• Journal of the Korean Society for Advanced Composite Structures
• /
• v.4 no.1
• /
• pp.15-24
• /
• 2013

This project investigated the use of two types of thermoplastic pipes, High-Density Polyethylene (HDPE) and Poly-vinyl Chloride (PVC), as cross-drains under highways. Pipes ranging from 0.3 m (12 in.) to 1.5 m (60 in.) in diameter were evaluated under deep fills, minimum cover, and construction loads. In addition to a comprehensive literature review, an analytical study into the allowable fill heights for thermoplastic pipes and a field study to observe the installation and performance of the pipe in service conditions were conducted. Based on the study findings, recommendations regarding how and when thermoplastic pipe should be installed are provided.

• Journal of Welding and Joining
• /
• v.17 no.5
• /
• pp.107-115
• /
• 1999

The objective of this research was to study the formation of the thick hardened layer with the addition of metal powder(Cu) and ceramics powders(TiC) on the aluminum 5083 alloys by plasma transferred arc process(PTA process) and to characterize the effect of overlaying conditions on the overlaid layer formation. This was followed by investigating the microstructures of the overlaid layers and mechanical properties such as hardness and wear resistance. The overlaid layer containing copper powder was alloyed and intermetallic compound($CuAl_2$) was formed. The overlaid layers with high melting point TiC powders, however, did not react with base metal. Wear resistance of the alloyed layer was remarkably improved by the formation of $CuAl_2$, precipitate phase, which prevented wear of base aluminum alloys and at higher wear speed, accelerated sliding of the counter part. Wear resistance of the composite layer was also remarkably improved because TiC powder act as a load barring element and Fe debris fragments detached from the counter part act as a solid lubricant on the contact surface.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.6
• /
• pp.920-925
• /
• 2012

A study of vehicle weight lightening has been progressed to reduce the fuel consumption. In this paper, the body floor in an EV (Electric Vehicle) bus has been applied by composites as CFRP and GFRP. In order to analyse a various reliability and safety, an experiment and FEM analysis was carried out to obtain weight lightening. Especially, the joint. An effective design is obtained through an experiment as well as FEM analysis. Results of stress analysis of GFRP material showed twice as much displacement than those of CFRP material. Among three kinds of joint methods, the bond joint method is occurred to a substantial shape change in the body and floor. It is found that the rivet joints are fairly suitable for stress sustaining capability.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2007.04a
• /
• pp.565-570
• /
• 2007

Fiber reinforced polymer(FRP) composite decks are new to bridge applications and hence not much literature exists on their structural mechanical behavior. As there are many differences between numerical displacements through static analysis of the primary model and experimental displacements through static load tests, system identification (SI)techniques such as Neural Networks (NN) and support vector machines (SVM) utilized in the optimization of the FE model. During the process of identification, displacements were used as input while stiffness as outputs. Through the comparison of numerical displacements after SI and experimental displacements, it can note that NN and SVM would be effective SI methods in modeling an FRP deck. Moreover, two methods such as response surface method and iteration were proposed to optimize the estimated stiffness. Finally, the results were compared through the mean square error (MSE) of the differences between numerical displacements and experimental displacements at 6 points.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.3
• /
• pp.248-254
• /
• 2015

The strength and fatigue life of Satin and Twill-woven CF/epoxy composite(CFRP) have been investigated. Damage mechanism fatigue method has been used to assess fatigue damage accumulation. It is based on measured residual stiffness and residual strength of carbon-fiber reinforced plastic(CFRP) laminates under cyclic loading. Fatigue damage evolution in composite laminates and predict fatigue life of the laminates were simulated by finite element analysis(FEA) method. The stress analysis was carried out in MSC patran/Nastran. A modified Hashin's failure criterion di rmfjapplied to predict the failure of the experimental data of fatigue life but a Ye-delamination criterion was ignored because of 2D modeling. Almost linear stiffness and strength degradation were observed during most of the fatigue process. These stress distribution data were adopted in the simulation to simulate fatigue behavior and estimate life of the laminates. From the results, the predicted fatigue life is more conservatively estimated than the experimental results.

• Composites Research
• /
• v.17 no.2
• /
• pp.34-39
• /
• 2004

In this paper, a modified and representative unit cell model was employed to study the tensile behaviour of closed-cell metallic foams with varying spatial density distribution as well as material imperfections. The density variation was assumed to follow a statistical probability distribution of the Gaussian type. A multiple cell finite element model, utilising the modified unit cell, was developed. The model exhibits deformation patterns similar to those observed in tensile testing. The nominal stress-strain curve obtained from quasistatic tensile of the foam was compared with experimental findings and was found to be in good agreement in the scheme of maximum strength only if the appropriate density distribution and volume fraction of internal imperfections are taken into account. Moreover, maximum tensile strength of the aluminium foam was found to be more sensitive to the volume fraction of imperfection than standard deviation of the density.

• Journal of electromagnetic engineering and science
• /
• v.14 no.4
• /
• pp.360-366
• /
• 2014

A single-feed composite cavity-backed four-arm curl antenna is presented for use in global positioning systems (GPS). Its primary radiating element is fed by a vacant-quarter printed ring, which helps the antenna directly match to a $50-{\Omega}$ coaxial line and produce a good circular polarization (CP). The cavity-backed reflector is employed to improve the CP radiation characteristics in terms of 3-dB axial ratio (AR) beamwidth and minimum AR value. The optimized design with an overall size of $90{\times}90{\times}25mm^3$ ($0.4725{\lambda}_o{\times}0.4725{\lambda}_o{\times}0.13{\lambda}_o$ at 1,575 MHz) results in a ${\mid}S_{11}{\mid}<-10dB$ bandwidth of 8.66% (1,514-1,651 MHz) and a 3-dB AR bandwidth of 2.23% (1,555-1,590 MHz). The antenna radiates a widebeam right-hand circular polarization and operates with a measured radiation efficiency greater than 90% within its impedance matching bandwidth.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.2
• /
• pp.27-32
• /
• 2013

A valve is a marine structure that is subjected to multiple seawater loads. Therefore, it is necessary to define the kind of loads applied to it to confirm whether the structure has sufficient strength. In this research, we aimed to find the optimal solution for the stress and deformation of valves under various loads. We first selected design variables and implement a finite element analysis according to changes in the thickness of each component of a valve based on a central composite design. Next we developed a regression model of the response surface. Using this model, we calculated the optimal objective value based on NSGA-II. Finally, to confirm the correspondence between the optimal objective value and the real FEM value, we compared the optimal result and structural analysis result to verify the performance of NSGA-II.

• Journal of the Korean Society of Safety
• /
• v.7 no.1
• /
• pp.39-45
• /
• 1992

The impulsive stress and wave propagation of a glass/epoxy laminate subjected to the transverse low-velocity impact of a steel ball are investigated theoretically and experimentally. A plate finite element model based on Whitney and Pagano's theory In consunchon with experimental contact laws is used for the theoretical investigation. The specimens fo, statical indentation and impact test we composed of ［0/45/0/-45/0］$_{2s}$ and ［90/45/90/-45/90］$_{2s}$ stacking sequences and have clamped-simply supported boundary conditions. Finally, these two results are compared and then the impulsive stress and wave propagation characteristics of this laminated composite are studied.ied.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.11
• /
• pp.790-800
• /
• 2013

The optimal structure of 1-3 piezocomposites has been determined by controlling polymer properties, ceramic volume fraction, thickness of composite and aspect ratio of the composite to maximize the TVR (transmitting voltage response), RVS (receiving voltage sensitivity) and FBW (fractional bandwidth) of underwater acoustic transducers. Influence of the design variables on the transducer performance was analyzed with equivalent circuits and the finite element method. When the piezocomposite is vibrating in a pure thickness mode, inter-pillar resonant modes are likely to occur between lattice-structured piezoceramic pillars and polymer matrix, which significantly deteriorate the performance of the piezocomposite. In this work, a new method to design the structure of the 1~3 type piezocomposite was proposed to maximize the TVR, RVS and FBW while preventing the occurrence of the inter-pillar modes. Genetic algorithm was used in the optimal design.