• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.10
• /
• pp.42-51
• /
• 1998

This paper suggests a congestion control scheme for CL (ConnectionLess) overlay network using the feedback loops between CL user and CL server, between CL servers, and between end-to-end CL users, and the header translation table of CL server. The CL overlay network for CBDS(Connectionless Broadhand Data Service) defined by ITU-T((International Telecommunication Union-Telecommunication) consists of CL servers which route frames and links which connect between CL user and CL server or between CL servers. In the CL overlay network, two kinds of congestion, CL link congestion and CL server congestion, may occur. We considered the schemes to solve the congestion. link-by-link method[18] has used the ABR feedback loops of ATM layer between CL user and CL server or between CL servers, and the congestion table using header translation table of CL server. As in congestion of output virtual channel this method has an effect on all the traffic transmitting through the link, then it has an effect on the traffic that has not caused the congestion. As a result, the link utilization of output virtual channel that does not bring the congestion and outputs the traffic is decreased. To overcome this drawback of link-by-link, we proposed the hybrid method that are using the ABR feedback loops of link-by-link method, the feedback loop between CL users in end-to-end, the congestion table using and the header translation table. This scheme deals with teh congestion immediately by link-by-link loops and the header translation table, and then regulates the sending rate of CL user that causes the congestion by end-to-end loop.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.2
• /
• pp.89-96
• /
• 2009

As increasing the number of digital control devices installed on aircrafts and their transmission speed, various digital data buses have been introduced to provide reliable and high-speed characteristics. These characteristics of avionics data bus are highly related on the fault-tolerant performance which can make minimize jitter and loss during data transfer. In this paper, we concerned about a new traffic shaping scheme for increasing the reliability of Avionics Full Duplex Switched Ethernet (AFDX) systems based on ARINC 664 standard. We note that the conventional AFDX with a single regulator per virtual link system may produce aggregated traffics as the number of virtual links increasing. The aggregated traffic results in large jitters among frames. To remedy for the jitter and loss of data, we propose a dual regulator scheme for the AFDX system. The purpose of the additional regulator is to additionally regulate aggregated traffics from a number of per virtual link regulators. Using NS-2 simulator, we show that the proposed scheme provides a better performance than the single regulator one. It is worthwhile note that the proposed AFDX with Dual Regulator scheme can be employed to not only aircraft networks but other QoS sensitive networks for robot and industrial control systems.

• The Plant Pathology Journal
• /
• v.36 no.6
• /
• pp.536-557
• /
• 2020

Sugarcane yellow leaf virus (SCYLV) is a distinct member of the Polerovirus genus of the Luteoviridae family. SCYLV is the major limitation to sugarcane production worldwide and presently occurring in most of the sugarcane growing countries. SCYLV having high genetic diversity within the species and presently ten genotypes are known to occur based on the complete genome sequence information. SCYLV is present in almost all the states of India where sugarcane is grown. Virion comprises of 180 coat protein units and are 24-29 nm in diameter. The genome of SCYLV is a monopartite and comprised of single-stranded (ss) positive-sense (+) linear RNA of about 6 kb in size. Virus genome consists of six open reading frames (ORFs) that are expressed by sub-genomic RNAs. The SCYLV is phloem-limited and transmitted by sugarcane aphid Melanaphis sacchari in a circulative and non-propagative manner. The other aphid species namely, Ceratovacuna lanigera, Rhopalosiphum rufiabdominalis, and R. maidis also been reported to transmit the virus. The virus is not transmitted mechanically, therefore, its transmission by M. sacchari has been studied in different countries. SCYLV has a limited natural host range and mainly infect sugarcane (Sachharum hybrid), grain sorghum (Sorghum bicolor), and Columbus grass (Sorghum almum). Recent insights in the protein-protein interactions of Polerovirus through protein interaction reporter (PIR) technology enable us to understand viral encoded proteins during virus replication, assembly, plant defence mechanism, short and long-distance travel of the virus. This review presents the recent understandings on virus biology, diagnosis, genetic diversity, virus-vector and host-virus interactions and conventional and next generation management approaches.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.4
• /
• pp.319-327
• /
• 2010

A nuclear plant ESF ACS simulator was designed, built, and verified to perform experiment related to ESF ACS of nuclear power plants. The dimension of 3D CAD model was based on drawings of the main control room(MCR) of Yonggwang units 5 and 6. The CFD analysis was performed based on the measurement of the actual flow rate of ESF ACS. The air flowing in ACS was assumed to have $30^{\circ}C$ and uniform flow. The flow rate across the HEPA filter was estimated to be 1.83 m/s based on the MCR ACS flow rate of 12,986 CFM and HEPA filter area of 9 filters having effective area of $610{\times}610mm^2$ each. When MCR ACS was modeled, air flow blocking filter frames were considered for better simulation of the real ACS. In CFD analysis, the air flow rate in the lower part of the active carbon adsorber was simulated separately at higher than 7 m/s to reflect the measured value of 8 m/s. Through the CFD analyses of the ACSes of fuel building emergency ventilation system, emergency core cooling system equipment room ventilation cleanup system, it was confirmed that all three EFS ACSes can be simulated by controlling the flow rate of the simulator. After the CFD analysis, the simulator was built in nuclear grade and its reliability was verified through air flow distribution tests before it was used in main tests. The verification result showed that distribution of the internal flow was uniform except near the filter frames when medium filter was installed. The simulator was used in the tests to confirm the revised contents in Reg. Guide 1.52 (Rev. 3).

• Radiation Oncology Journal
• /
• v.24 no.3
• /
• pp.192-200
• /
• 2006

[ $\underline{Purpose}$ ]: To evaluate the movement of surgical clips implanted in breast tumor bed during normal breathing. $\underline{Materials\;and\;Methods}$: Seven patients receiving breast post-operative radiotherapy were selected for this study. Each patient was simulated in a common treatment position. Fluoroscopic images were recorded every 0.033 s, 30 frames per 1 second, for 10 seconds in anterior to posterior (AP), lateral, and tangential direction except one patient's images which were recorded as a rate of 15 frames per second. The movement of surgical clips was recorded and measured, thereby calculated maximal displacement of each clip in AP, lateral, tangential, and superior to inferior (SI) direction. For the comparison, we also measured the movement of diaphragm in SI direction. $\underline{Results}$: From AP direction's images, average movement of surgical clips in lateral and SI direction was $0.8{\pm}0.5\;mm$ and $0.9{\pm}0.2\;mm$ and maximal movement was 1.9 mm and 1.2 mm. Surgical clips in lateral direction's images were averagely moved $1.3{\pm}0.7\;mm$ and $1.3{\pm}0.5\;mm$ in AP and SI direction with 2.6 mm and 2.6 mm maximal movement in each direction. In tangential direction's images, average movement of surgical clips and maximal movement was $1.2{\pm}0.5\;mm$ and 2.4 mm in tangential direction and $0.9{\pm}0.4\;mm$ and 1.7 mm in SI direction. Diaphragm was averagely moved $14.0{\pm}2.4\;mm$ and 18.8 mm maximally in SI direction. $\underline{Conclusion}$: The movement of clips caused by breathing was not as significant as the movement of diaphragm. And all surgical clip movements were within 3 mm in all directions. These results suggest that for breast radiotherapy, it may not necessary to use breath-holding technique or devices to control breath.

• The KIPS Transactions:PartA
• /
• v.11A no.5
• /
• pp.383-390
• /
• 2004

This paper propose a method that controls facial expression of 3D avatar by having the user select a sequence of facial expressions in the space of facial expressions. And we setup its system. The space of expression is created from about 2400 frames consist of motion captured data of facial expressions. To represent the state of each expression, we use the distance matrix that represents the distances between pairs of feature points on the face. The set of distance matrices is used as the space of expressions. But this space is not such a space where one state can go to another state via the straight trajectory between them. We derive trajectories between two states from the captured set of expressions in an approximate manner. First, two states are regarded adjacent if the distance between their distance matrices is below a given threshold. Any two states are considered to have a trajectory between them If there is a sequence of adjacent states between them. It is assumed . that one states goes to another state via the shortest trajectory between them. The shortest trajectories are found by dynamic programming. The space of facial expressions, as the set of distance matrices, is multidimensional. Facial expression of 3D avatar Is controled in real time as the user navigates the space. To help this process, we visualized the space of expressions in 2D space by using the multidimensional scaling(MDS). To see how effective this system is, we had users control facial expressions of 3D avatar by using the system. As a result of that, users estimate that system is very useful to control facial expression of 3D avatar in real-time.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.8C
• /
• pp.1113-1124
• /
• 2004

In this paper, we proposed a hardware(H/W) structure which can compress and recontruct the input image in real time operation and implemented it into a FPGA platform using VHDL(VHSIC Hardware Description Language). All the image processing element to process both compression and reconstruction in a FPGA were considered each of them was mapped into H/W with the efficient structure for FPGA. We used the DWT(discrete wavelet transform) which transforms the data from spatial domain to the frequency domain, because use considered the motion JPEG2000 as the application. The implemented H/W is separated to both the data path part and the control part. The data path part consisted of the image processing blocks and the data processing blocks. The image processing blocks consisted of the DWT Kernel fur the filtering by DWT, Quantizer/Huffman Encoder, Inverse Adder/Buffer for adding the low frequency coefficient to the high frequency one in the inverse DWT operation, and Huffman Decoder. Also there existed the interface blocks for communicating with the external application environments and the timing blocks for buffering between the internal blocks The global operations of the designed H/W are the image compression and the reconstruction, and it is operated by the unit of a field synchronized with the A/D converter. The implemented H/W used the 69%(16980) LAB(Logic Array Block) and 9%(28352) ESB(Embedded System Block) in the APEX20KC EP20K600CB652-7 FPGA chip of ALTERA, and stably operated in the 70MHz clock frequency. So we verified the real time operation of 60 fields/sec(30 frames/sec).

• Korean Journal of Environment and Ecology
• /
• v.25 no.6
• /
• pp.893-902
• /
• 2011

The purpose of this study was to survey structures and growth conditions of Pinus densiflora village groves, and to establish management strategies for their desirable growth and conservation. Twelve village groves were selected in western Gangwon province for the study. The age of the study groves ranged from 50 to 200 years. Average dbh (diameter at breast height) and density of trees for each study grove were 27~52cm and 0.5~9.3 trees/$100m^2$, respectively. Soil environments were favorable to Pinus densiflora growth in the majority of the study groves, but 2 study groves with sandy soils showed considerably poor nutrient contents. Low tree vitality was found in some of the study groves due to poor conditions of root growth from soil fill and trampling. There were detachment of cambial tissue and damage of stem cavity at 6 study groves, which were caused by artificial injury, careless pruning, and frost damage. Light disease damage by Rhizosphaera kalkhoffii and phomopsis blight were found at 6 study groves. Light pest damage by Thecodiplosis japonensis was also found at 6 study groves, but the pest damage at 2 study groves was relatively considerable. Thus, major factors limiting normal growth of Pinus densiflora village groves were infertility, soil fill and trampling, stem damage, and disease and pest. Desirable management strategies were explored to solve growth-related problems and to conserve the study groves. The management strategies included fertilization of organic matter and lime, removal of soil fill, soil plowing and graveling, wood-trail installation or woodchip mulching, supply of wood fences and protective frames, surgical operation for damaged stems, vitality enhancement, and trunk injection to improve growth environments or control stem damage and disease/pest.

• Archives of design research
• /
• v.18 no.4 s.62
• /
• pp.119-128
• /
• 2005

This paper presents an intuitive 3D modeling interlace based on a field study and prototype development. The process and tools of modeling were observed in workshops of professional design model making, day modeling, wood caning and glass crafting. The Spray Modeling interlace was developed from the observational analysis of the field study. It is a 3D modeling interface which combines particle spraying and day modeling in Virtual or Augmented Reality space. Virtual volume particles are sprayed on frames in Augmented Reality space as day modeling. It adopts a real air spay gun as a tangible interface device which provides coherent sound and air-force feedback. The prototype development and a user study showed that the interface supports new patterns of form development and expression. Control interfaces and requirements of auxiliary devices were found to be improved. This study examines the potential of the new interlace for designers working in 3D virtual and augmented reality. The new spraying interface is also expected to be used as an alternative interface in 3D computer workspace, games, education software and media art.

• Archives of design research
• /
• v.13 no.4
• /
• pp.233-242
• /
• 2000

The traditional image of hydraulic excavator started to change in two ways since 1990. First, post-heavy equipment's visual image was new waves to traditional image of heavy, strong, and wild. They are the negative aspect that excavators have. Another movement of getting rid of its negative image can be found in late-heavy equipment, which was intended to adapt traditional and positive, but off negative images. In 1990s, the design trend is moving from warm/hard to warm/soft, and KOBELCO can be exceptional example that went even further, gone up to cool-soft image. KOBELCO specially aimed 'post- excavator image' strategy, which has been successful. Image of cabin as a human space changed little bit further than outside image. Each company tried to differentiate the design of cabin focusing on its safety. Following paragraphs show specific trend of image change in form, colour, texture, and the composition. Major visual image change in form tries to follow the image of cars and home appliances which are showing the movement from tough and hard image to soft one. Structural change on local image shows the movement from angular edge to edgeless and the movement of cabin's pillar C placed to back of the equipment with gentle inclination. All of these movements are the result of effort to improve traditional excavator's negative image, that top structure is assembled separately, to positive ones. Today's tendency about its color becomes important to apply two different colour styles. Each style has brightness and tone comparison. As an enormous power convey system, it was in common that its brightness comparison was useful because of the alarm of its damage possibility. However, as its colour control and its design have been emphasized gradually, the tone comparison takes a part in an important role, too. As an example, there is an occasion that these comparisons are compromised simultaneously. In the respect of its image creation, its texture treatments make the tendency of being the same as passenger cars. It is caused from its development of the manufacture techniques of from the fabrication method in small business to the press method in big firm. Further, it is also because of its improvement of painting & coating skills. It may prohibit the reflection effect from solar rays. In the point of view of its visual images, it is recognized the prominent tendency that its composition has been gradually decreased. Lots of windows and the frames tends dark-colour as a whole. It is more preferred to have one colour image, but except KOBELCO and HITACHI. As well, there is another high-tendency to improve its standard treatments, especially for its corner and texture treatments.