• 한국구조물진단유지관리공학회 논문집
• /
• 제20권4호
• /
• pp.9-18
• /
• 2016

이 연구에서는 태양열 에너지 저장용도로 사용하기 위한 시멘트 기반 복합재료의 열적 및 역학적 특성을 파악하였다. 다양한 시멘트 재료의 배합이 섬유보강 시멘트 기반 복합재료의 열적 및 역학적 특성에 미치는 영향을 파악하기 위한 실험연구를 수행하였다. 시멘트 기반 복합재료의 역학적 특성으로써 열싸이클 전과 후의 압축강도 및 인장강도를 측정하였다. 또한, 섬유보강 시멘트 기반 복합재료의 열적 특성으로써 열전도율과 비열을 측정하였다. OPC와 슬래그를 포함한 배합의 잔류압축강도가 가장 크게 나타난다. 그라파이트를 혼합한 배합의 열전도율이 크게 나타나며, 이는 그라파이트가 열저장 시스템의 효율적인 축열과 방열에 유리함을 의미한다. 또한, CSA 또는 지르코늄의 첨가는 섬유보강 복합재료의 비열을 증가시킨다. 실험연구결과는 잡광형 태양열 발전소에서 고성능 복합재료를 사용하는 열저장 시스템 설계에 기초자료로 활용될 수 있다.

• Steel and Composite Structures
• /
• 제42권3호
• /
• pp.407-426
• /
• 2022

Superior to traditional welded studs, high strength friction-grip bolted shear connectors facilitate the assembling and demounting of the composite members, which maximizes the potential for efficiency in the construction and retrofitting of new and old structures respectively. Hence, it is necessary to investigate the structural properties of high strength friction-grip bolts used in steel concrete composite beams. By means of push-out tests, an experimental study was conducted on post-installed high strength friction-grip bolts, considering the effects of different bolt size, concrete strength, bolt tensile strength and bolt pretension. The test results showed that bolt shear fracture was the dominant failure mode of all specimens. Based on the load-slip curves, uplifting curves and bolt tensile force curves between the precast concrete slab and steel beam obtained by push-out tests, the anti-slip performance of steel-concrete interface and shear behavior of bolt shank were studied, including the quantitative analysis of anti-slip load, and anti-slip stiffness, frictional coefficient, shear stiffness of bolt shank and ultimate shear capacity. Meanwhile, the interfacial anti-slip stiffness and shear stiffness of bolt shank were defined reasonably. In addition, a total of 56 push-out finite element models verified by the experimental results were also developed, and used to conduct parametric analyses for investigating the shear behavior of high-strength bolted shear connectors in steel-concrete composite beams. Finally, on ground of the test results and finite element simulation analysis, a new design formula for predicting shear capacity was proposed by nonlinear fitting, considering the bolt diameter, concrete strength and bolt tensile strength. Comparison of the calculated value from proposed formula and test results given in the relevant references indicated that the proposed formulas can give a reasonable prediction.

• Electronic Materials Letters
• /
• 제14권6호
• /
• pp.718-724
• /
• 2018

With the development of photovoltaic industry, the cost of photovoltaic power generation has become the significant issue. And the metallization process has decided the cost of original materials and photovoltaic efficiency of the solar cells. Nowadays, double printing process has been introduced instead of one-step printing process for front contact of polycrystalline silicon solar cells, which can effectively improve the photovoltaic conversion efficiency of silicon solar cells. Here, the relative cheap Cu paste has replaced the expensive Ag paste to form Ag/Cu composite front contact of silicon solar cells. The photovoltaic performance and the cost of photovoltaic power generation have been investigated. With the optimization on structure and height of Cu finger layer for Ag/Cu composite double-printed front contact, the silicon solar cells have exhibited a photovoltaic conversion efficiency of 18.41%, which has reduced 3.42 cent per Watt for the cost of photovoltaic power generation.

• Journal of electromagnetic engineering and science
• /
• 제14권1호
• /
• pp.15-24
• /
• 2014

A compact dual-band three-way metamaterial power divider is proposed that has three in-phase outputs. Fully printed composite rightand left-handed (CRLH) unequal and equal power dividers are first implemented for 900-MHz and 2.4-GHz bands with the power-division ratios of 2:1 and 1:1, respectively. An initial 1:1:1 power divider is then achieved by incorporating the input of the two-way equal block into an output of the unequal block, and trimming the interconnection parameters. The condition of an identical phase at the three outputs of the power divider is then met by devising a hybrid CRLH phase-shift line to compensate for the different phase errors at the two frequencies. This scheme is confirmed by predicting the performance of the power divider with circuit analysis and full-wave simulation and measuring the fabricated prototype. They results show agreement; the in-phase outputs as well as the desirable power-division are accomplished and outdo the conventional techniques.

• 전산구조공학
• /
• 제27권3호
• /
• pp.40-48
• /
• 2014

• 전기학회논문지
• /
• 제66권10호
• /
• pp.1499-1507
• /
• 2017

This paper presents an impact-based piezoelectric vibration energy harvester using a freely movable metal sphere and a piezoceramic fiber-based MFC (Macro Fiber Composite) as piezoelectric cantilever. The free motion of the metal sphere, which impacts both ends of the cavity in an aluminum housing, generates power across a cantilever-type MFC beam in response to low frequency vibration such as human-body-induced motion. Impacting force of the spherical proof mass is transformed into the vibration of the piezoelectric cantilever indirectly via the aluminum housing. A proof-of-concept energy harvesting device has been fabricated and tested. Effect of the indirect impact-based system has been tested and compared with the direct impact-based counterpart. Maximum peak-to-peak open circuit voltage of 39.8V and average power of $598.9{\mu}W$ have been obtained at 3g acceleration at 18Hz. Long-term reliability of the fabricated device has been verified by cyclic testing. For the improvement of output performance and reliability, various devices have been tested and compared. Using device fabricated with anodized aluminum housing, maximum peak-to-peak open-circuit voltage of 34.4V and average power of $372.8{\mu}W$ have been obtained at 3g excitation at 20Hz. In terms of reliability, housing with 0.5mm-thick steel plate and anodized aluminum gave improved results with reduced power reduction during initial phase of the cyclic testing.

• Elastomers and Composites
• /
• 제47권4호
• /
• pp.310-317
• /
• 2012

계면접착력 향상을 위해 실린더형 RF 플라즈마 발생기를 이용하여 Jute fiber의 표면을 아르곤가스로 처리하였고 최적 처리조건을 설정하였다. 플라즈마 강도, 가스압력, 및 처리시간을 변경한 후 이러한 인자들이 황마섬유 표면모폴로지, 섬유 인장강도, 및 폴리프로필렌과의 모델복합체에서 계면접착강도에 미치는 영향을 조사하였다. 플라즈마 처리인자에 따라 황마섬유의 표면은 거칠어졌다. 가스압력의 영향은 처리시간 및 플라즈마 강도의 영향보다 다소 낮게 나타났다. 플라즈마 강도와 시간에 따라 황마섬유의 강도는 약 25% 감소한 반면, 가스압력의 영향은 크게 나타나지 않았다. 계면전단강도 (IFSS)를 기준으로 결정된 최적 플라즈마 처리조건은 처리시간 30 s, 전력 40 W, 가스압력 30 mTorr로 나타났다.

• 정보학연구
• /
• 제6권2호
• /
• pp.1-8
• /
• 2003

본 연구는 최근 새로운 통신 방식으로 제안되고 있는 저압 전력선 통신에 대해서 검토한다. 저압 전력선 통신을 위한 지연, 감쇠, 주파수 선택적 페이딩의 특성을 갖는 전력선채널의 모델링과 함께 이 채널 특성에 다중 반송파 변조의 일종인 OFDM(Orthogonal Frequency Division Multiplexing)방식을 적용해 봄으로써 전력선 통신에 OFDM변조 방식이 적합한지 분석한다

• 한국응용과학기술학회지
• /
• 제41권1호
• /
• pp.46-57
• /
• 2024

In this study, the various process conditions for high-power DC Magnetron Sputtering (DCMS) on the surface roughness of carbon thin films were investigated. The optimal conditions for Si/C coating were 40min for deposition time, which does not deviate from normal plasma, to obtain the maximum deposition rate, and the conditions for the best surface roughness were -16volt bias voltage and 400watt DC power with 1.3x10-3torr chamber pressure. Under these optimal conditions, an excellent carbon thin film with a surface roughness of 1.62nm and a thickness of 724nm was obtained. As a result of XPS analysis, it was confirmed that the GLC structure (sp² bonding) was more dominant than the DLC structure (sp³ bonding) in the thin film structure of the carbon composite layer formed by DC sputtering. Except in infrequent cases of relatively plasma instability, the lower bias voltage and applied power induces smaller surface roughness value due to the cooling effect and particle densification. For the optimal conditions for Graphite/C composite layer coating, a roughness of 36.3 nm and a thickness of 711 nm was obtained under the same conditions of the optimal process conditions for Si/C coating. This layer showed a immensely low roughness value compared to the roughness of bare graphite of 242 nm which verifies that carbon coating using DC sputtering is highly effective in modifying the surface of graphite molds for glass forming.

• 공업화학
• /
• 제29권6호
• /
• pp.663-669
• /
• 2018

초음파 추출공정을 이용하여 밀싹으로부터 유효성분을 추출하고, 중심합성계획모델을 이용하여 추출공정을 최적화하였다. 중심합성계획모델의 반응치로는 추출수율과 플라보노이드성분 함량을 설정하고, 독립변수인 추출시간, 주정/초순수 부피비, 초음파 조사세기에 따른 주효과도와 교호효과도를 해석하였다. 추출수율의 경우 주정/초순수의 부피비와 초음파 조사세기가 상대적으로 큰 영향을 미쳤으며, 플라보노이드성분 함량의 경우에는 추출시간의 영향이 가장 크게 나타났다. 추출수율과 플라보노이드성분 함량을 모두 고려한 결과 최적조건은 추출시간(17.00 min), 주정/초순수의 부피비(50.25 vol%), 초음파 조사세기(551.70 W)이며, 이때 예측 추출수율은 28.43 wt%, 예측 플라보노이드성분 함량은 $29.99{\mu}g\;QE/mL\;dw$을 얻을 수 있었다. 실험을 통해 유효성분 추출수율(28.73 wt%), 플라보노이드성분 함량 ($29.65{\mu}g\;QE/mL\;dw$)의 실험값을 얻을 수 있었으며, 이를 예측값과 비교했을 때 오차율은 각각 1.05, 1.13%이다.