• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2007년도 춘계학술논문 발표대회
• /
• pp.141-145
• /
• 2007

The part in the structure that is most affected by changes of external temperature is the protective concrete layer that protects a waterproofing layer. Also, the waterproofing layer that is situated under or on the back of such a protective concrete layer is affected by temperature and the behavior of the protective concrete layer under the condition of consolidation or close adhesion. In particular, in many cases, the damage is serious mainly around the projection (such as a parapet), crack, and joint (expansion joint). However, there is no proper way of examining again the non-exposed waterproofing layer once it has been constructed. Therefore, there is an assessment only on the physical property of materials and the capability of the layer in construction, and there is no actual assessment in consideration of its environmental condition or the condition of the use of buildings after construction. Therefore, in order to create more pleasant buildings and to enhance the durability of structures, this study conducts research into the change of capability of non-exposed waterproofing material after the application of a static load and moving load on the waterproofing layer situated under or on the back of protective concrete.

• 한국재료학회지
• /
• 제21권10호
• /
• pp.542-545
• /
• 2011

Half-Heusler alloys are a potential thermoelectric material for use in high-temperature applications. In an attempt to produce half-Heusler thermoelectric materials with fine microstructures, TiCoSb was synthesized by the mechanical alloying of stoichiometric elemental powder compositions and then consolidated by vacuum hot pressing. The phase transformations during the mechanical alloying and hot consolidation process were investigated using XRD and SEM. A single-phase, half- Heusler allow was successfully produced by the mechanical alloying process, but a minor portion of the second phase of the CoSb formation was observed after the vacuum hot pressing. The thermoelectric properties as a function of the temperature were evaluated for the hot-pressed specimens. The Seebeck coefficients in the test range showed negative values, representing n-type conductivity, and the absolute value was found to be relatively low due to the existence of the second phase. It is shown that the electrical conductivity is relatively high and that the thermal conductivities are compatibly low in MA TiCoSb. The maximum ZT value was found to be relatively low in the test temperature range, possibly due to the lower Seebeck coefficient. The Hall mobility value appeared to be quite low, leading to the lower value of Seebeck coefficient. Thus, it is likely that the single phase produced by mechanical alloying process will show much higher ZT values after an excess Ti addition. It is also believed that further property enhancement can be obtained if appropriate dopants are selectively introduced into this MA TiCoSb System.

• 한국분말재료학회지
• /
• 제14권4호
• /
• pp.251-255
• /
• 2007

This work is to report not only the effect of rapid solidification of $MgZn_{4.3}Y_{0.7}$ alloys on the micro-structure, but also the extrusion behavior on the materials properties. The average grain size of the atomized powders was about $3-4{\mu}m$. The alloy powders of $Mg_{97}Zn_{4.3}Y_{0.7}$, consisted of I-Phase (Icosahedral, $Mg_{3}Zn_{6}Y_{1}$) as well as Cubic structured W-Phase ($Mg_{3}Zn_{3}Y_{2}$), which was finely distributed within ${\alpha}-Mg$ matrix. The oxide layer formed along the Mg surface was about 48 nm in thickness. In order to study the consolidation behavior of Mg alloy powders, extrusion was carried out with the area reduction ratio of 10:1 to 20:1. As the ratio increased, fully deformed and homogeneous microstructure could be obtained, and the mechanical properties such as tensile strength and elongation were simultaneously increased.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 봄 학술논문 발표대회
• /
• pp.90-91
• /
• 2020

As the construction site has become narrower recently, the importance of mass concrete is naturally being highlighted as skyscrapers become popular. However, it is not possible to install the entire volume per day if the mass concrete is installed due to the Remicon 8⦁5 system and the 52-hour workweek system. When the mass concrete base is divided into several days, cold joints occur because the consolidation of joints is not integrated due to different degree of hardening in the case of the previous layer and the next day. As a result, existing research has shown that if super retarding agent are mixed into Ready Mixed Concrete (hereinafter referred to as Remicon) using sugar as a raw material to delay the curing time of concrete, cold joints are inhibited and cracks are inhibited by reducing the initial hydration heat.

• Geomechanics and Engineering
• /
• 제31권3호
• /
• pp.291-304
• /
• 2022

Maximum shear modulus (G_max or G₀) is an important soil property useful for many engineering applications, such as the analysis of soil-structure interactions, soil stability, liquefaction evaluation, ground deformation and performance of seismic design. In the current study, bender element (BE) tests are used to evaluate the effect of the void ratio, effective confining pressure, grading characteristics (D₅₀, C_u and C_c), anisotropic consolidation and initial fabric anisotropy produced during specimen preparation on the G_max of sand-gravel mixtures. Based on the tests results, an empirical equation is proposed to predict G_max in granular soils, evaluated by the experimental data. The artificial neural network (ANN) and Adaptive Neuro Fuzzy Inference System (ANFIS) models were also applied. Coefficient of determination (R²) and Root Mean Square Error (RMSE) between predicted and measured values of G_max were calculated for the empirical equation, ANN and ANFIS. The results indicate that all methods accuracy is high; however, ANFIS achieves the highest accuracy amongst the presented methods.

• 보존과학회지
• /
• 제32권3호
• /
• pp.353-364
• /
• 2016

구리 현릉의 능상석조물은 주로 자철석계열의 흑운모화강암으로 구성되었으며 풍화도가 높다. 손상 특성으로는 미생물 및 토사 유입과 흑색오염물의 발생률이 높게 나타났다. 봉분 부재에 대한 손상도 평가 결과, 토사(50.5%)와 지의류(47.6%)의 피도가 주요 요인으로 나타났으며 북면에서 지의류 외의 생물생육(8.6%)이 두드러진다. 표면오염물은 광물산화와 부재간 이음부에서 석고가 생성되었고 주요 변색양상인 흑색은 유기물에 의한 것으로 해석되었다. 각 단위 부재별 초음파 측정 결과, 평균 2,195 m/s의 속도로 심한풍화(HW)가 진행된 상태이며 대부분 부재에서 4~5등급에 도시되었다. 따라서 현릉의 능상석물에 대한 보존처리가 필요한 상태로 판단된다. 훼손을 촉진하는 토사 및 높은 점유율을 보이는 지의류 등 생물오염 세척과 상당한 풍화가 진행된 부재에 대한 강화 및 접합 충전이 요구된다. 또한 Ca를 주성분으로 하는 보수물질과 백화에 대한 제거 및 재처리 여부에 대한 논의가 필요하다 .

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제13권1호
• /
• pp.13-23
• /
• 2008

오염물질로 오염된 퇴적점토의 강도, 변형 및 투수특성 변화를 파악하기 위하여 NaCl 수용액과 매립장 침출수를 시료의 간극수(포화수)로 교체하여 삼축압축시험과 압밀시험을 수행하였다. 또한, 채취된 점토시료의 화학적 특성을 규명하기 위하여 주사전자현미경(SEM) 관찰과 에너지분산분광(EDX) 분석이 수반된다. 화학성분 분석결과 O, C, Si, Al, Fe 크기 순의 구성비가 얻어졌으며, 삼축압축시험 및 압밀시험결과는 NaCl의 농도가 증가할수록 극한응력(강도)은 증가하고 압축성과 투수성이 커지는 경향을 보이는데, 이는 전해질의 농도가 증가할수록 확산이중층(DDL)의 두께가 감소되어 면모화되기 때문인 것으로 판단된다. 또한, 점토 차수재를 투과한 침출수가 지하수 오염에 미치는 영향을 분석하기 위하여 MT3D 해석모델이 이용되었으며, 지하수 오염거동 해석결과 초기 염소이온 농도가 클수록 측정농도도 커지며, 시간경과에 따라 지하수 오염농도는 비선형적으로 증가되었다. 지하수 오염농도 감쇄 관계식을 유도하여 지하수 오염 이동거리를 예측한 결과, 초기농도가 클수록 지하수 오염 이동거리도 크게 나타났다.

• 한국지반공학회논문집
• /
• 제15권1호
• /
• pp.151-160
• /
• 1999

광양만의 해저에서 채취한 점성토시료의 물리적 성질과 역학적 특성을 규명하기 위한 일련의 실내시험을 수행하였다. 주요 시험내용은 제반 물리적 성질시험, 표준압밀시험, 비배수 및 배수 삼축시험(CIU, CID) 등이다. 통일분류에 의하면 CL, CH로 구분되는 광양만 점토는 자연함수비, 38.3~84.6%, 액성지수, 0.71~0.98 이고 과압밀비가 1.06~l.60인 실질적인 정규압밀상태라고 볼 수 있다. 비배수 삼축시험에서의 유효응력경로는 (q, p)공간에서 등방압밀응력($p_0$) 으로 규준화되고, 등 전단변형률선은 원점을 통과하며 선형적이다. 비배수 전단변형률($\varepsilon$)은 응력비($\eta$) 만의 함수이고, ($\varepsilon/\eta, \eta$) 공간에서 절편값을 갖는 직선으로 나타났다. 또한, 등방압밀응력으로 규준화된 간극수압도 응력비에 대하여 직선이고, 그 구배, C는 간극수압 매개변수로 정의될 수 있다. 이상에서 기술된 경향을 근거로 하여 비배수 응력경로 및 전단변형률을 예측할 수 있는 계산식을 제안하였고, 제안식에 의하여 계산된 응력경로와 전단변형률은 기존의 Cam-clay이론 보다 실측치에 더 가까운 값을 주는 것으로 나타났다. 배수시험 결과에서 얻어진 응력경로 상의 파괴점은 비배수 응력경로의 한계상태선과 동일 선상에 위치하며, 이 사실은 한계상태이론의 기본 개념과 일치한다.

• 펄프종이기술
• /
• 제34권5호
• /
• pp.1-17
• /
• 2002

The immobilization and consolidation of the model coatings based on the plastic pigment and latex binder of known particle sizes were theoretically Studied in terms of the dense random packing of binary spheres and varying extent of latex film shrinkage. The porosity of the model coatings was calculated based on three proposed latex shrinkage models: Maximum, Minimum, and Linearly Decreasing Latex Shrinkage. The increasing extent of latex shrinkage was calculated up to the critical pigment volume concentration(CPVC) as a function of plastic pigment volume fractions, and the maximum latex shrinkage was estimated from the CPVC. Also, the number of pores and the average equivalent spherical pore diameters were calculated based on those proposed models. The opacity and gloss of the model coatings on polyester films were measured and their porosity was also determined by a simple coat weight-thickness method. As expected, various coating structure-property-composition relationships, such as opacity, gloss, porosity, etc., were shown to exhibit sharp transitions near the CPVC. The CPVC values determined by the opacity, gloss, and porosity vs. PVC relationships, respectively, agreed very well with each other. Especially, the CPVC's determined by the opacity and porosity vs. PVC curves were identical. The comparison between the theoretically calculated and experimental porosity values showed that the intermediate value between the maximum and minimum latex shrinkage would best fit the experimental porosity data. The effect of plastic pigment particle size on the optical properties and porosity of model coatings was also studied and it was observed that the coating opacity and porosity increased with increasing plastic pigment particle size, but the gloss decreased. The ink gloss of the uncalendered model coatings applied onto commercial sheet offset coated papers was shown to be affected by both the coating gloss and porosity: the higher the coating gloss, the higher the ink gloss, but the higher the coating porosity, the lower the ink gloss. Their printability was also studied in terms of the number of passes-to-fail and the rate of ink setting as a function of both plastic pigment volume fractions and plastic pigment particle sizes. A minimum crack-free temperature(MCR) of latex-bound coatings was proposed to better predict the behaviors of latexes as coating binders. The wet state of model coating dispersions, the surfaces of consolidated model coatings, and their internal structure were examined by both electron and atomic force microscopy, and their micrographs were found to be consistent with our immobilization and consolidation models.

• Geomechanics and Engineering
• /
• 제22권3호
• /
• pp.227-236
• /
• 2020

Expansive soils are renowned for their swelling-shrinkage property and these volumetric changes resultantly cause huge damage to civil infrastructures. Likewise, subgrades consisting of expansive soils instigate serviceability failures in pavements across various regions of Pakistan and worldwide. This study presents the use of polypropylene fibers to improve the engineering properties of a local swelling soil. The moisture-density relationship, unconfined compressive strength (UCS) and elastic modulus (E₅₀), California bearing ratio (CBR) and one-dimensional consolidation behavior of the soil treated with 0, 0.2, 0.4, 0.6 and 0.8% fibers have been investigated in this study. It is found that the maximum dry density of reinforced soil slightly decreased by 2.8% due to replacement of heavier soil particles by light-weight fibers and the optimum moisture content remained almost unaffected due to non-absorbent nature of the fibers. A significant improvement has been observed in UCS (an increase of 279%), E₅₀ (an increase of 113.6%) and CBR value (an increase of 94.4% under unsoaked and an increase of 55.6% under soaked conditions) of the soil reinforced with 0.4% fibers, thereby providing a better quality subgrade for the construction of pavements on such soils. Free swell and swell pressure of the soil also significantly reduced (94.4% and 87.9%, respectively) with the addition of 0.8% fibers and eventually converting the medium swelling soil to a low swelling class. Similarly, the compression and rebound indices also reduced by 69.9% and 88%, respectively with fiber inclusion of 0.8%. From the experimental evaluations, it emerges that polypropylene fiber has great potential as a low cost and sustainable stabilizing material for widespread swelling soils.