• Journal of Environmental Science International
• /
• v.31 no.4
• /
• pp.295-309
• /
• 2022

The purpose of this study was to evaluate the operational characteristics of wastewater treatment using Sequencing Batch Reactor (SBR) with Aerobic Granular Sludge (AGS) separator in the pilot plant. Pilot plant experiments were conducted using SBR with AGS separator and pollution removal efficiencies were evaluated based on the operational condition and surface properties of AGS. The results of the operation on water quality of the effluent showed that the average concentration of total organic carbon, suspended solids, nitrogen, and phosphorus was 6.89 mg/L, 7.33 mg/L, 7.33 mg/L, and 0.2 mg/L, respectively. All these concentrations complied the effluent standard in Korea. The concentration of mixed liquor suspended solid (MLSS) fluctuated, but the AGS/MLSS ratio was constant at 86.5±1.3%. Although the AGS/MLSS ratio was constant, sludge volume index improved. These results suggested that the particle discharged fine sludge and increased the AGS praticle size in the AGS. Optical microscopy revealed the presence of dense AGS at the end of the operation, and particles of > 0.6 mm were found. Compared to those of belt-type AGS separator, the required area and power consumption of the hydrocyclone-type AGS separator were reduced by 27.5% and 83.8%, respectively.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.187-193
• /
• 2021

In order to solve the problem of false terrains caused by environmental interferences and tunneling effect in the conventional multi-beam seafloor terrain detection, this paper proposed a seafloor topography detection method based on fast two-dimensional (2D) Censored Mean Level Detector-statistics Constant False Alarm Rate (CMLD-CFAR) method. The proposed method uses s cross-sliding window. The target occlusion phenomenon that occurs in multi-target environments can be eliminated by censoring some of the large cells of the reference cells, while the remaining reference cells are used to calculate the local threshold. The conventional 2D CMLD-CFAR methods need to estimate the background clutter power level for every pixel, thus increasing the computational burden significantly. In order to overcome this limitation, the proposed method uses a fast algorithm to select the Regions of Interest (ROI) based on a global threshold, while the rest pixels are distinguished as clutter directly. The proposed method is verified by experiments with real multi-beam data. The results show that the proposed method can effectively solve the problem of false terrain in a multi-beam terrain survey and achieve a high detection accuracy.

• Nuclear Engineering and Technology
• /
• v.53 no.1
• /
• pp.304-313
• /
• 2021

Nickel base Alloy X-750, which is used as fastener parts in light-water reactor (LWR), has experienced many failures by environmentally assisted cracking (EAC). In order to improve the reliability of passive components for nuclear power plants (NPP's), it is necessary to study the failure mechanism and to predict crack growth behavior by developing a probabilistic failure model. In this study, The Bayesian inference was employed to reduce the uncertainties contained in EAC modeling parameters that have been established from experiments with Alloy X-750. Corrosion fatigue crack growth rate model (FCGR) was developed by fitting into Paris' Law of measured data from the several fatigue tests conducted either in constant load or constant ΔK mode. These parameters characterizing the corrosion fatigue crack growth behavior of X-750 were successfully updated to reduce the uncertainty in the model by using the Bayesian inference method. It is demonstrated that probabilistic failure models for passive components can be developed by updating a laboratory model with field-inspection data, when crack growth rates (CGRs) are low and multiple inspections can be made prior to the component failure.

• Journal of the Korean Vacuum Society
• /
• v.7 no.s1
• /
• pp.106-117
• /
• 1998

Fluorocarbonated-SiO2 films were deposited on p-type Si(100) substrate using FSi$(OC_2H_5)_3$ (FTES), and $O_2$ mixture gases by a helicon plasms source. High density $O_2$/FTES/Ar plasma of ~$10^{12} \textrm{cm}^{-3}$ is obtained at low pressure (<3mTorr) with RF power above 900 W in the helicon plasma source. Optical emission spectroscopy (OES) is used to study the relation between the relative densities of the radicals and the film properties. The FTES and $O_2$ gases are greatly dissociated at the helicon mode that is launched at the above threshold plasma density. FTIR and XPS spectra shows that the film has Si-F, and C-F bonds during the formation process of the film which may lower the dielectric constant greatly. The relative dielectric constant, leakage current density, and dielectric breakdown voltage are about 2.8, $8\times10^{-9}\textrm{A/cm}^2$, and > 12 MV/cm, respectively.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2003.05a
• /
• pp.53-53
• /
• 2003

Plasma polymerized organic thin films were deposited on Si(100) glass and metal substrates using thiophene and ethylcyclohexane precursors by PECVD method. In order to compare electrochemical properties of the as-grown thin films, the effects of the RF plasma power in the range of 30~100 W. AFM showed that the polymer films with smooth surface and sharp interface could be grown under various deposition conditions. Impedance analyzer was utilized for the determination of I-V curve for leakage current density and C-V for dielectric constants, respectively. To obtain C-V curve, we used a MIM structure of metal(Al)-insulator(plasma polymerized thin film)-metal(Pt) structure. Al as the electrode was evaporated on the thiophene films that grew on Pt coated silicon substrates, and the dielectric constants of the as-grown films were then calculated from C- V data measured at 1MHz. From the electrical property measurements such as I-V and C-V characteristics, the minimum dielectric constant and the best leakage current of thiophene thin films were obtained to be about 3.22 and $1{\;}{\times}10^{-11}{\;}A/cm^2$. However, in case of ethylcyclohexane thin films, the minimum dielectric constant and the best leakage current were obtained to be about 3.11 and $5{\;}{\times}10^{-12}{\;}A/cm^2$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.3
• /
• pp.255-260
• /
• 2023

In order to spread LED lighting, LED lighting technology directly driven by alternating current (AC) commercial power has recently been introduced. Since current does not flow at a voltage lower than the threshold voltage of the LED, a non-conductive section occurs in the current waveform, and the higher the threshold voltage of the LED, the more discontinuous current waveforms are generated. In this paper, multi-LED modules are connected in series so that the threshold voltage can be adjusted according to the number of LED modules. A small number of LED modules are driven at a low instantaneous rectified voltage, and a large number of LED modules are driven at a high instantaneous rectified voltage to lengthen the overall lighting time of AC-LED lighting, thereby minimizing the luminance deviation of AC-LED lighting. In addition, the load current flowing through the LED module is adjusted to be the same as the design current even at the maximum rectified voltage higher than the design voltage, so that the light brightness of the LED module is kept constant. Therefore, even if the rectified voltage applied to the LED module changes, the AC-LED lighting in which the light brightness is constant and the luminance deviation is minimal has been realized.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.11
• /
• pp.69-76
• /
• 1997

The rotating bending fatigue tests were performed using the specimens taken from Cr-Mo-V steel, widely sued in thermal power plant turbines, at various temperatures such as room temperature, 300 .deg. C, 425 .deg. C and 550 .deg. C. The characteristics of fatigue crack propagation were examined and analyzed by using fracture mechanics parameter. The plastic replica method was also applied in order to measure the crack length on the basis of serial observation of fatigue crack propagation behavior on the defected specimen surface. The fatigue crack propagation behavior of Cr-Mo-V steel was investigated within the frame work of elastic-plastic fracture mechanics. The propagation law of fatigue crack is obtained uniquely by using the term .sigma. $^{n}$ sub a/where .sigma. $_{a}$ is the service stress, a is the crack length and n is a constant. The values of constant n are nearly equal to 2.48, 2.60 and 8.61 at room temperature, 300 .deg. C and 425 .deg. C.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.6
• /
• pp.629-634
• /
• 2010

Natural gas is a promising alternative fuel that can be used to satisfy the strict engine emission regulations in many countries. To develop natural-gas engines, low emission, efficient fuel consumption, and increased power ratings have to be realized. In this study, a cylindrical constant-volume combustion chamber (CVCC) was used to investigate natural-gas combustion characteristics for different prechamber design parameters and equivalence ratios. In particular, the maximum combustion pressure and mass fraction of the burned gas were evaluated by considering orifice diameter, volume ratio of prechamber and equivalence ratio. Using this result and by analyzing the changes in combustion characteristics with variations in design parameters, the optimum prechamber parameters were determined.

• Journal of Microbiology and Biotechnology
• /
• v.16 no.12
• /
• pp.1890-1896
• /
• 2006

Lumostatic operation for cultivation of Haematococcus pluvialis was assessed to test the scale-up strategy of photobioreactors. Lumostatic operation is a method of maintaining a proper light condition based on the specific light uptake rate ($q_e$), by cells. Lumostatic operations were performed in 0.4-, 2-, 10-, and 30-1 scale bubble column photobioreactors and the results were compared with cultures illuminated with constant light intensity. Significant differences were observed in the maximal cell concentrations obtained from 0.4-, 2-, 10-, and 30-1 scale photobioreactors under constant light intensity, yielding the maximal cell concentrations of $2.8{\times}10^5$, $2.2\times10^5$, $1.5\times10^5$, and $1.1\times10^5$ cells/ml, respectively. The maximal cell concentration in a 0.4-1 photobioreactor under lumostatic operation was $4.3\times10^5$ cells/ml. Furthermore, those in 2-, 10-, and 30-1 scale photobioreactors were about the same as that in the 0.4-1 photobioreactor. The results suggest that lumostatic operation with proper $q_e$ is a good strategy for increasing the cell growth of Haematococcus pluvialis compared with a constant supply of light energy. Therefore, lumostatic operation is not only an efficient way to achieve high cell density cultures with minimal power consumption in microalgal cultures but it is also a perfect parameter for the scale-up of photobioreactors.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.10
• /
• pp.858-869
• /
• 2014

Most of the aerospace propulsion is based on the Brayton cycle, in which the combustion is held through the constant pressure process, but further improvement of performance by increasing compression ratio is challenged by mechanical limits. Detonation propulsions, regarded promising for high-speed propulsion for a lase decade, is more rigorously studied in these days as a game-changer for the improvement of thermodynamic efficiency of propulsion and power generation systems. Since, the additional compression by the strong shock of the detonation wave is considered increasing thermodynamics efficiency that is hardly achievable by the conventional compression systems. Present paper will give an introduction the latest technical trends on the Pulse Detonation Engines(PDEs) and the activities on the Pressure Gain Combustion (PGC) based on Constant Volume Combustion (CVC).