizers and the polarization conversion efficiency of the backlight were obtained numerically based on a phenomenological model. The optical performances of WGP were optimized by using a time-domain simulation technique. The luminance gain increased and was found to become comparable to, but slightly less than the case of the dielectric multilayer film with decreasing line width.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.3
• /
• pp.40-51
• /
• 2008

This research presents a new active auxiliary resonant snubber with for induction heating PWM high frequency inverter solving the problem of induction heating PWM high frequency inverter circuit which is using widely in the practical application of an induction heating apparatus, the soft switching operation and power control are impossible when the lowest power supply in the active auxiliary resonant snubber with for induction heating PWM high frequency inverter. The inverter circuit which is attempted by the on-off operation of a switch has the effect of reducing the power loss due to soft switching and high frequency switching. This confirms that power regulation is possible on a continuous basis from 0.25[kW] to 2.84[kW] where the duty factor(D) changes from 0.08 to 0.3 under zero current switching which operates by an asymmetrical pulse width modulating control. The power conversion efficiency is 95[%]. Due to these results, the active auxiliary resonant snubber for an induction heating PWM high frequency inverter is considered effective as a source of induction heating.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.10a
• /
• pp.241-243
• /
• 2008

This research presented the new zero-current switching pulse width modulation SEPP(Single Ended Push-Full)high frequency inverter for solving the problem of the zero-current SEPP high frequency inverter circuit which is using widely in the practical application of an induction heating apparatus, the soft switching operation and power control are impossible when the lowest power supply in the zero-current switching pulse width modulation SEPP high frequency inverter. The inverter circuit which is attempted by on-off operation of a switch has the reduction effect of the power loss due to a soft switching and a high frequency switching. And it confirmed that the power regulation is possible continuously from 0.25[kW] until 2.84[kW] in the case the duty rate(D) changes from 0.08 to 0.3 under zero-current switching operating by a dissymmetry pulse width modulating control and the power conversion efficiency comes true the efficiency of 95[%]. Due to the result above, the ZCS PWM SEPP high frequency inverter will be effective as sources of an induction heating apparatus.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2898-2903
• /
• 2008

The coal considerably is the energy resource which is important with the new remarking energy resource. The coal conversion has two processes which are coal devolatilization and char oxidation. Coal devolatilization is important because it describes up to 70% weight loss and has been shown that nitrogen contribute 60 to 80% of the total NOx produced. The chemical percolation devolatilization(CPD) model is used here to describe coal devolatilization. The model was developed to describe coal devolatilization behavior of rapidly heated coal based on characteristics of the chemical structure of the parent coal. This paper describes CPD model in detail and makes an analysis of Shenhua coal(bituminous) which is used calculated 13-C NMR(carbon-nuclear magnetic resonance).

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2221-2226
• /
• 2008

The objective of this paper is to describe the experimental and numerical investigation of the analysis of the heat transfer in a solar chemical reactor. These are compared about methane steam reforming process in the solar chemical reactor which was a volumetric absorber consisting of honeycomb and a multilayered catalyst supports. With this high operating temperature, convective heat loss, thermal fracture are important features for designing SCR. In order to estimate the system performance and to design the actual solar reactor with various conditions, CFD analysis was used in this study. The nickel oxide porous metal is inserted inside the solar chemical reactor to increase the conversion rate of the reforming reaction. Simulation has been carried out based on the experimental data. According to the simulation results, the optimum methane-steam mole ratio and thickness and numbers of catalyst supports were obtained.

• Journal of IKEEE
• /
• v.17 no.2
• /
• pp.176-181
• /
• 2013

This paper presents a CMOS impulse radio ultra-wideband (IR-UWB) receiver implemented using IBM 0.13um CMOS technology for inner/inter-chip wireless interconnection. The IR-UWB receiver is based on the non-coherent architecture which removes the complexity of RF architecture (such as DLL or PLL) and reduces power consumption. The receiver consists of three blocks: a low noise amplifier (LNA) with active balun, a correlator, and a comparator. Simulation results show the die area of the IR-UWB receiver of 0.2mm2, a power gain (S21) of 12.5dB, a noise figure (NF) of 3.05dB, an input return loss (S11) of less than -16.5dB, a conversion gain of 18dB, a NFDSB of 22. The receiver exhibits a third order intercept point (IIP3) of -1.3dBm and consumes 22.9mW of power on the 1.4V power supply.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.12
• /
• pp.3679-3683
• /
• 2010

Niobium oxide ($Nb_2O_5$) and phosphated $Nb_2O_5$ were synthesized and used as catalysts for sorbitol dehydration to isosorbide. The characterization results of $N_2$ adsorption, XRD and $NH_3$-TPD revealed that the phosphoric acid modification could well prevent the crystallization of $Nb_2O_5$. And the amorphous phosphated $Nb_2O_5$ catalysts kept the relatively large surface area and stable acidity at high calcination temperature. The catalytic results showed that the selectivity to isosorbide could be dramatically enhanced over phosphated $Nb_2O_5$. The excellent catalytic performance with 100.0% sorbitol conversion and 62.5% isosorbide selectivity were obtained over the 0.8P/NBO-400 catalyst. Comparing with $Nb_2O_5$ catalysts, phosphated $Nb_2O_5$ catalysts regenerated through a simple calcination process showed no significant activity loss after recycling three runs.