• Computational Structural Engineering
• /
• v.32 no.4
• /
• pp.4-10
• /
• 2019

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.10a
• /
• pp.21-28
• /
• 2003

The use of frequency-dependent spectral element matrix (or dynamic stiffness matrix) in structural dynamics may Provide very accurate solutions, while it reduces the number of degrees of freedom to improve the computational efficiency and cost problems. Thus, this paper develops a spectral element model for the coupled thermoelastic beam-plate moving with constant speed under uniform in-plane tension.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.614-622
• /
• 2011

In this study, the computational structural dynamic modeling of floating offshore wind turbine system is presented using efficient equivalent modeling technique. Structural dynamic behaviors of the offshore floating platform with 5MW wind turbine system have been analyzed using computational multi-body dynamics based on the finite element method. The considered platform configuration of the present offshore wind turbine model is the typical spar-buoy type. Equivalent stiffness and damping properties of the floating platform were extracted from the results of the baseline model. Dynamic responses for the floating wind turbine models are presented and compared to investigate its structural dynamic characteristics. It is important shown that the results of the present equivalent modeling technique show good and reasonable agreements with those by the fully coupled analysis considering complex floating body dynamics.

• Computational Structural Engineering
• /
• v.3 no.4
• /
• pp.24-28
• /
• 1990

I-DEAS System Dynamics Analysis는 컴퓨터에 의한 해석적 동특성 파악이 어려운 구조요소와 해석적 동특성 파악이 가능한 구조요소가 함께 결합되어 있는 복잡한 구조물에 대하여, 전자의 구조요소에 대해서는 실험에 의해 추출된 동특성을 후자의 구조요소에 대해서는 컴퓨터 해석에 의한 동특성을 사용하여 전체 구조 시스템에 대한 동적해석을 가능하게 하는 프로그램이다.

• Computational Structural Engineering
• /
• v.26 no.2
• /
• pp.55-60
• /
• 2013

• Computational Structural Engineering
• /
• v.18 no.2 s.68
• /
• pp.25-33
• /
• 2005

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.2
• /
• pp.52-58
• /
• 2011

In this study, the design and verification of 6 kW class lift-type vertical-axis wind turbine (VAWT) has been conducted using advanced CAE technique based on computational fluid dynamics (CFD), finite element method (FEM), and computational structural dynamics (CSD). Designed aerodynamic performance of the VAWT model is tested using unsteady CFD method. Designed structural safety is also tested through the evaluation of maximum induced stress level and resonance characteristics using FEM and CSD methods. It is importantly shown that the effect of master eccentricity due to rotational inertia needs to be carefully considered to additionally investigate dynamic stress and deformation level of the designed VAWT system.

• The KSFM Journal of Fluid Machinery
• /
• v.15 no.6
• /
• pp.11-17
• /
• 2012

The one way fluid structure interaction analysis on advanced propeller blade for next generation turboprop aircraft. HS1 airfoil series are selected as a advanced propeller blade airfoil. Adkins method is used for aerodynamic design and performance analysis with respect to the design point. Adkins method is based on the vortex-blade element theory which design the propeller to satisfy the condition for minimum energy loss. propeller geometry is generated by varying chord length and pitch angle at design point. Blade sweep is designed based on the design mach number and target propulsion efficiency. The aerodynamic characteristics of the designed Advanced propeller were verified by CFD(Computational Fluid Dynamic) and showed the enhanced performance than the conventional propeller. The skin-foam sandwich structural type is adopted for blade. The high stiffness, strength carbon/epoxy composite material is used for the skin and PMI(Polymethacrylimide) is used for the foam. Aerodynamic load is calculated by computational fluid dynamics. Linear static stress analysis is performed by finite element analysis code MSC.NASTRAN in order to investigate the structural safety. The result of structural analysis showed that the design has sufficient structural safety. It was concluded that structural safety assessment should incorporate the off-design points.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.04a
• /
• pp.663-670
• /
• 2011

In this study, the design and verification of 6kW class lift-type vertical-axis wind turbine (VAWT) has been conducted using advanced CAE technique based on computational fluid dynamics (CFD), finite element method (FEM), and computational structural dynamics (CSD). Designed aerodynamic performance of the VAWT model is tested using unsteady CFD method. Designed structural safety is also tested through the evaluation of maximum induced stress level and resonance characteristics using FEM and CSD methods. It is importantly shown that the effect of master eccentricity due to rotational inertia needs to be carefully considered to additionally investigate dynamic stress and deformation level of the designed VAWT system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.64-71
• /
• 2011

In this study, steady and unsteady aerodynamic analyses of a huge rocket configuration have been conducted in a transonic flow region. The launch vehicle structural response are coupled with the transonic flow state transitions at the nose of the payload fairing. The developed fluid-structure coupled analysis system is applied for aeroelastic computations combining computational structural dynamics(CSD), finite element method(FEM) and computational fluid dynamics(CFD) in the time domain. It can give very accurate and useful engineering data on the structural dynamic design of advanced flight vehicles. For the nonlinear unsteady aerodynamics in high transonic flow region, Navier-Stokes equations using the structured grid system have been applied to the rocket configurations. Also, it is typically shown that the current computation approach can yield realistic and practical results for rocket design and test engineers.