• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 춘계학술대회 논문집
• /
• pp.421-426
• /
• 2003

Dropper which can get to suspend contact wire should be installed with a uniform distribution, so that electric locomotive can have good characteristics of current collection. Because dropper distribution is changed according to a circumstances in the construction field, it is hard to calculate and construct a overhead line. Therefore, in this study, a program was developed to calculate the dropper length in the normal and elevation section. Through the program, it is possible to perform a accurate construction of overhead line and contribute to a improvement of current collection as well.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 춘계학술대회 논문집
• /
• pp.598-605
• /
• 2000

The design of a current collection system of high speed train requires the fundamental understandings fer the dynamic characteristics of a catenary system and pantograph. The stiffness of the catenary system of high speed train has the varying characteristics for the change of the contact point with a pantograph, since the supporting pole and hanger make the different boundary conditions for the updown stiffness of a trolley wire. The variation of stiffness results in Mathiue equation, which characterizes the stability of the system. However, the two terms variation of the stiffness due to span length and hanger distance cannot be solved analytically. In this paper, the stiffness variations are calculated, and the physical reasoning of linear model and one term Mathieu equation are reviewed. And the numerical analysis for the two term variation of the stiffness is done for the several design parameters of the pantograph.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.723-730
• /
• 2006

In the electrical railway, the tension ascension of contact wire is essential to speed up of train and current collection performance of catenary largely depends on the tension. The tension variation rate of the tensioning device used in existing line limits within 5%, and the tension variation rate of the spring-type tensioning device installed at the section where tensioning length is short bounds within 15%. So it is urgent for us to localize it for high speed line, which the tension variation rate is limited within 3%. Therefore in this study, a pulley-type tensioning device for high speed line is developed. To verify the performance of developed device, a performance test, overload test and failure test is carried out under the code of the Kyung-Bu High Speed line. And it is secured durability performance through a fatigue test.

• International Journal of Railway
• /
• 제3권2호
• /
• pp.46-53
• /
• 2010

Electric railroad systems consist of rolling stock, track, signal and catenary system. In the catenary system, one of the most important factors is the impedance according to the design and characteristic. Before the catenary system is designed, the impedance should be precedently researched. The railroad catenary system is complex system which is composed by five conductors. The five conductors classify up and down feeders, up and down contact wire group, rail group. Therefore, we should compose the catenary system of the equivalent five-conductors model. In this paper, we suggest a geometrical model and a equivalent conductor model by using geometric mean radius of five conductors in the catenary system. Also, we calculate demanded parameter values in the model. By using those, line constants of five conductors are analyzed by applying the equivalent method called as the condensed joint matrix.

• 한국해양공학회지
• /
• 제26권2호
• /
• pp.33-38
• /
• 2012

The effects of the diffusible hydrogen content and hardness on the cold cracking in high strength weld metal were investigated. The diffusible hydrogen contents were influenced by welding parameters such as the voltage and contact tip-to-work distance (CTWD). The diffusible hydrogen content increased with an increase in voltage. However, it was decreased with an increase in CTWD. CTWD also influenced the weld metal hardness,especially when the wire used had a higher strength than the base metal. This showed that weld metal hardness had a more powerful effect on weld metal cold cracking than the diffusible hydrogen content in this experiment.

• 전기학회논문지
• /
• 제64권12호
• /
• pp.1810-1817
• /
• 2015

The railway vehicle has an auxiliary power unit for supplying power to the associated electronic control devices and passenger service unit. Typically, input voltage from the catenary for rolling stock is highly fluctuating according to the substation capacity, vehicle propulsion and regeneration. Especially, the frost and freezing on contact wire in winter can cause a blackout inside vehicle, and also brings about electronic components damaging and the system down. To prevent this problem, a large filter and capacitor is used. But this is not a perfect solution, because it is increasing weight of the unit. In this paper, a new algorithm is proposed to suppress the disturbance without adding devices. Simulation and experimental results show that the proposed algorithm has performance to suppress the disturbance at the sudden input voltage variations.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.502-502
• /
• 2007

전차선로는 각 경간마다 양단으로 지지점을 갖게 되므로 지지점에서의 탄성도와 경간중앙에서의 탄성도가 같을 수 없다. 이 두 지점의 탄성도의 차이를 나타내는 계수로 불균일율이라는 지수가 정의되어 널리 사용되어왔다. 이 불균일율은 전차선 장력과 경간 길이에 크게 영향 받는다. 그러나 드로퍼의 배치 간격에 따라서도 달라진다. 이 불균일율은 전차선로의 동적인 특성을 예측하는 하나의 변수로 활용되고 결국 집전 성능을 상대 비교하여 판단하는데 활용되며, 직접적으로는 드로퍼 간격을 설계하는데 있어서 중요한 파라미터로 사용되고 있다. 그러나 이 불균일율은 전차선로의 동적 성능을 적절히 반영하는 지수가 되지 못하고 있다고 판단하고 있다. 불균일율의 정의인 경간 중앙에서의 탄성율과 경간 끝 지정의 탄성율과의 단순한 차이 값의 크기만으로는 드로퍼의 수와 배치 간격에 따른 특성을 반영하지 못한다고 판단된다. 이를 여러 가지 다양한 케이스를 가정하여 탄성도 해석 프로그램을 이용하여 평가해본다. 평가 결과를 토대로 드로퍼 수에 따른 보정계수를 갖는 새로운 불균일율 평가 지수를 제시하고자 하며 이 새로운 지수가 기존의 지수보다 보다 집전 성능을 판단하는데 유용한 데이터가 됨을 증명한다. 또한 아울러 불균일율이 다른 가선 구조에 대하여 팬터그래프의 1단과 2단의 스프링 계수의 크기와의 조합과 상환 관계에 따른 집전 성능의 차이를 전차선로-팬터그래프 동역학 시뮬레이션 프로그램을 사용하여 평가한다. 이를 통하여 불균일율에 따른 보다 적절한 팬터그래프 동역학 모델을 제시한다.

• 한국자동차공학회논문집
• /
• 제13권3호
• /
• pp.102-109
• /
• 2005

Wheel-slip control systems are able to control the braking force more accurately and can be adapted to different vehicles more easily than conventional ABS systems. But, in order to achieve the superior braking performance through the wheel-slip control, real-time information such as the tire braking force is required. For example, in the case of EHB (Electro-Hydraulic Brake) systems, the tire braking force cannot be measured directly, but can be approximated based on the characteristics of the brake disk-pad friction. The friction characteristics can change significantly depending on aging of the brake, moisture on the contact area, heat etc. In this paper, a wheel slip The proposed wheel slip control system is composed of two subsystems: braking force monitor and robust slip controller In the brake force monitor subsystem, the tire braking forces as well as the brake disk-pad friction coefficient are estimated considering the friction variation between the brake pad and disk. The robust wheel slip control subsystem is designed based on sliding mode control methods and follows the target wheel-slip using the estimated tire braking forces. The proposed sliding mode controller is robust to the uncertainties in estimating the braking force and brake disk-pad friction. The performance of the proposed wheel-slip control system is evaluated in various simulations.

• 한국강구조학회 논문집
• /
• 제10권4호통권37호
• /
• pp.589-600
• /
• 1998

본 연구는 케이블의 피로실험에서 라틴방격법의 유용성을 입증하고, 현수교에서의 행어로서 사용되는 와이어로프의 축방향 피로거동을 보기 위하여 계획되었다. 평균 응력, 응력범위, 시편의 길이를 실험 인자로 선정하였다. 위에 선정한 인자의 효과는 응력 범위의 효과를 제외하고는 이론이 제기되고 있다. 각 인자에서는 3개의 수준이 사용되었다. 각 셀에서 자유도를 증가시키기 위하여 3번을 반복 수행하였다. 피로파괴의 주요 원인은 격자 접촉점에서의 접촉성 피로(fretting fatigue)였다. 선정된 3개의 인자는 모두 유의하였다. 응력범위의 효과는 예측된 바와 같았으며, 길이효과는 예상과 반대의 결과를 보여주었고, 응력수준의 효과는 채택된 응력수준에 따라 실험결과가 달라질 수 있음을 보여줬다. 그러므로 라틴방격법은 직교성이 갖춰진다면 피로거동에 영향을 미치는 인자들을 규명하는 데에 매우 효과적인 실험 방법임을 알 수 있다.

• 소성∙가공
• /
• 제22권1호
• /
• pp.23-29
• /
• 2013

In this study, a micro/nano-random-pattern-structure surface was machined by electric discharge machining (EDM) followed by replicating the EDM surface with a silicone elastomer having low energy and greater hydrophobicity. The variation of hydrophobicity was of prime interest and was examined as a function of the surface roughness of the replicated silicone elastomer. The hydrophobicity was evaluated by the water contact angle (WCA) measured on the relevant surface. For the experiments, the original surfaces were machined by die sinking electric discharge machining (DS-EDM) and wire cutting electric discharge machining (WC-EDM). The ranges of surface roughness were Ra $0.8{\sim}19{\mu}m$ for the DS-EDM and Ra $0.5{\sim}4.7{\mu}m$ for the WC-EDM. In order to fabricate a hydrophobic surface, the EDM surfaces were directly replicated using a liquid-state silicone elastomer, which was thermally cured. The measured WCA on the replicated surfaces for DS-EDM was in the range of $115{\sim}130^{\circ}$ and for WC-EDM the WCA was in the range of $123{\sim}150^{\circ}$. Additionally, the dynamic hydrophobicity was evaluated by measuring an advancing and a receding WCA on the replicated silicone elastomer surfaces.