• 콘크리트학회논문집
• /
• 제13권5호
• /
• pp.491-498
• /
• 2001

본 연구에서는 강우와 같은 열 충격으로 보수체의 손상(표면 균열, 경계면 파괴)을 유발하는 표면 인장 응력과 기층과 보수층 경계면의 연직 인장 응력 및 진단 응력이 해석적으로 조사되었다. 응력 계산 시에는 사용 재료의 비선형 응력-변형률 곡선이 사용되었고, 특히 변형률 경화, 변형률 연화 특성이 고려되었다. 응력 계산은 보수층의 두께와 보수 재료를 변수로 하여 강우 강도별로 조사되었다. 강우 초기의 보수체의 온도는 하절기에 55$^{\circ}C$까지 가열됐다고 가정하였고, 강우 온도는 1$0^{\circ}C$로 결정하였다. 강우 빈도 1년 1회, 강우 지속 시간 10분, 60분의 강우 하중으로 응력을 계산한 결과, 보수체 표면에서는 실제 균열은 발생치 않고, 단지 변형률 연화 단계의 가상 균열만 형성되었다. 한편 경계면에서는 부착 전단 파괴는 발생치 않았으며, 연직 인장 파괴를 유발하는 음력이 일정한 강우 강도 및 보수 재료에서 보수층의 두께(do)가 클수록 증가하는 것으로 나타나, 경계면의 연직 인장 응력이 보수체의 안전성에 주요한 변수임을 알 수 있었다. 따라서 강우시 경계면의 파괴 예방을 위해 보수 재료의 성질 및 보수층의 두께를 결정할 수 있는 연직 인장 음력의 예측식을 제안하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1326-1330
• /
• 2008

The failure mode of steel road wheels in a vehicle is cracks from ventilation hole through to contact plane on steel wheel's disc plate. But a number of cracks of Cornering Fatigue Limit Test is on contact plane near to wheel nut mounting area, even though it's satisfied with specified cycles. So this paper searches out causes to improve durability and reliability of C.F.T by uni-axial bending moment test. The verified cause is a "fretting" on contact area of steel wheel. In result, this paper suggests a solution to prevent a fretting by inserting a damping shim, 0.7mm between steel wheel contact areas. Therefore this paper makes it possible to move crack position of C.F.T in steel wheel from contact plane to vehicle's failure mode.

• Nuclear Engineering and Technology
• /
• 제51권5호
• /
• pp.1314-1321
• /
• 2019

In case of multiple failure scenario, such as LOCA with ECCS failure, the decay heat continues to raise the reactor core temperature, eventually leading to the core voiding. In such scenario the convective heat transfer becomes poor and the majority of the heat transfer from fuel bundle takes place by radiation mode. During this abnormal working condition, if the channel pressure is less than 1 MPa, the PT sags and come in contact with the CT. This results in high rate of heat transfer from contact location to moderator. The present paper aims to capture the temperature profile over a simulated nuclear channel during such scenario at a steady state temperature of $600^{\circ}C$ (Centre pin) at two different configurations of PT i.e. PT concentric with CT and PT contact with CT. The results showed that the bottom nodes of all the components (Fuel bundle, PT and CT) of the simulated channel was greatly influenced by the PT/CT contact. Moreover, higher temperature were observed at top nodes of the PT and outer pins of the fuel bundle. However, no significant variation in temperatures were obtained in fuel bundle and CT in concentric condition.

• Tribology and Lubricants
• /
• 제35권4호
• /
• pp.229-236
• /
• 2019

This study investigates the stress singularity that occurs at the contact edge of three bodies in a frictional complete contact. We use the asymptotic analysis method, wherein we constitute an eigenvalue problem and observe the eigenvalue behavior, which we use to obtain the order of the stress singularity. For the present geometry of three bodies in contact, a contact between a cracked indenter and half plane is considered. This is a typical geometry of the PCMI problem of a nuclear fuel rod. Thus, this paper, specifically presents the characteristics of the PCMI problem from the perspective of stress singularity. Consequently, it is noted that the behavior of the stress singularity varies with the difference in the crack angle, coefficient of friction, and material dissimilarity, as is observed in a frictional complete contact of two bodies. In addition, we find that the stress singularity changes essentially linearly with respect to the coefficient of friction, regardless of the variation in the crack angle and material dissimilarity. Concurrently, we find the order of singularity to be 0.5 at a certain coefficient of friction, irrespective of the crack angle, which we also observe in the crack problem of a homogeneous and isotropic body. The order of singularity can also exceed 0.5 in the frictional complete contact problem of three bodies. This implies that the propensity for failure when three bodies are in frictional complete contact can be even worse than that in case of a failure induced by a crack.

• 한국안전학회지
• /
• 제34권5호
• /
• pp.22-30
• /
• 2019

In 2018, overload, overcurrent, insulation aging, and a contact failure caused 659 electric fires. There is almost no failure of electrical socket outlets during their manufacturing or installation period. After several months or several years, overload or overcurrent of electrical socket outlets leads to a contact failure or short circuit which causes an electric fire. Therefore, this paper analyzed for thermal characteristics based on a current value and the change in insulation resistance along with a temperature rise caused by electrical socket outlets and the state of laboratory use in workplaces. As a results, regarding the thermal characteristics based on the current value of each installation year, a temperature increase was related to a current value, an installation year, and whether the contact unit is corroded. Insulation resistance began to decrease when a temperature increased to a certain level. With a lapse of installation year, the temperature at which insulation resistance began to decrease was lowered. This paper can be applicable for the survey data about electrical socket outlet induced fire accidents and management guidelines.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.322-326
• /
• 2001

Hard disk drive(HDD) consists of a head/slider system which flies over the magnetic disk at an extremely low height. As the density of HDD increases the flying height of the head needs to be decreased. This increases the chance for contact between the slider and the disk. This paper addresses some key issues related to surface failure characteristics of HDD. It is shown that flying behavior of the slider during contact-start-stop cycle can be analyzed based on different regimes of air film lubrication, experimental methods for identifying the underlying mechanisms and improving the reliability of HDD are discussed.

• Steel and Composite Structures
• /
• 제20권5호
• /
• pp.983-997
• /
• 2016

The aim of this study is to investigate the impact behavior and impact-induced damage of sandwich composites made of E-glass/epoxy face sheets and PVC foam. The studies were carried out on square flat and curved sandwich panels with two different radius of curvatures. Impact tests were performed under impact energies of 10 J, 25 J and 80 J using an instrumented drop-weight machine. Contact force and displacement versus time and contact force- displacement graphs of sandwich panels were presented to determine the panel response. Through these graphs, the energy absorbing capacity of the sandwich panels was determined. The impact responses and failure modes of flat and curved sandwich panels were compared and the effect of curvature on sandwich composite panel was demonstrated. Testing has shown that the maximum contact force decrease while displacement increases with increasing of panel curvature and curved panels exhibits mixed failure mode, with cylindrical and cone cracking.

• Tribology and Lubricants
• /
• 제5권2호
• /
• pp.60-67
• /
• 1989

For the life prediction and fatigue failure prevention of the constant velocity joint, the maximum equivalent stress and its location in depth from the contact area are essential. These values give the fundamental information to determine the depth of the surface hardening treatment at the contact area. Contact stresses are evaluated at the surface and subsurface of the ball groove of the Weiss type constant velocity joint. The maximum contact pressure and the maximum equivalent stress are obtained. The effects of various parameters such as the radius of ball groove, friction coefficient, and residual stress are studied. The maximum equivalent stress and the maximum contact pressure increase as the radius of the ball grove increases. The location of the maximum equivalent stress moves toward surface as the friction coefficient increases. It was also found that the maximum equivalent stress becomes minimum when the compressire residual stress is about 0.16 times of the maximum contact pressure.

• Composites Research
• /
• 제15권2호
• /
• pp.1-10
• /
• 2002

본 논문에서는 특성길이 방법과 실험을 통하여 핀하중을 받는 평직 유리/에폭시 적층판 체결부의 강도를 평가하였다. 특성길이 및 강도에 영향을 미치는 인자들의 효과를 연구하기 위해, 핀과 원공이 접하는 부분에 코사인 하중을 가할 경우와, 적절한 변위경계조건으로 처리할 경우, 접촉요소를 사용하여 비선형 해석을 수행하는 경우 등 총 세가지 방법으로 특성길이 및 강도를 계산하였다. 또한 체결부의 강도는 사용하는 파손식의 영향을 받게 되므로 Tsai-Wu 파손식과 Yamada-Sun 파손식을 사용하여 결과를 비교하였다. 평직으로 이루어진 적층판과 일방향 프리프레그로 이루어진 적층판 모두에서 접촉요소를 사용한 비선형 해석이 시험과 가장 일치하는 결과를 나타내었다. 일방향 프리프레그만을 사용한 적픙판 체결부에서와 달리 모든 층이 평직으로 이루어진 유리/에폭시 채결부의 경우 Tsai-Wu 파손식을 사용한 결과가 실험값과 더 잘 일치함을 알 수 있었다.

• KSTLE International Journal
• /
• 제1권1호
• /
• pp.12-20
• /
• 2000

Nano-wear and friction of carbon overcoated laser-textured and mechanically-textured computer hard disk were characterised after contact start/stop (CSS) wear test. Various analytical and mechanical testing techniques were employed to study the changes in topography, roughness, chemical elements, mechanical properties and friction characteristics of the coating arising from the contact start/stop wear test These techniques include: the atomic force microscopy (AFM), the continuous nano-indentation test, the nano-scratch test, the time-of-flight secondary ion mass spectroscopy (TOF-SIMS) and the auger electron spectroscopy (AES). It was shown that the surface roughness of the laser-textured (LT) bump and mechanically textured (MT) Bone was reduced approximately am and 7nm, respectively, after the CSS wear test. The elastic modulus and hardness values increased after the CSS test, indicating straining hardening of the top coating layer, A critical load was also identified fer adhesion failure between the magnetic layer and the Ni-P layer, The TOF-SIMS analysis also revealed some reduction in the intensity of C and $C_2$$F_59$, confirming the wear of lubricant elements on the coating surface.