• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.15 no.4
• /
• pp.24-31
• /
• 2019

In this paper, we simulated a new apartment building by using radon emission test values from various building materials used as interior finishing materials. The simulations evaluated the radon concentration in the room according to the radon emissions and the ventilations for each type of finishing material (gypsum board, stone, tile and concrete). Overall concrete finish simulation case showed the highest concentration than the case using other materials due to the effect of wall area at the center of each room and the mean radon concentration at 1.5 m above the floor was slightly lower than the mean value at each center. In the case of the porch, pantry and bathroom, the radon concentration was high even when the same materials were used as in the other rooms.

• Proceedings of the KSR Conference
• /
• 2003.05a
• /
• pp.343-348
• /
• 2003

As one of countermeasures for vibration and noise source which come from train operation in subway system, the heavy-weighted tunnel structure and the low-vibration track design have been adopted. In recent the low-vibration concrete track have been constructed to enhance the maintenance effectiveness as well as the reduction of vibration. This paper is explaining and evaluating of the characteristics of vibration and its effects comparing to tile ballast track, concrete track, and full surface supported floating slab track installed on Express bus terminal in Seoul subway No. 7 line.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2011.05a
• /
• pp.31-32
• /
• 2011

The purpose of this study is to investigate the amount of chloride penetration into concrete finishing materials. Chloride ion migration test was used rapid infiltration method proposed by 'NT-Build 492'. The kind of coated finishing material is 'None-finished(N)', 'Cement Mortal(M)', 'Water based paint(P)', 'Bone-Tile(B)', 'Repair Mortal(R1)' in this paper.

• Journal of the Korea Concrete Institute
• /
• v.13 no.6
• /
• pp.602-609
• /
• 2001

A strut-and-tie model was proposed to predict the shear strength of RS beam which is a hybrid steel beam with reinforced concrete ends. The proposed model is capable of considering the concrete softening effects due to diagonal shear cracks at the embedded area of steel in concrete. It can predict tile failure strength of RS beam from the mathematical formulations which are based on equilibrium, compatibility, and the constitutive laws of cracked reinforced concrete. The previous experimental results of 15 RS beams were analyzed with the proposed model and the analytical results were also compared with formulas currently available. The comparison revealed that the proposed model can predict the strength of RS beam better than the others. The average ratio of experimental strengths to analytical results was 1.02 and the standard deviation was 0.126.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.15 no.3
• /
• pp.3096-3106
• /
• 1973

As a link in the chain of antidrought measure, our attempt is made to obtain basic informations on the construction of an infiltration gallary which can be supplied with irrigation water by catching of underground water in small river beds, which is economical, permanent and efficient. The experiment was made, concerning the structure of catchment conduits, by constructing a model sand tank $1.5m{\times}5m{\times}1.5m$ in dimension made of reinforced concrete. Various kinds of measuring equipment were attached to the model tank which contains a set of catchment conduits, each of them was made 30cm in diameter and 60cm in length with the ratio of sectional area to total area of influx holes 10:1, 20:1, 30:1. The average size of influx holes was fixed from 0mm to 10mm, 20mm and 30mm in diameter respectively. Obtained results are as follow; (a) In view of the water catchment capacity, manufacturing cost and the antipressure strength of the catchment conduits, it is the best method to decide the total number of influx holes 20 per sq. meter of each tile surface, and the size of influx holes 20mm in diameter, when the conduits have diameter less than 1m. (b) The greatest factor of safety against external load is to arrange the influx holes in a zigzag manner on the tile surface. The most effective formula of arrangement is $S{\geqq}\sqrt{2gd}$ where: s : spacing of opening row. g : spacing of opening line. d : diameter of influs hole.

• Journal of Environmental Science International
• /
• v.24 no.9
• /
• pp.1131-1138
• /
• 2015

Radon exhalation rates have been determined for samples of concrete, gypsum board, marble, and tile among building materials that are used in domestic construction environment. Radon emanation was measured using the closed chamber method based on CR-39 nuclear track detectors. The radon concentrations in apartments of 100 households in Seoul, Busan and Gyeonggi Provinces were measured to verify the prediction model of indoor radon concentration. The results obtained by the four samples showed the largest radon exhalation rate of $0.34314Bq/m^2{\cdot}h$ for sample concrete. The radon concentration contribution to indoor radon in the house due to exhalation from the concrete was $31.006{\pm}7.529Bq/m^3$. The difference between the prediction concentration and actual measured concentration was believed to be due to the uncertainty resulting from the model implementation.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.33 no.3
• /
• pp.317-331
• /
• 2023

Objectives: Construction workers are exposed to various hazardous substances simultaneously. However, little is known about the exposure hazards in construction industry. This study was aimed at identifying the risk of exposure hazards among construction workers. Methods: The expert survey (n=29) was conducted, including construction industry health managers (n=11) and work environment monitoring experts (n=18), on exposure probability, intensity and risk of hazardous substances by construction occupations Results: The exposure hazards of 30 construction occupations were identified and summarized through a literature review and expert survey. The most prevalent hazards were in order of noise, awkward posture, heat/cold, crystalline silica, cement/concrete dust, metal fumes, and volatile organic compounds. The hazards with highest risk score(over seven points) at construction occupations were noise(formwork carpenter, concrete finisher, rebar worker, demolition worker, driller/rock blaster), hazardous rays(welder), heat/cold (earthworks, formwork carpenter, rebar worker, concrete placer, scaffolder), awkward posture(bricklayer, caulker/tile setter, rebar worker) and heavy lifting(bricklayer, rebar worker). Among construction workers, the job types with the highest risk of exposure to carcinogens, and in which occupational cancer has been reported, were in order of stonemason, concrete finisher, rock blaster, welder, insulation installer, painter, scaffolder, plant worker and earthworks in order Conclusions: Systematic research and discussion on occupational disease among construction workers and its various hazardous factors are needed to establish job exposure matrix for facilitating standard for promptly processing the workers' compensation.

• Journal of the Korean Society of Safety
• /
• v.20 no.1 s.69
• /
• pp.133-136
• /
• 2005

The accidents attributed to the forklift have increased as the number of the forklift increases. It is significant that most of the accidents were fatal. This study investigated slip distance of forklift depending upon the floor materials and their conditions in industrial site. For doing this, an experiment was conducted, in which the floor materials and their conditions were adopted as independent variables and the slip distance as dependent variable. Six floor materials included asphalt concrete, two color hardener mortar, epoxy paint and deluxe tile. Two types of floor conditions, wet and dry, were used in the experiment. The results showed that the slip distance was shorter on the asphalt and concrete floors than on other floors, and that the distance on the wet floor was six times longer than that on the dry condition. Based on this result, it is recommended that as in the advanced countries, the regulation or standard on the floor conditions such as friction coefficient be established for reducing forklift relevant accidents.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2010.05a
• /
• pp.45-49
• /
• 2010

The contamination(stain phenomenon) of natural marble(sipeol, bianko) of art wall of on-site interior finishing system and wall of elevator hall has occurred. The bottom of the art wall of stone junction tile has defects as cracks. To solve these problems, our research team developed eco-friendly complex stone panel(stone 4T + cement board 6T) and high-frequency hot-melt construction method that can construct in winter.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2006.04a
• /
• pp.43-49
• /
• 2006

Construction CALS has contributed much to the improvement of construction management. Recently, the ubiquitous technology brings another opportunities for expanding tile business horizon in construction. The government policies to upgrade the information technologies in Korean offer an environment in which practical application of ubiquitous becomes more practical. To maintain the level of competitiveness, construction companies need to pay attention to the chance of ubiquitous technologies. This paper introduces the research movement in the construction industry in an attempt to find out the feasibility of ubiquitous technologies such as RFID, USN, etc. The construction process, which is executed in the natural environment, will benefit from the state-of-are information technologies in terms of improved communication interface.