• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.276-278
• /
• 2005

Bridge constructed recently is preferred to have a long span and a simple structure detail considering not only functions as bridge but scenic beauty, maintenance, construction term and life cycle cost, etc. Therefore, it demands a high quality steel like a thick plate steel and a high performance steel. A TMCP steel produced by theme-mechanical control process is now spotlighted due to the weldability for less carbon equivalent. It improved at strength and toughness in microstructure. Resently the SM570-TMC steel, a high strength TMCP steel whose tensile strength is 600MPa, is developed and applied to steel structures. But, for the application of this steel to steel structures, it is necessary to elucidate not only the material characteristics but also the mechanical characteristic of welded joint. In this paper, we investigated the characteristics of residual stresses generated by welding of SM570-TMC steels through an experimental study

• Journal of Korean Society on Water Environment
• /
• v.24 no.5
• /
• pp.523-532
• /
• 2008

A phase II site investigation and feasibility study was conducted at a military mortar shooting range near the demilitarized zone (Kyunggi, South Korea) to assess the extent of contaminants migration to the nearby Imjin river in which a flood control dam is under construction. The results showed that silty-clay soils around target areas were co-contaminated with heavy metals (Cd, Cu, and Pb) and explosives (HMX, RDX, and TNT). The total amount of contaminant was estimated to be 497.1 kg-RDX, 20.6 kg-HMX, 1.4 kg-TNT, 35.2 kg-Cd, 4,331 kg-Cu, and 5,115 kg-Pb, respectively. Both heavy metals and explosives were almost equally distributed on each soil particle size fraction. Neither subsurface soil samples nor ground water samples showed signs of contamination above the environmental criteria. The major migration route of contaminants was soil particles in surface run-off during rain at which a mass discharge rate of 30.0 mg-RDX/hour was observed.

• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.5
• /
• pp.617-628
• /
• 2010

The operation performance of sewer rehabilitation projects conducted with Build-Transfer- Lease contract in Korea will be evaluated using the index of infiltration and inflow (I/I). Though I/I obtained at the fourth year should be initially evaluated based on the I/I values observed for the previous three years after the completion of sewer construction, the concrete methodology have not been proposed to rely on the so called 'performance evaluation committee'. This study suggests two statistical methodology to evaluate the I/I performance; the confidence interval method and the hypothesis-testing method. Assumed ten I/I values in each year for 20 years are used in this study. Two cases are analyzed and compared; case I to use as control data all I/I values for all years obtained before the evaluation year and case II to use I/I values for only 3 years before the evaluation year. As a result, case II tends to have relatively higher scores than case I, reflecting the low mean I/I values at the initial years.

• Asia pacific journal of information systems
• /
• v.8 no.3
• /
• pp.37-49
• /
• 1998

The basic goal of CALS is to improve transactions and relationships among organizations through information sharing and integration. CALS is an information strategy which needs strong cooperation between organizations or between users and developers in design step. However, current design methodologies using IDEF models, that are considered to be standard for CALS system development, has some limitations. For example, it is difficult for system developers to communicate with counterparts by IDEF model since IDEF models are difficult for counterparts to understand. In this paper, we suggest a development methodology for GALS systems by complementing IDEF model with Document Trace Diagram, which we developed as a communication tool, The concept of Document Trace Diagram stems from the fact that most information exchanged within or between organizations is in the form of documents and most standard operating procedures of organizations are about processing the documents. It helps system developers identify functions and their ICOMs (Input, Control, Output, Mechanism) with ease and little communication cost. With this methodology, we have constructed the GALS prototype system for construction industry.

• Journal of Information Processing Systems
• /
• v.15 no.6
• /
• pp.1326-1334
• /
• 2019

Knowledge base means a library stored in computer system providing useful information or appropriate solutions to specific area. Knowledge base associated with autism is the complex multidimensional information set related to the disease autism for its pathogenic factor and therapy. This paper focuses on the knowledge of biological molecular information extracted from massive biomedical texts with the aid of widespread used machine learning methods. Six classes of biological molecular information (such as protein, DNA, RNA, cell line, cell component, and cell type) are concerned and the probability statistics method, conditional random fields (CRFs), is utilized to discover these knowledges in this work. The knowledge base can help biologists to etiological analysis and pharmacists to drug development, which can at least answer four questions in question-answering (QA) system, i.e., which proteins are most related to the disease autism, which DNAs play important role to the development of autism, which cell types have the correlation to autism and which cell components participate the process to autism. The work can be visited by the address http://134.175.110.97/bioinfo/index.jsp.

• Journal of Drive and Control
• /
• v.9 no.4
• /
• pp.14-18
• /
• 2012

Two kinds of piezoelectric actuator are applied to the valve for controlling the direction, the flow and the pressure of the fluid. One is a stack type piezoelectric actuator which has very fast response characteristics but very tiny displacement. The other is a bender type piezoelectric actuator which has also fast response characteristics but lower than the stack type one, and has longer displacement than the stack type one. So, the bender type piezoelectric actuator has advantage to apply to the valve for controlling a large amount of flow and fast on-off operating. In this study, the bender type piezoelectric pneumatic valve for color sorter is designed and fabricated. The new type high speed piezo valve with the both side supporting mechanism for high operating frequency and high reliability is discussed for separating the foreign body from the grains. Finally, the performance characteristics of a fabricated valve are analyzed and the frequency characteristics are also discussed for substituting the conventional type solenoid actuator.

• Journal of Drive and Control
• /
• v.9 no.4
• /
• pp.1-7
• /
• 2012

The voice coil linear force motor is a kind of a direct drive motion device that uses a permanent magnetic field and coil winding to produce force. In order to design a voice coil linear force motor, an exact calculations of the required force, the flux density in air gap and the flux pathway are needed. A conventional method can be used usually to calculate the flux density in air gap, but with this method it is needed to find a magnetic circuit revision constant. In this paper a voice coil linear force motor is designed by conventional design method and analyzed by 3D simulation program "Flux". For the prototype linear force motor, the results of the calculated by conventional design method and the analyzed by 3D simulation program are compared with the test result. Finally it is showed that the magnetic circuit revision constant which is found by comparing of the analyzed and the measured data can be used for the design of the voice coil type linear force motor to minimize the trial and error.

• Journal of Drive and Control
• /
• v.11 no.4
• /
• pp.46-52
• /
• 2014

This study suggests a small-sized screw decanter specialized for dredging sites. Generally, conventional screw decanters are composed of a cylinder and a cone. However, the suggested screw decanter simply has a cone based on a cone-type bowl structure. In this research, a commercial analysis tool is used to establish an optimal design for the bowl and the screw conveyor. Moreover, the base frame, where the main bearings that support the spindle of the bowl and the screw conveyor are installed, is optimally designed considering the weight of the rotating body and the deflection caused by the high centrifugal force. Furthermore, the natural frequency range of the spinning body, the bowl and the screw conveyor, is applied to this base frame; it is designed not to correspond to the resonance frequency range and achieves stability as a result. This study suggests an optimal design for the rotating body and the base frame of a screw decanter considering its vibration characteristics. Such a design will prevent overuse of materials and help to reduce the weight and volume-and the price-of a screw decanter.

• Journal of Drive and Control
• /
• v.11 no.4
• /
• pp.25-31
• /
• 2014

This paper details application of a DLC(Diamond Like Carbon)-coating to the swash plate and the ball joint of pistons that make sliding contact with the piston shoes of an axial piston pump. This process, aimed to reduce the frictional and leakage power losses of the hydrostatic piston shoe bearings at the low speed range. At lower speeds than 100rpm, the positive effects of the DLC-coating on the power loss reduction of the hydrostatic piston shoe bearings could be confirmed. These effects resulted in little improvement in volumetric efficiency of the test pump, but the mechanical efficiency could be raised by up to 5% at 100rpm; here, the DLC-coated swash plate played a more dominant role than the DLC-coated ball joint.

• Journal of Drive and Control
• /
• v.10 no.2
• /
• pp.13-22
• /
• 2013

It is difficult to analytically derive a volumetric displacement formula of gerotor hydraulic pump/motor because geometric shape of rotors is complicated. An analytical method about the volumetric displacement is proposed in this work, which is relatively easy and based upon two physical concepts. The first one is energy conservation between hydraulic energy of the pump/motor and mechanical input/output energy. The second concept is torque equilibrium with respect to inner and outer rotors. The formula about the volumetric displacement is derived for the common case of inner and outer rotors rotate with respect to fixed axes. The formula is verified by comparing another analytical displacement formula, and it is numerically verified by comparing numerical results, which is calculated for geometric specification of a motor. The numerical displacement is calculated through CAD software program and MATLAB program. The proposed analytical formula can be utilized in analysis and design of hydraulic gerotor motors.