• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.160-167
• /
• 2004

A two degree-of-freedom mathematical model is presented to investigate the friction mechanism of a disc brake system. A contact parameter is introduced to describe the coupling between the in-plane and the out-of-plane motions. The model with the contact parameter is considered under the assumption that the out-of-plane motion depends on the friction force along the in-plane motion. In order to describe the relationship between the friction force and the out-of plane motion, the dynamic friction coefficient is considered as a function of both relative velocity and normal farce. Using this friction law, a contact stiffness matrix along the normal direction can be obtained. The out-of-plane motion is then investigated by both the stability analysis and the numerical analysis for various parametric conditions. The results show that the stiffness parameters of the pad and the disc must be controlled at the same time. Also, the numerical analysis shows the existence of limit cycle caused by the effect of intermittent contact stiffness.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.5
• /
• pp.2019-2024
• /
• 2011

The effect of the wear of contact tips on the weld beads made by a Gas Metal Arc Welding(GMAW) process was studied. In order to correlate between the wear of tips and beads, the droplet transfer was investigated by a high speed camera and waveform shapes, and the condition of beads was examined by a low magnification camera as well. It was found that the worn contact tip had caused to shift the contact point between the tip and the welding wire which resulted in nonuniform beads. In addition, the worn contact tip had changed the welding resistance and brought about the arc instability during welding.

• Journal of the Korean Society of Physical Medicine
• /
• v.5 no.3
• /
• pp.445-453
• /
• 2010

Purpose : The purpose of this study was to investigate the effect of pelvic tilt exercise with changing the body position on foot contact pattern in the hemiplegic patients. Methods : Thirty seven hemiplegic patients were randomly divided 3 groups; control group (CG), sitting exercise group (SIEG) and standing exercise group (STEG). F-mat system and F-scan system were used for the measurement of foot contact pattern of hemiplegic side in walking. Data were analyzed statistically using paired t-test and one-way ANOVA. Results : The results were as follows : 1) Contact area of CG and SIEG were not significant difference in walking. Contact area of STEG was significant increased in walking. 2) Anteroposterior distance of COP of SIEG and STEG were significant increased in walking. Conclusion : These results suggest that pelvic tilt exercise in sitting and standing position are effective in the improvement of Anteroposterior distance of COP and gait stability are increased in only standing position.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.235-236
• /
• 2006

The contact resistance and grain boundary potential barrier of ceramic $BaTiO_3$ PTCR were investigated. The electroless plated Ni, evaporated Al, and Ag paste were chosen as electrode materials of PTCR device for comparison analysis before and after heat treatment. The contact resistance of electrode were measured by electrometer (dc), digital multimeter (dc), and LCR meter (ac). In the case of Al electroded samples, the heat treatment and protective oxide layer had high resistance and effect on the stability of PTCR effect against contact resistance degradation, but the Ag-paste had comparably high contact resistance before heat treatment and decreased after heat treatment with safe. On the other hand, the samples with electroless plated Ni electrode had good properties of contact resistance against aging.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1129-1137
• /
• 1990

Based on the formulation which incorporates large deformation and anisotropy, an elastic-plastic finite element code is developed with membrane element to include the contact treatment. For the analysis of the general sheet metal forming process with contact condition, the treatment of contact is considered by employing the successive skew coordinate system. Three kinds of sheet metal forming processes with contact conditions are analyzed; stretching of a square diaphragm with a hemispherical punch, deep drawing of a circular cup and deep drawing of a square cup. Then the computational results are compared with the experiment. The computed loads and the distribution of the thickness strain are in good agreement with the experiment for all cases. However, the computational results of the thickness strain show the effect of bending can not be ignored in the deep drawing process whereas the effect of bending is negligible in stretching.

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.1353-1359
• /
• 2004

There are many massive components added on the railway overhead-line. These components cause larger fluctuations of contact forces, which are due to wave reflections and Doppler effects when a high-speed train passes those. In this paper, mathematical formula are derived for the relation between the added mass and contact force fluctuations. Using the derived formula, we calculate a added mass on the overhead-line which cause amplification factor to become 2.5. German design practice requires that amplification factor due to the wave reflection should be less than 2.5 to obtain good current collection performance. To show the validity of the formula, simulation results are compared with the calculation results. Simulation results showed that contact force fluctuations grow rapidly when an added mass is larger than the calculation result. Therefore, the simple form of formula can be used for estimating maximum added mass not to cause large fluctuations of contact forces in early design phase.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.2
• /
• pp.59-64
• /
• 2001

The distribution of current in the conductors influenced by the armature geometry and velocity is an important parameter for determining performance of an electromagnetic launcher(EML). the electric current in the early launching stage tends to flow on the outer surfaces of the conductors, resulting in very high local electric current density. However, the tendency for current to concentrate on the surface is driven by the velocity skin effect later in launching stage. The high current density produces high local heating and, consequently, increases armature wear which causes several defects on EML system. This paper investigates the effects of rail/armature geometry on current density distribution, launcher inductance gradient (L'), and contact force. Three geometrical parameters are used here to characterize the railgun system. These are the ratio of contact length to root length, relative position of contact leading edge to root trailing edge, and the ratio of rail overhang to the rail height. The distribution of current density, L', contact force between various configurations of the armature and the rail are analyzed and compared by using the EMAP3D program.

• Toxicological Research
• /
• v.26 no.2
• /
• pp.123-130
• /
• 2010

The effect of DHU001, a mixed herbal formula consisted of 7 types aqueous extracts for various respiratory disorders were evaluated on 2,4-dinitrofluorobenzene (DNFB)-induced contact dermatitis, type I allergic model. Contact dermatitis was induced by sensitization with dinitrophenyl-derivatized ovalbumin (DNP-OVA) and DNFB challenge as antigen. Two different dosages of DHU001 (300 and 150 mg/kg) were orally administered to DNP-OVA sensitization mice once a day for 7 days with reference material, dexamethasone (15 mg/kg, intraperitoneal treatment). End of 7 days oral administration of DHU001 extracts or intraperitoneal treatment of dexamethasone, the changes on the edematous changes and scratching behavior were measured. Immediate after DNFB challenge on ear or paw of DNP-OVA sensitized mice, increases of ear and paw thicknesses and weights were detected with anterior ear skin (dermis to epidermis) thickness and paw scratching behavior increases. However, these contact dermatitis signs induced by DNFB treatment were reduced by treatment of the both different dosages of DHU001 and dexamethasone, respectively. The results obtained in this study suggest that oral treatment of DHU001 extracts also has relatively favorable effects on contact dermatitis.

• Journal of the Korean Society of Industry Convergence
• /
• v.20 no.2
• /
• pp.195-204
• /
• 2017

Predicting the failure life of automated manufacturing systems can reduce overall downtime, maintenance costs, and total plant operation costs. Therefore, there is a growing interest in fatigue failure mechanisms as the safety or service life assessment of manufacturing systems becomes an important issue. In particular, fretting fatigue is caused by repeated tangential stresses that are generated by friction during small amplitude oscillatory movements or sliding between two surfaces pressed together in intimate contact. Previous studies in fretting fatigue have observed size effects related to contact width such that a critical contact width exists where there is drastic change in the fretting fatigue life. However, most of them are the two-dimensional finite element analyses based on the plane strain assumption. The purpose of this study is to investigate the contact size effects on the three-dimensional finite element model of a finite width of a flat specimen and a cylindrical pad exposed to fretting fatigue. The contact size effects were analyzed by means of the stress and strain averages at the element integration points of three-dimensional finite element model. This study shows that the fretting fatigue life of manufacturing systems can be predicted by three-dimensional finite element analysis based on SWT critical plane model.

• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.29 no.2
• /
• pp.79-82
• /
• 2018

Background and Objectives : Laryngeal contact granuloma is benign inflammatory disease induced by excessive mechanical contact of larynx such as endotracheal intubation, voice abuse, laryngeal microsurgery as well as laryngopharygeal reflux. Because it is caused by various risk factors, multiple treatment modalities are required. The purpose of study is to evaluate treatment effect of topical steroid through nasal cavity in contact granuloma. Materials and Method : Fifty-two patients were enrolled in this study with exception of intubation granuloma. Patients were classified with four groups (Proton pump inhibitor (PPI), Nasal steroid spray (SPR), PPI+SPR, Observation) according to treatment modality. Results : Patients who treated with PPI (Odds ratio 2.45, p=0.03) and combination of PPI and SPR (Odds ratio 2.88, p<0.01) had significantly better response than patients who not treated with medical therapy. Conclusion : Combination therapy of nasal steroid spray and PPI is effective for contact granuloma of larynx and considered as a treatment of choice rather than PPI only treatment.