• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.619-624
• /
• 2004

This paper applies the fuzzy logic controller to a semiactive seat suspension system in order to obtain the better ride comfort in constraint of specific rattle space. The seat suspension system used for this research is a scissors-type one with the MR (Magnetic Rheological) fluid damper. Since a seat suspension system with a driver can not be exactly modeled, it is effective to control with the fuzzy logic controller. The rule was carefully tuned to effectively reduce the vibration transmitted to a driver. The on-road ride was realized on a hydraulic excitor and the result shows that the fuzzy controller has reduced the vibration of a seat suspension system compared to the continuous skyhook controller.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.1
• /
• pp.17-23
• /
• 2004

The semi-active suspension system is getting widely adopted in passenger vehicles for its ability to improve ride comfort over the passive suspension system while not degrading driving safety. A key to the success is to develop practical controllers that yield performance enhancement over the passive damper under various driving conditions. To this end, several control strategies have been studied and evaluated in this research in consideration of practical aspects such as nonlinearity and dynamics of the damper. From simulation results. it has been observed that, with the proposed control schemes, ride comfort can be significantly upgraded while suppressing degradation of driving safety.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.895-902
• /
• 2007

Rotating machinery has two typical faults with clearance, one is partial rub and the other is looseness. Due to these faults, non-linear and non-stationary signals are occurred. Therefore, time-frequency analysis is necessary for exact fault diagnosis of rotating machinery. In this paper newly developed time-frequency analysis method, HHT(Hilbert-Huang Transform) is applied to fault diagnosis and compared with other method of FFT, SFFT and CWT. The results show that HHT can represent better resolution than any other method. Consequently, the faults of rotating machinery are diagnosed efficiently by using HHT.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.480-483
• /
• 2007

Recently, many apartment houses were built in nearby road and railway. Road traffic noise level and railroad traffic noise level are important factors on apartment houses inhabitant's acoustic comforts. The measurement methods which noted by Ministry of Construction & Transportation, Ministry of Environment and Korean Industrial Standard are used for measurement of exterior noise at apartment houses. The purpose of this study compare the noise level characteristic by the measuring methods and evaluating methods. The results show that road traffic noise in the daytime appeared by not greatly noise level difference by the measuring method and evaluating methods. But railroad traffic noise appeared by greatly the noise level difference by the equivalent noise level(1hour) and continuous time.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.421-424
• /
• 2007

Currently domestic criteria for the aircraft noise is being adapted WECPNL(weighted equivalent continuous perceived noise level), while internationally preferred method is $L_{dn}$ which is based on from $L_{eq}$ and can also evaluate environmental noise. WECPNL used in domestic as an evaluation metric is only for the aircraft noise. It is, therefore, not adequate for the evaluation of residents' injury, moreover, it is very difficult to measure the aircraft noise by WECPNL due to the complicated calculating procedures as long as automatic measuring system is not used. Accordingly, this study aims to propose alternative evaluation metric for the aircraft noise. To achieve this purpose, WECPNL, $L_{eq}$, $L_{dn}$, other metrics and criteria were compared and analyzed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.8
• /
• pp.636-642
• /
• 2014

The sensor configuration of the magnetostrictive guided wave system can be described as a single continuous transducing element which makes it difficult to separate the individual modes from the reflected signal. In this work we develop the mode decomposition technique employing chirplet transform, which is able to separate the individual modes from dispersive and multimodal waveform measured with the magnetostrictive sensor, and to estimate the time-frequency centers and individual energies of the reflection, which would be used to locate and characterize defects. The reflection coefficients are calculated using the modal energies of the separated mode. Results from experimental results on a carbon steel pipe are presented, which show that the accurate and quantitative defect characterization could become enabled using the proposed technique.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.10
• /
• pp.857-864
• /
• 2016

In this study, we proposed a novel concept of electric sun visor comprising a dark, see-through sun shade material that ensures unimpaired driver's vision with continuous control of the shade position. The shade extending from the windshield base along its surface may be subjected to severe vibration during driving unless the design parameters are carefully selected. A prototype was tested to collect acceleration data during driving. Based on the test data, an ADAMS dynamics model was validated. The mechanism of sun visor was optimized to minimize vibration based on the dynamics model, experimental design, and response surface method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.176-181
• /
• 2002

The continuous Gabor wavelet transform (GWT) has been utilized as a useful time-frequency analysis tool to identify the rapidly-varying characteristics of some wave signals. In the application of GWT, it is important to select the Gabor wavelet with the optimal shape factor by which the time-frequency distribution of a signal can be accurately estimated. To find the signal-dependent optimal Gabor wavelet shape factor, the notion of the Shannon entropy which mesures the extent of signal energy concentration in the time-frequency plane is employed. To verify the validity of the present entropy-based scheme, we have applied it to the time-frequency analysis of a set of elastic bending wave signals generated by an impact in a solid cylinder.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.630-635
• /
• 2002

This work is concerned with the damage size estimation by using propagating bending wave signals in a beam. For the accurate estimation, we apply the continuous wavelet transforms to the incident waves and the reflected waves from a small damage in a long cylindrical beam. In particular, we propose to use the ratio of the magnitude of the incident and reflected waves along the ridges in the wavelet-transformed time-frequency plane. This technique is applied to the signals measured by non-contact magnetostrictive sensors. Experimental results indicate that the present method using the magnetostrictive sensor can be quite effective for accurate damage size estimation with simple measurements.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.200-205
• /
• 1998

Although discretization methods such as the transfer matrix method (TMM) and the finite element method (FEM) have played an important role in the design or analysis of rotor-bearing systems, continuous system modeling and analysis are often desirable especially for sensitivity analysis or design. The present paper proposes a comprehensive modeling procedure to obtain exact solution of general rotor-bearing systems. The proposed method considers a Timoshenko beam model and makes use of complex coordinate in the formulation. The proposed method provides exact eigensolutions and frequency response functions (FRFS) of general multi-stepped rotor-bearing systems. The first numerical example compares the proposed method with FEM. The numerical study proves that the proposed method is very efficient and useful for the analysis of rotor-bearing systems.