• Journal of Power Electronics
• /
• 제19권6호
• /
• pp.1380-1392
• /
• 2019

Input filters are very important to matrix converters (MCs). They are used to improve grid side current waveform quality and to reduce the input voltage distortion supplied to the grid side. Due to the effects of the input filter and the output power, the grid side power factor (PF) is not at unity when the input power factor angle is zero. In this paper, the displacement angle between the grid side phase current and the phase voltage affected by the input filter parameters and output power is analyzed. Based on this, a new grid side PF unity compensation method implemented in the indirect space vector pulse width modulation (ISVPWM) method is presented, which has a larger compensation angle than the traditional compensation method, showing a higher grid side PF at unity in a wide output power range. Simulation and experimental results verify that the analysis of the displacement angle between the grid side phase current and the phase voltage affected by the input filter and output power is right and that the proposed compensation method has a better grid side PF at unity.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.119-122
• /
• 2000

This paper presents a new compensation method of series active power filter. The proposed method applied in the three-phase three-wire system can generate harmonic compensation voltage in front of the harmonic source. Futhermore it is also expended to three-phase four-wire system considering zero-sequence voltage. The compensation principle is described in detail. Experimental result show the validity of the proposed method in the three-phase three-wire system

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2010년도 하계학술대회 논문집
• /
• pp.170-171
• /
• 2010

The power loss due to PV module mismatch in PV array system is analyzed and a mismatch compensation method is proposed. A dc-dc converter is used to compensate for series mismatch caused by a low current module in a string. The converter is controlled to maximize the array power output. The proposed compensation method was verified by PSpice simulation.

• Journal of the Optical Society of Korea
• /
• 제20권1호
• /
• pp.13-21
• /
• 2016

Since the direct-gradient (DG) method uses the Shack-Hartmann wave front sensor (SH-WFS), based on the phase-conjugation principle, for atmospheric compensation in free-space optical (FSO) communication, it cannot effectively correct high-order aberrations. While the stochastic parallel gradient descent (SPGD) can compensate the distorted wave front, it requires more calculations, which is sometimes undesirable for an FSO system. A hybrid compensation (HC) method is proposed by properly using the DG method and SPGD algorithm to improve the performance of FSO communication. Simulations show that this method can well compensate wave-front aberrations and upgrade the coupling efficiency with few computations, preferable correction results, and rapid convergence rate.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제5권8호
• /
• pp.1423-1443
• /
• 2011

Background compensation plays an important role in detecting and isolating object motion in visual tracking. Here, we propose a Genetic Hough Transform, which combines the Hough Transform and Genetic Algorithm, as a method for eliminating background motion. Our method can handle cases in which the background may contain only a few, if any, feature points. These points can be used to estimate the motion between two successive frames. In addition to dealing with featureless backgrounds, our method can successfully handle motion blur. Experimental comparisons of the results obtained using the proposed method with other methods show that the proposed approach yields a satisfactory estimate of background motion.

• 한국태양에너지학회 논문집
• /
• 제29권1호
• /
• pp.58-63
• /
• 2009

In this paper, the power loss due to PV module mismatch in PV string is analyzed and a mismatch compensation method is proposed to improve the efficiency of PV system. The analysis of mismatch loss using PV model simulation reveals that the mismatch module may decrease the total efficiency because the MPPT function of power conditioner make the PV system operate at the local maximum point. The mismatch loss can be severe if the maximum power point current of mismatch module is less than that of string. The proposed compensation method which is simply implemented with a buck type converter shows the possibility to remove the mismatch loss. The effectiveness of the analysis and compensation method is verified by a prototype experiment.

• 한국산학기술학회논문지
• /
• 제14권1호
• /
• pp.28-32
• /
• 2013

본 연구에서는 프레스 부품의 스프링 백을 보정하기 위한 새로운 방법론을 제안하였다. 먼저, CAD 데이터와 측정데이터 사이의 오차를 비교하였다. 새로운 방법은 스프링 백을 보정하기 위한 수동적인 모델링 공정 대체가 가능한 3차원 측정데이터 기반의 자동 모델링을 제안하였다. 본 연구를 통해 프레스 부품의 스프링 백 보정을 위한 새로운 방법론을 적용하면 실제 공정에 소요되는 시간 및 비용 절감이 가능할 것으로 기대된다.

• 전력전자학회논문지
• /
• 제26권1호
• /
• pp.46-52
• /
• 2021

This study proposes a feedforward compensation control method to reduce 120 Hz output voltage ripple in a single-phase AC/DC rectifier system composed of PFC and LLC resonant converters. The proposed method compensates for the voltage ripple of the DC-link by using the AC input and DC output power difference, and then reduces the final output voltage ripple component of 120 Hz through feedforward compensation based on the linearized frequency gain curve of the LLC resonant converter. Through simulation and experimental results, the validity of the ripple reduction performance was verified by comparing the conventional PI controller and the proposed feedforward compensation method.

• 대한기계학회논문집B
• /
• 제27권11호
• /
• pp.1563-1571
• /
• 2003

This paper is the second part of several companion papers which compare the method of Air-fuel ratio(AFR) determination. In the previous paper, Eltinge chart was applied to the arbitrary fuel composition and the charts for gasoline, diesel, methanol, M85, liquefied petroleum gas(LPG), natural gas(NG), propane and butane were illustrated. In Eltinge chart, however, unburned hydrocarbon (UHC) is not used for determination of AFR. For improving accuracy, Eltinge suggested UHC compensation after the AFR reading in the chart. This compensation reduced the difference between real and reading value. In the compensation, however, the correction of oxygen and carbon dioxide is uncertain and there might be a mistake in conversion of UHC reading value. Therefore, the error is overestimated comparing with Spindt one which is most widely used. In addition, there is no comparison of the value with other useful methods. In this paper, the compensation of unburned HC was performed in Eltinge chart and the compensated value was compared with Spindts formula over wide range of AFR. The objects of investigating fuel are gasoline, methanol, NG and LPG. The result shows that Eltinge and Spindt method is flawlessly compatible and the difference between the two methods is under 0.3% in a λrange from 0.9 to 1.7. The method fur debugging instrumentation error is also presented.

• 한국군사과학기술학회지
• /
• 제21권4호
• /
• pp.508-519
• /
• 2018

This paper concerns on stabilization control of a gyro-stabilized 2-axes gimbal system which is mounted on a moving vehicles such as automobiles, armored vehicles, ships, flying vehicles, etc. A target image acquisition system is attached on the inner gimbal, and the gimbal systems are required to retain high stabilization accuracy in the absolute coordinate in order to provide fine target image while vehicle is moving. The stabilization control performance is hardly depended upon disturbance rejection ability of control, and disturbance feedforward compensation is effective because feedforward compensation reduce the amount of disturbance before the disturbance disturbs the systems. This paper suggests an experimental method which can estimate system parameters and disturbance torques by using 3-axes accelerometer mounted on the inner gimbal. Furthermore, a simple disturbance identification method which can be applied to any slanted base conditions has been suggested to identify mass unbalance vector and friction torques of each gimbal simultaneously. By using the estimated parameters, a feedforward compensation has been applied to the gyro-stabilized 2-axes gimbal system. The experimental results showed that the feedforward compensation based on the identification method suggested is effective to improve stabilization performances.