• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.245-254
• /
• 2009

Efficiency of landfill liners system is usually evaluated based on leakage rate and mass flux. In this study, composite liner systems including the GCL(geosynthetic clay liner) composite liner, the Subtitle D liner, the Wisconsin NR500 liner, and the recently utilized double composite liner, which is a combination of the GCL composite liner and Subtitle D-type liner, have been examined. The leakage rate through circular and long defects in the geomembrane (GM) of the liner system was analyzed with the aids of analytical and numerical methods. For the mass flux criterion, contaminant transport through defects in the GM of landfill liners can be evaluated based on the calculated leakage rates. The diffusion rate of volatile organic compounds through intact landfill liners was evaluated by performing a one-dimensional numerical model. Cadmium and toluene were adoptted in the analyses as typical inorganic and organic substances, respectively, which will be chemical species encountered during landfill operation. The performance-based evaluation indicates that the double composite liner systems are superior to the other types of liner.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.295-304
• /
• 2010

Performance of a landfill liner is evaluated based on leakage rate and mass flux. In this study, the recently utilized double composite liner system, which consists of a geomembrane (GM), a geosynthetic clay liner (GCL), a GM, and a compacted clay layer (61 or 91.5 cm) is compared with other popular composite liners including the single GCL system, the Subtitle D liner system, and the Wisconsin NR500 liner system. The leakage rate through circular and long defects in the GM of the landfill liners is analyzed using numerical models. For the mass flux criterion, the analyses of inorganic contaminant transport through defects in the GM component of liner systems and diffusion of organic compounds through intact landfill liners are conducted using three- and one-dimensional numerical models, respectively. Cadmium and toluene are used in the analyses as a typical inorganic and organic substance, respectively, which will be chemical species encountered during landfill operation. The comparison shows that the double composite liner systems are superior to the other liner systems according to the performance-based evaluation.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.45-48
• /
• 2005

In manufacturing process of composite cylinders with metal liner, the autofrettage process which induces compressive residual stress on liner to improve cycling life can be applied. In this study, finite element analysis technique is presented, which can predict accurately the compressive residual stress on liner induced by autofrettage and stress behavior after. Material and geometry non-linearity is considered in finite element analysis, and the Von-Mises stress of a liner is introduced as a key parameter that determines pressure cycling life of composite cylinders. Presented methodology is verified through fatigue test of liner material and pressure cycling test of composite cylinders.

• Journal of Mechanical Science and Technology
• /
• v.17 no.2
• /
• pp.171-180
• /
• 2003

One of the most significant problems in the processing of composite materials is residual stress. The high residual stress may cause cracking in the matrix without external loads and degrade the integrity of composite structures. In this study, thermo-viscoelastic residual stresses occurred in an aluminum liner-inserted polymer composite cylinder are investigated. This type of the structure is used for rocket fuselage due to the convenience to attach payloads and equipment to the metal liner by machining. The time and degree of cure dependent thermo-viscoelastic constitutive equations are developed and coupled with a thermo-chemical process model. These equations are solved with the finite element method to predict the residual stresses in the composite cylinder and also in the interface between the liner and the composite during cure.

• Journal of Welding and Joining
• /
• v.32 no.5
• /
• pp.72-79
• /
• 2014

Shaped charge(SC) ammunition is a weapon that penetrates directly the target by made jet from metal liner on impacting at a target. In SC, the liner occupies significantly important role causing an explosion and penetration of the target. The Al-Ni composite coating was deposited on copper liner in a solid state via kinetic spraying to improve the explosive force. The mechanical properties, reactivity and microstructure were investigated to confirm the possibility of kinetic sprayed Al/Ni composite coating as a reactive liner material. Reactive liner using Al/Ni composite exhibited much enhanced reactivity than pure copper liner due to Self-propagating High-temperature Synthesis (SHS) reaction with significantly improved adhesive bond strength. Especially, among the Al/Ni composite coatings, AN11 (the Al versus Ni atomic percent ratio is 1:1) showed the greatest reactivity due to its widest reaction area between deposited Al and Ni.

• Aerospace Engineering and Technology
• /
• v.2 no.2
• /
• pp.124-132
• /
• 2003

This paper described the structural design and the fabrication procedure of KSR-III composite pressure tank. The type of the composite pressure tank was COPV(Composite Overwrapped Pressure Vessel). A non-load sharing liner was made of aluminum 6061-0 and the liner provided a helium gas seal. The composite pressure tank was winded using T700 carbon/epoxy on the liner. Because the aluminum liner was thin, multiple cure cycles were applied to the filament winding technique. The multiple cure cycles prevented the liner-cylinder from losing a circular shape. A fitting force at the metallic boss was spread to the carbon fiber by a boss ring. The boss ring also prevented a local deformation at the boss part.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.9
• /
• pp.1012-1019
• /
• 2012

In this study, CNG composite vessel is analyzed by using coupled model with liner and composite layer. For the coupled model, a method using theoretical analysis and FEA is suggested: elastic solution for laminated tube is used for theoretical analysis of the composite vessel, FEA is performed to the model of CNG composite vessel in actual conditions. On the basis of these results, optimal thickness and winding angle of the composite layer considering the material properties and thickness of the liner are determined. The results of theoretical analysis and FEA are compared with those carried out in previous studies for verifying the suggested analysis method.

• Composites Research
• /
• v.19 no.1
• /
• pp.22-28
• /
• 2006

In manufacturing process of composite cylinders with metal liner, the autofrettage process which induces compressive residual stress on the liner to improve cycling life can be applied. In this study, a finite element analysis technique is presented, which can predict accurately the compressive residual stress on the liner induced by autofrettage and stress behavior after. Material and geometrical non-linearity is considered in the finite element analysis, and the Von-Mises stress of a liner is introduced as a key parameter that determines pressure cycling life of composite cylinders. Presented methodology is verified through fatigue test of liner material and pressure cycling test of composite cylinders.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.5
• /
• pp.78-83
• /
• 2015

In the composite case, the first ply failure is considered total failure of the case. When the case is constructed by filament winding over a metal liner, the first ply failure does not necessarily mean total failure of the case. In this study, we compared the results through finite element analysis and burst test to predict the burst pressure of the hybrid case (filament-wound composite case with metal liner). Through it predicts the burst pressure of the hybrid case, we can determine the thickness of the metal liner and composite.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 1999.10a
• /
• pp.73-76
• /
• 1999

Soil-bentonite mixtures are frequently used as impervious for waste disposal sites. In the present work, bentonite composite liner systems(BCL) have been developed by utilizing Korean zeolitic bentonites. The geomechanical properties of the liner systems, such as strength, hydraulic conductivity, etc. have been studied. The laboratory and field test results are also be presented.