• The Journal of Engineering Geology
• /
• v.34 no.3
• /
• pp.447-457
• /
• 2024

This study investigated a cut-slope surface containing Tertiary faults, representing a conical-shaped slope with strike varying from N44°E to NS, N50°W, and finally N70°E. The slope consists mainly of basalt, with discontinuities in the slope including faults, fault zones, fracture zones, shear joints, and extension joints. The type and scale of failure vary with the strike of the slope and the strikes of discontinuities, with plane and wedge failure predominating. Based on face-mapping data, SMR (slope mass rating), rock physical and mechanical properties, analysis of stereonet projections and geological cross-sections, and critical equilibrium analysis, optimal slope stability determination was found to involve the countermeasure method, the slope gradient relief method, the green soil surface treatment method, and a fall prevention measure. After application of the countermeasure method, both dry and wet slope conditions exceeded allowable safety factors. It is expected that the preparation of geological cross-sections of various representative sections perpendicular to the surface of the slope, and the application of corresponding countermeasure methods, will be reasonable tools for three-dimensional analysis of slope stability. If the strike of the slope varies widely, it is necessary to prepare geological cross-sections, and the section used for critical equilibrium analysis must be established as the basic section.

• Geomechanics and Engineering
• /
• v.38 no.4
• /
• pp.367-380
• /
• 2024

In this study, a prediction model for the cutting force evolution in brittle rocks was developed. This model is based on indentation tests using a conical pick at a cutting depth of 9 mm. The behavior of the indentation mechanism was analyzed in three phases by using Evans' cutting mode. The peak values in the force history identified these phases. The variation in the local strength of the rock caused a large offset in the model prediction of chipping. Regression analyses showed that there is a strong power relationship between the upper bound of the cutting force along with chipping and depth of cut. The slope of the three crushing phases has been found to increase sequentially (α₁<α₂<α₃). In addition, a positive correlation existed between the Schmidt hardness and brittleness index that affects the lower and upper bounds of chipping. Consequently, the results clearly demonstrate that the new model can reasonably predict the evolution of the cutting force based on experimental data. These results would be beneficial for engineers to design and select the optimum excavation machine to reduce mechanical vibration and enhance cutting efficiency.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.4
• /
• pp.344-351
• /
• 2012

A disc spring consists of a conical disc. A load-displacement formula was newly developed in the form of energy method to consider both rigid and friction. The cross section of the disc spring has identical slope angles at the bottom of conical. To solve such a problem, an energy method calculation is proposed. To achieve the goal of this study, the proposed calculation is extended to a disc spring with friction. A firm basis background study based on Almen's work is presented in developing a new numerical approach to predict the available formulation for a disc spring with friction.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.572-577
• /
• 2011

A disc spring consists of a conical disc. A load-displacement formula was newly developed in the form of energy method to consider both rigid and friction. The cross section of the disc spring has identical slope angles at the bottom of conical. To solve such a problem, an energy method calculation is proposed. To achieve the goal of this study, the proposed calculation is extended to a disc spring with friction. A firm basis background study based on Almen's work is presented in developing a new numerical approach to predict the available formulation for a disc spring with friction.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.27 no.2
• /
• pp.173-182
• /
• 1994

A numerical experiment on the effective discharge of waste materials caused in recirculating aquaculture basins was performed. The numerical model used in this study was a 4-level hydrodynamic and advection-diffusion model. Flow structures and settling processes of ss in the various mathematical model basins are discussed. The calculated flow fields of the numerical basin corresponded well with the measured velocity in field basin. In the cases of steep bottom slopes in 4/30, the non-dimensional tractive force($U{\ast}/U{\ast}_c$) which is all important parameter for the deposition pattern of waste materials was stronger than with the mild slope one. The settling pattern of ss depended considerably on the degree of bottom slope of basin. To concentrate deposited waste materials into the center discharge pipe, it is useful to design a cylindrical basin with a steeply conical bottom. In addition, to prevent movement of the deposit area away from the center, it is necessary to locate the circulating ducts at diametrically opposed points on the basin sides.

• Journal of the Korean Society of Safety
• /
• v.21 no.1 s.73
• /
• pp.114-119
• /
• 2006

In this study, laminated composite umbrella type roofs structures such as stadium, exhibition, auditorium and museum are analyzed. These structures have not been dealt with so far because of the difficulty in modeling. These have been analyzed mostly by a simplified method or a grid analysis in design. In this study, better results can be obtained by using shell element. The behavior of umbrella type shell roof under self weight is analyzed for various parameters such as the influence of diaphragm, diaphragm type, ${\gamma}-angle$ type, height/chord ratio of segment, slope of roofs, number of conical segment and subtended angle.

• Advances in aircraft and spacecraft science
• /
• v.10 no.5
• /
• pp.457-471
• /
• 2023

The paper evaluates the aerodynamic coefficients on a blunt-nose re-entry capsule with a conical cross-section followed by a cone-flare body. A computer code is developed to solve three-dimensional compressible inviscid equationsfor flow over a Space Recovery Experiment (SRE) configuration at different flare-cone half-angle at Mach 6 and angle of attack up to 5°, at 1° interval. The surface pressure variation is numerically integrated to obtain the aerodynamic forces and pitching moment. The numerical analysis reveals the influence of flare-cone geometry on the flow characteristics and aerodynamic coefficients. The numerical results agree with wind tunnel results. Increase of cone-flare angle from 25° to 35° results in increase of normal force slope, axial forebody drag, base drag and location of centre of pressure by 62.5%, 56.2% and 33.13%, respectively, from the basic configuration ofthe SRE of 25°.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.2
• /
• pp.105-118
• /
• 2008

The newly developed analysis method for nanoindentation load-displacement curves are focused on not only obtaining elastic modulus and hardness values but also other mechanical properties, such as yield strength and strain hardening properties. Dao et al. developed a forward and reverse algorithm to extract the elasto-plastic properties of materials from the load-displacement curves obtained in nanoindentation test. These algorithms were only applicable for engineering metals (Poisson#s ratio 0.3) using the equivalent conical indenter of the Berkovich. However, the applicable metals are substantially limited because range of used in the finite element analysis is narrow. This study is designed to expand range of the applicable metals in the reverse algorithms established by Dao et al. and to improve the accuracy of that for extracting the elasto-plastic properties of materials. In this study, a representative strain was assumed to vary according to specific range of $E^*/{\sigma}_r$ and was defined as function of $E^*/{\sigma}_r$. Also, an initial unloading slope in reverse algorithms improved in this study was not considered as independent parameters of the load-displacement curves. The mechanical properties of materials for finite element analysis were modeled with the elastic modulus, E, the yield strength, ${\sigma}_y$, and the strain hardening exponents, n. We showed that the representative strain (0.033) suggested by Dao et al. was no longer applicable above the $E^*/{\sigma}_r$ of 400 and depended on values of $E^*/{\sigma}_r$. From these results, we constructed the dimensionless functions, in where the initial unloading slope was not included, for engineering metals up to $E^*/{\sigma}_r$ of 1500. These functions allow us to determine the mechanical properties with greater accuracy than Dao#s study.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.17 no.1
• /
• pp.15-23
• /
• 1984

Difference of the entering and the escaping behaviour of shrimp(Palaemon pacificus) to the model traps were observed in accordance with netting materials, baits, type of traps and slope of flapper, and gathering responses were also investigated on the odour of bait extracts in the aquarium as the preliminary test. In order to investigate the difference in catch according to type and structure of traps those designated from A to E were made of iron frames and nettings. The type A was a conical shape with two entrances at its both sides and the others were square piller shape with one entrance at their upper surface(type B) or two entrance at their both ends(type C, D and E). However th type D and E were connected with flapper and the thye E was made by attaching iron frames of same height under the type D. The traps were prepared 10 each and so a total of 50 traps were used in the experiment at sea. The main species caught was Charybdis japonica, but Astroconger myriaster was also caught fairly. The catches of these species were significant in difference between the types of traps. That is, Charybdis japonica was caught more in type A, C and D than others and less in type B and E, and Astroconger myriaster was caught more in type A and D and less in type B and E. However the catch of Astroconger myriaster in type C, even if less than that in type A showed no significant difference with the other traps. The total catch of Charybdis japonica and Astroconger myriaster was almost same in order with the catch of Charybdis japonica. The type B and E seemed to be difficult in entering of fishes into them. However, the type A and C seemed to be easy not only in entering, but also in escaping. Especially, the type C showed more escaping. On the other hand, the type D seemed to be not so easy in entering of fishes as type A and C, but very difficult in escaping. Consequently, the escaping of fishes from the traps seemed to be more difficult in conical traps than any other traps. The catches might be influenced by the bait with bag compare to without bag and also the immersed time of traps into water for fishing.