• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.12
• /
• pp.1249-1255
• /
• 2006

This paper presents a constant power control logic for perfect starting a microtubine in vehicle. Under extremely low temperature, performance of the start-up system is severely dropped than that of room temperature because of increasing of load of mechanical parts including engine core and drop of the lead-acid battery capacity. Unfortunately, performance drop of lead-acid battery makes severe problems that cause a malfunction of fuel and lubrication system and power fail of digital devices. So we propose the new start-up logic by constant output power control of lead-acid battery using PWM inverter controller for preventing above problems and keeping good performance of start-up system for microturbine. Also, we prove usefulness of new start-up logic through experimental results under $-32^{\circ}C$ ambient temperature.

• Journal of Power Electronics
• /
• v.12 no.2
• /
• pp.276-284
• /
• 2012

AC/AC power conversion is widely used to feed AC loads with a variable voltage and/or a variable frequency from a constant voltage constant frequency power grid or to connect critical loads to an unreliable power supply while delivering a very balanced and accurate sinusoidal voltage system of constant amplitude and frequency. The load specifications will clearly impose the requirements for the inverter stage of the power converter, while wider ranges of choices are available for the rectifier. This paper investigates the utilization of a buck-type current source rectifier as the active front-end stage of an AC/AC converter for applications that require an adjustable DC-link voltage as well as elimination of the low-frequency common mode voltage. The proposed solution is to utilize a combination of two or more zero current vectors in the Space Vector Modulation (SVM) technique for Current Sources Rectifiers (CSR).

• Journal of Power Electronics
• /
• v.17 no.6
• /
• pp.1512-1522
• /
• 2017

Switched reluctance motor (SRM) is suitable for electric vehicle (EV) applications with the advantages of simple structure, good overload capability, and inherent fault-tolerance performance. The SRM dynamic simulation model is built based on torque, voltage, and flux linkage equations. The EV model is built on the basis of the analysis of forces acting on a vehicle. The entire speed range of the SRM drive is then divided into constant torque and constant power areas. The command torque of the motor drive system is given according to the accelerator pedal coefficient and motor operation areas. A novel adaptive variable angle control is proposed to avoid the switching chattering between the current chopping control and angle position control modes in SRM drives for EV applications. Finally, simulation analysis and experimental results are conducted to verify the accuracy of the proposed simulation model and control strategy.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.276-280
• /
• 2001

In this paper, an approach to the design of negative impedance stabilizing controllers for PWM DC/DC converters that are used in DC switching. power supplies with constant power loads is presented. The control approach is based on the feedback linearization technique. Because of the negative impedance destabilizing characteristics of constant power loads, classical linear control methods have stability limitations around the operating points. However, the proposed stabilizing technique improves large-signal stability and dynamic responses. The proposed controllers are simulated and their responses under different operations are studied. Stability of the control technique is also verified using the second theorem of Lyapunov.

• Journal of Positioning, Navigation, and Timing
• /
• v.10 no.4
• /
• pp.335-340
• /
• 2021

A constant envelope multiplexing via constellation tailoring scheme is proposed for flexible power allocation of Global Navigation Satellite System (GNSS) signals. The proposed scheme is compared with the coherent adaptive subcarrier modulation (CASM) adopted in the L1 band signals of the Global Positioning System (GPS) in terms of power difference and power loss. Analysis of the constellation optimization results on the power difference and power loss show that the proposed scheme outperforms the CASM of the GPS signals in the allowable power difference of less than 0.1 dB.

• Journal of Communications and Networks
• /
• v.13 no.5
• /
• pp.442-448
• /
• 2011

It's a challenging task to design a high performance modulation for satellite and space communications due to the limited power and bandwidth resource. Constant envelope modulation is an attractive scheme to be used in such cases for their needlessness of input power back-off about 2~3 dB for avoidance of nonlinear distortion induced by high power amplifier. The envelope of Feher quadrature phase shift keying (FQPSK) has a least fluctuation of 0.18 dB (quasi constant envelope) and can be further improved. This paper improves FQPSK by defining a set of new waveform functions, which changes FQPSK to be a strictly constant envelope modulation. The performance of the FQPSK adopting new waveform is justified by analysis and simulation. The study results show that the novel FQPSK is immune to the impact of HPA and outperforms conventional FQPSK on bit error rate (BER) performance. The BER performance of this novel modulation is better than that of FQPSK by more than 0.5 dB at least and 2 dB at most.

• Korean Journal of Optics and Photonics
• /
• v.8 no.2
• /
• pp.116-121
• /
• 1997

The optical power drift due to temperature variation of a laser diode driven by constant voltage is different from one driven by constant current. When a laser diode is driven by constant current, the optical output decreases as the temperature increases because the population inversion decreases. However, When it is driven by constant voltage, injection current increases with temperature rise, which in turn increases the optical power. As the result, the optical power variation reduces. Experimental results show that when these two components are almost equal and cancel each other, the optical power variation coefficient is very small and the optical output is stable.

• Journal of Drive and Control
• /
• v.11 no.4
• /
• pp.53-60
• /
• 2014

This paper proposes a control scheme to reduce the power consumption of a variable displacement swash-plate type piston pump supplying oil to a valve-controlled hydraulic cylinder at constant pressure. Whenever flow rate demand was absent, the swash plate angle and the pump speed were changed to the minimum values required to compensate for the internal leakage flow. In response to command signals, the pump speed was changed in proportion to the absolute mean value of the speed component for position commands. At the same time, a pressure regulator was activated to maintain constant system pressure by precisely adjusting the pump speed with the swash plate angle fixed at the maximum. The conventional system consisting of a pressure-compensated variable displacement type pump is driven at a constant speed of 1,800rpm. By comparison, computer simulation and experimental results showed that idling power at stand-by status could be reduced by up to 70% by reducing the pump speed from 1,800rpm to 300rpm and the swash plate angle to the minimum.

• ETRI Journal
• /
• v.34 no.3
• /
• pp.470-473
• /
• 2012

In this letter, the constant driving power reduction ratio has been achieved for column drivers regardless of the input image by incorporating a new static power reduction scheme into the previous dynamic power reduction method. The measured power reduction ratio is around 50% for a 120 Hz liquid crystal display panel in such cases of still input video and fallback.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.4
• /
• pp.79-87
• /
• 2004

The light pattern reflected from a machined surface contains some information like roughness and profile on the projected surface as expected in the Beckmann-Spizzichino model. In applying the theory into a real reliable measuring device, many parameters such as incident light power, wave length, spot size should be kept a constant optical value. However, the reflected light power is likely to change with the environmental noise, the variations of the light source, the reflectivity of the surface, etc. even though the incident light power is constant. In this study, a method for adjusting the incident light power to keep the reflected light power projected on a CMOS image sensor constant was proposed and a simple adjustment algorithm based on PI digital control was examined. Experiments verified that the proposed method made the surface roughness measurement better and more reliable even under variations of the height of light source.