• Computers and Concrete
• /
• v.14 no.5
• /
• pp.613-633
• /
• 2014

A double-skinned composite tubular (DSCT) column, which consists of concrete and inner and outer tubes, was finally developed to overcome the weaknesses of concrete filled tube columns by reducing the self-weight of the column and confining the concrete triaxially. Research pertaining to the stiffness and strength of the column and the confining effect in a DSCT column has been carried out. However, detailed studies on the confining stress, especially the internal confining stress in a DSCT column, have not been carried out. Internal and external confining stresses should be evaluated to determine the effective confining stress in a DSCT column. In this paper, the confining stresses of concrete before and after insertion of an inner tube were studied using finite element analysis. The relationship between the internal or external confining stresses and the theoretical confining stress was investigated by parametric studies. New modified formulae for the yield and buckling failure conditions based on the formulae suggested by former researchers were proposed. Through analytical studies, the modified formulae were verified to be effective for economic and reasonable design of the inner tubes in a DSCT column under the same confining stress.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.439-442
• /
• 2009

In this study, the residual strength of CFRP filament winding pressure vessel after low velocity impact was evaluated quantitatively. After impact test, the pressure vessel was sectioned to produce 25 mm-wide ring specimen and the bursting pressure of this specimen was measured. A finite element model was also fabricated to investigate the deformation and stress distribution characteristics of the impacted CFRP vessel. The degradation of the residual strength along with the increase of impact energy was successfully measured and reviewed.

• Fibers and Polymers
• /
• v.7 no.1
• /
• pp.42-50
• /
• 2006

In this paper, elasto-plastic constitutive equations for highly anisotropic and asymmetric materials are developed and their numerical implementation is presented. Some engineering materials such as fiber reinforced composites show different material behavior in the different material directions (anisotropy) as well as in tension and compression (asymmetry). Although these materials have mostly been analyzed using the anisotropic elastic constitutive equations, the necessity of consideration of plastic properties has been frequently reported in the previous works. In order to include both the anisotropic and asymmetric properties of composite materials, the Drucker-Prager yield criterion is modified by adding anisotropic parameters and initial components of translation. The implementation procedure for the developed theory and algorithms is presented based on the implicit finite element scheme. The measured data from the previous work are used to validate the present constitutive equations.

• Aerospace Engineering and Technology
• /
• v.2 no.1
• /
• pp.213-222
• /
• 2003

Some analytical methods to analyze low-velocity impact force history of composite laminated structures used in aerospace vehicles are reviewed. A classical method used at initial research of low-velocity impact problem in 1980s was reviewed on its physical meaning, and the approximate method assuming the shape of impact force history as a sinusoidal wave was reviewed. A parametric study on contact constant and exponent in contact law was performed in order to analyze an effect on impact force history, and finally its was understood that impact force history could be analyzed accurately even though the linearized contact law was used. Also, in this paper it was shown that impact problem could be analyzed simply and easily using a commercial finite element code.

• 한국전기화학회:학술대회논문집
• /
• 2003.11a
• /
• pp.141-151
• /
• 2003

The electrochemical activity of the olivine type $LiMPO_4$ (M=transition metals) cathodes strongly depends on various factors, e.g., the transition metal element M, perturbative doping of the supervalent cations into Li site, composite formation with conductive additives, state of charge/discharge, and particle size and its geometries, etc. This is, therefore, an important issue of interdisciplinary between electrochemistry and solid state science towards practical applications. In order to shed light on this interesting but complicated issue with the transport properties and crystallographic aspects, systematic discussion will be made with the review of our recent publications; (1) first principle derivation of the electronic structures, (2) crystallographic mapping of the selected solid solutions, (3) quantitative elucidation of the electron-lattice interaction, (4) spectroscopic detection of the local environment with Mossbauer and EXAFS, (5) synthetic optimization of the electrode composite, and (6) electrochemical evaluation of the reaction kinetics, particularly on M = Fe, Mn.

• Composites Research
• /
• v.29 no.2
• /
• pp.66-72
• /
• 2016

Porosity in polymer matrix composites increases rapidly during thermochemical decomposition at high temperatures. The generation of pores reduces elastic moduli and failure strengths of composite materials, and gas pressures in internal pores influence thermomechanical behaviors. In this paper, micromechanical finite element analysis is carried out by using two-dimensional representative volume elements for unidirectionally fiber-reinforced composites with porous matrix. According to the state of the pores, effective elastic moduli, poroelastic parameters and failure strengths of the overall composites are investigated in detail. In particular, it is confirmed that the failure strengths in the transvers and through-thickness directions are predicted much more weakly than the strength of nonpored matrix, and decrease consistently as the porosity of matrix increases.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.10
• /
• pp.3173-3185
• /
• 1996

Multi-model vibration control of laminated composites plates for various fiver orientations has been carried out by making use of piezolectric materials(PZT) as sensors and actuators. Cantilever plate is used as a specimen to test multi-modal vibration supression under random exitation. Impulse technique is applied to determine the natural frequency, the damping ratio(.zeta.) and the modal damping(2.zeta..omega.) of the first bending and the trosion modes. Two independent controllers are implemented to control the two modes simultaneously and established digitally on the basis of the direct negative velocity feedback control with collocated sensor/actuator. Experimental results for various fiber orientations and feedback gains are compared with finite element analysis considering stiffnesses and dampings of piezoeletiric sensors, actuators and bonding layer.

• Steel and Composite Structures
• /
• v.1 no.3
• /
• pp.329-340
• /
• 2001

Cyclic response of "shear" connections between steel outrigger beams and reinforced concrete core walls is presented in this paper. The connections investigated in this paper consisted of a shear tab welded onto a plate that was connected to the core walls through multiple headed studs. The experimental data from six specimens point to a capacity larger than the design value. However, the mode of failure was through pullout of the embedded plate, or fracture of the weld between the studs and plate. Such brittle modes of failure need to be avoided through proper design. A capacity design method based on dissipating the input energy through yielding and fracture of the shear tab was developed. This approach requires a good understanding of the expected capacity of headed studs under combined gravity shear and cyclic axial load (tension and compression). A model was developed and verified against test results from six specimens. A specimen designed based on the proposed design methodology performed very well, and the connection did not fail until shear tab fractured after extensive yielding. The proposed design method is recommended for design of outrigger beam-wall connections.

• Structural Monitoring and Maintenance
• /
• v.4 no.1
• /
• pp.1-15
• /
• 2017

Installation of sensors networks for continuous in-service monitoring of structures and their efficiency conditions is a current research trend of paramount interest. On-line monitoring systems could be strategically useful for road infrastructures, which are expected to perform efficiently and be self-diagnostic, also in emergency scenarios. This work researches damage detection in composite concrete-steel structures that are typical for highway overpasses and bridges. The techniques herein proposed assume that typical damage in the deck occurs in form of delamination and cracking, and that it affects the peak power spectral density of dynamic curvature. The investigation is performed by combining results of measurements collected by long-gauge fiber optic strain sensors installed on monitored structure and a statistic approach. A finite element model has been also prepared and validated for deepening peculiar aspects of the investigation and the availability of the method. The proposed method for real time applications is able to detect a documented unusual behavior (e.g., damage or deterioration) through long-gauge fiber optic strain sensors measurements and a probabilistic study of the dynamic curvature power spectral density.

• Structural Engineering and Mechanics
• /
• v.61 no.3
• /
• pp.325-334
• /
• 2017

In the present study, a numerical model for probability analysis of optimal design of fatigue non-uniform crack growth behaviour of a cracked aluminium 2024 T3 plate repaired with a bonded composite patch is investigated. The proposed 3D numerical model has advanced in literatures, which gathers in a unique study: problems of reliability, optimization, fatigue, cracks and repair of plates subjected to tensile loadings. To achieve this aim, a finite element modelling is carried out to determine the evolution of the stress intensity factor at the crack tip Paris law is used to predict the fatigue life for a give n crack. To have an optimal volume of our patch satisfied the practical fatigue life, a procedure of optimization is proposed. Finally, the probabilistic analysis is performed in order to a show that optimized patch design is influenced by uncertainties related to mechanical and geometrical properties during the manufacturing process.