• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 지반공학 공동 학술발표회
• /
• pp.621-628
• /
• 2005

The concrete lining in tunnel performs structural and nonstructural functions. The concrete lining works as a structural member for released load and residual water pressure in NATM tunnel system. Also concrete lining used for finishing the tunnel surface. The initial crack of concrete lining is reported because of difficulties in construction process, which concrete is injected into 30$\sim$40cm narrow gap between lining form and tunnel surface through 500${\times}$600mm small injection holes in the form. In this paper, we research a reason of initial crack occurrence by the case study of 4 lane wide span tunnel, and propose an improved method for crack minimization in construction process. We verify that the proposed method can give qualified concrete lining by carrying out the concrete injection model test and the numerical analysis of concrete flow.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표대회 논문집(III)
• /
• pp.900-905
• /
• 1998

This study is about quality test of parmament form for practical application. Nowdays domestic building market in the face of 3D, in addition to construction cost increase, materials lack problems and opening a building market to foreign countries, is trying to find out the efficient ways of overcoming these problems. So the efficiacy of form work to technical improvement will contribute a practical permanent form in field through quality test of permmament form. In this paper, we examined the total system of form erections and evaluated the structural permament of columns and beams.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 가을 학술논문 발표대회
• /
• pp.12-13
• /
• 2020

Free-form buildings usually have large curved shapes on the outside. In order to construct this curved shape, the exterior of the building must be divided into easy-to-manufacture shapes, and the segmented panel is called the FCP(Free-form Concrete Panel). These FCPs have different shapes and cannot reuse molds. To solve these problems, the researchers developed FCP manufacturing equipment to manufacture a mould of FCP. However, the developed equipment alone cannot completely manufacture FCP's mould. This is because there is no mould to implement side of FCP. Therefore, it is necessary to develop a side form of FCP that can be applied to FCP manufacturing equipment. To this end, this study analyzes the basic requirements that side mould should have before developing side mould.

• Journal of the Korean Wood Science and Technology
• /
• 제28권3호
• /
• pp.14-24
• /
• 2000

본 연구에서는 향후 공급량이 증가될 것으로 예상되는 라디아타소나무와 국산 낙엽송의 두 수종을 이용하여 합판을 제조하고 구조용 합판 및 콘크리트 거푸집용 합판으로서의 사용 가능성을 검토하고자 하였다. 먼저, 기초적인 재질을 평가하기 위하여 합판의 재질시험 및 못성능 등의 시험을 실시하였고, 콘크리트조 주택 혹은 목조주택 등의 구조용 재료로의 사용을 검토하기 위해 집중하중과 균일분포하중에 의한 구조성능 시험 및 콘크리트 거푸집용으로서의 성능시험을 실시하였다. 합판의 기초 재질에 해당되는 비중, 너비 굽음, 길이 굽음 비틀림에 대한 실험 결과, 구조용 재료로서의 기준을 만족하였다. 못 측면 저항력, 못 인발 저항력 그리고 못머리 관통력에 대한 실험 결과, 구조용 재료로서의 벽체나 지붕재에 대한 표준성능을 만족하였다. 이들 두 수종으로 제조한 합판의 경우, 집중하중과 균일 분포하중에 의한 구조성능 평가, 콘크리트 거푸집용으로서의 성능 평가 결과를 볼 때 구조용 덮개재, 바탕바닥 마감재, 콘크리트 거푸집용 재료로의 사용이 가능하다고 판단되었다.

• 한국건축시공학회지
• /
• 제13권6호
• /
• pp.522-529
• /
• 2013

As concrete forms, panel forms made of plywood used to be widely used, but recently a system form made of aluminum has been broadly adopted because of the advantages it offers in terms of constructability and economy. However, an aluminum form reacts with concrete, which is alkali, and creates hydrogen gas. As a result, air pockets occur on the concrete's surface, and its finishability deteriorates. Therefore, this research analyzed the relationship between the distribution of voids and surface roughness and the damage degree and number of uses of the aluminum form. The analysis of the distribution of voids shows that the number of voids of 0.1~1 mm, which are considered to have occurred because of chemical reaction, was 200~500 on the coating plywood, but was 1 500~2 000 on the aluminum form after 3 uses, and impossible to count after a higher number of uses. Surface roughness was $1.7{\sim}3.2{\mu}m$ on the coating plywood form, but was about $2.6{\mu}m$ after the first use and about $6.8{\mu}m$ after 10 uses, a 2.6-fold increase. Distribution of voids did not show a particular tendency depending upon the degree of damage to the concrete form, but surface roughness showed an increasing tendency as the degree of damage grows. Therefore, when using aluminum forms, surface maintenance should be carried out completely, such as prevention of damages to the form surface coating materials and spreading of separating materials on forms.

• 한국건설관리학회논문집
• /
• 제4권4호
• /
• pp.88-95
• /
• 2003

탈수거푸집공법은 거푸집 표면에 잉여수를 배출시킬 수 있는 구멍을 뚫고 내측에 섬유포를 부착하여 콘크리트 타설시 잉여수 및 혼입공기를 배출시키는 공법으로 시공상의 워커빌리티를 확보하면서 콘크리트 표층부 품질을 강화시킬 수 있다. 따라서 제치장 콘크리트 표면의 강도를 극대화할 뿐만 아니라, 수밀한 콘크리트 표층부를 생성하기 때문에 물이나 공기, 염분 등이 침투하기 어려워 콘크리트의 내구성을 크게 향상시킬 수 있다. 그러나 현재 국내에서는 이론적으로는 제기되고 있으나, 관련규준 및 시공방법에 대한 연구가 부재해 공사현장에서 적용할 기회가 없는 실정이다. 이에 본 연구에서는 물성실험을 통해 탈수거푸집 설계를 위한 기초자료를 제공하고, 이를 바탕으로 한 현장적용실험을 통해 탈수거푸집공법의 실용화 방안을 제안하고자 한다.

• 한국건축시공학회지
• /
• 제9권1호
• /
• pp.49-55
• /
• 2009

In this study, reduction methods of surface air void were examined for high performance concrete having high viscosity. The effects of assumed influencing factors such as form types, form-coating materials, tamping equipments and methods were examined based on the tests on mock-up specimens made of high performance concrete. The test results can be summarized as follows: As for form types, the most favorable results were obtained when coated plywood form was used with panel-shape tamping equipments at the contact region with concrete, the second and the third being the water/air-permeable sheets and steel with coated plywood, respectively. As for tamping equipments, a vibrator with 6.5cm diameter was most effective. Finally, the shorter the tamping intervals, the better the reduction effect of surface air void. As a conclusion, an improved method was proposed to reduce surface air void and it was verified with the test result that only four air voids as large as $5{\sim}10mm$ are found in the are of $1m^2$.

• Computers and Concrete
• /
• 제16권2호
• /
• pp.287-309
• /
• 2015

FormWorks-Plus is a generalized public domain user-friendly preprocessor developed to facilitate the process of creating finite element models for structural analysis programs. The lack of a graphical user interface in most academic analysis programs forces users to input the structural model information into the standard text files, which is a time-consuming and error-prone process. FormWorks-Plus enables engineers to conveniently set up the finite element model in a graphical environment, eliminating the problems associated with conventional input text files and improving the user's perception of the application. In this paper, a brief overview of the FormWorks-Plus structure is presented, followed by a detailed explanation of the main features of the program. In addition, demonstration is made of the application of FormWorks-Plus in combination with VecTor programs, advanced nonlinear analysis tools for reinforced concrete structures. Finally, aspects relating to the modelling and analysis of three case studies are discussed: a reinforced concrete beam-column joint, a steel-concrete composite shear wall, and a SFRC shear panel. The unique mixed-type frame-membrane modelling procedure implemented in FormWorks-Plus can address the limitations associated with most frame type analyses.

• Steel and Composite Structures
• /
• 제22권2호
• /
• pp.387-398
• /
• 2016

In order to evaluate the effects of U shape ultra high performance concrete (UHPC) permanent form on the behaviors of Reinforced Concrete (RC) beam, a full scale RC composite beam is designed and tested with U shape UHPC permanent form and a reference RC beam with same parameters is tested simultaneously for comparison. The effects of the permanent form on the failure mode, cracking strength, ultimate capacity and deformation are studied. Test results shows that the contributions of the U shape UHPC permanent form to the flexural cracking behaviors of RC beam are significant. This study may provide a reference for the design of sustainable RC beam with high durable UHPC permanent form.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 가을 학술발표회 논문집
• /
• pp.749-754
• /
• 1997

Nowadays domestic building market has undergone several changes. Labor costs are too high and materials are in short supply. These raised building costs and therefore lowered productivity. At this point it is the best way to reduce manual labor and find alternative materials that can improve productivity. In the building process form work take the most part of it. So many formwork systems were developed to reduce the construction period and labor cost. But their technical improvements just limited to adjust form shape-the role of form is not changed. This research developed a new formwork systems that can function to unify or minimze the unit process with cast-in-place type permanent form. In former study (reported in '97 spring seminar), we did the assembling test with column and beam clamps. Furthermore, In this paper, we examined the total systems of form erections and evaluated the structural performances.