• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1197-1199
• /
• 2004

We have studied an optically compensated splay (OCS) mode driven by fringe electric field. The OCS configuration obtained by applying voltage to vertically aligned LCs shows a dark state when an optic axis of the OCS cell coincides with one of crossed polarizer axis. When the fringe electric field is applied, the LC director rotates in plane above whole electrode surface, giving rise to the high transmittance, the low operating voltage and wide viewing angle simultaneously.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.583-585
• /
• 2004

In this paper we will deal with a calibration method for low cost motion capture system using psd(position sensitive detection) optical sensor. To measure the incident direction of the light from LED emitted marker, the PSD is used the output current ratio on the electrode of PSD is proportional with the incident position of the light focused by lens. In order to defect the direction of the light, the current output is converted into digital voltage value by opamp circuits peak detector and AD converter with the digital value the incident position is measured. Unfortunately, due to the non-linearly problem of the circuit poor position accuracy is shown. To overcome such problems, we compensated the non-linearly by using least-square fitting method. After compensated the non-linearly in the circuit, the system showed more enhanced position accuracy.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.443-447
• /
• 2001

In this paper, a robust sensorless vector control system for induction motors with a speed estimator and an uncertainty observer is presented. At first, the proposed speed estimator is based on the MRAS(Mode Reference Adaptive System) scheme and constructed with a simple fuzzy logic(FL) approach. The structure of the proposed FL estimator is very simple. The input of the FL is the rotor flux error difference between reference and adjustable model, and the output is the estimated incremental rotor speed Secondly, the unmodeled uncertainties such as parametric uncertainties and external load disturbances are modeled by a radial basis function network(RBFN). In the overal speed control system, the control inputs are composed with a norminal control input and a compensated control input, which are from RBFN observer output and the modeling error of the RBFN, repectively. The compensated control input is derived from Lyapunov unction approach. The simulation results are presented to show the validity of the proposed system.

• Journal of the Korea Institute of Building Construction
• /
• v.5 no.4 s.18
• /
• pp.145-152
• /
• 2005

Long-term axial shortening of the vertical elements of tail buildings results in differential movements between two elements and may lead to the additional moments of connection beam and slab elements, and other secondary effects, such as cracks of partitions or curtain walls. Accurate prediction of time-dependent column shortening is essential for tall buildings from both strength and serviceability aspects. The compensation method is different from reinforced concrete and SRC(Steel Reinforced Concrete) members. The SRC columns are usually compensated according to total differential shortening between two vertical elements. In this study, column shortenings of 37-story W building under construction are predicted and compensated. The SRC column shortenings are compared with the actual column shortening by field measurement and the column shortenings are reanalysed and recompensated.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1698-1703
• /
• 2004

To understand the high expansion effects by adopting intake closing time in the cases of compensating intake air-mass and effective compression ratio simultaneously, fundamental study was carried out by using RICEM realizing Atkinson cycle. Intake air-mass and effective compression ratio were compensated by increasing supercharged pressure and geometric compression ratio. The results showed that the increasing rates of expansion ratio and expansion-compression ratio were increased by compensating both a intake air-mass and effective compression ratio the same tendencies were obtained with the increases of compression ratio and cut off ratio It was also found that LIVC has more advantages in expansion ratio and effective work than those of EIVC under above conditions.

• Journal of Sensor Science and Technology
• /
• v.3 no.1
• /
• pp.19-25
• /
• 1994

When etching rectangular convex corners of silicon using anisotropic etchants such as KOH, deformation of the edges always occurs due to undercutting. Therefore, it is necessary to correct the mass pattern for compensation. Experiments for the compensation method to prevent this phenomenon were carried out. In the result, the compensation pattern of a regular square is suitable for acceleration sensors considering space. With this consequence, silicon piezoresistive acceleration sensor with compensated square pillar type of mass has been fabricated using SDB wafer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04a
• /
• pp.49-50
• /
• 2008

OCB mode has advantages such as fast response time and wide viewing angle. But it has inevitable shortcoming which initial splay state must be changed to bend state. To overcoming this problem, OCB cell filled LC with RM monomer was cured by UV when voltage applied. Through previously mentioned methods, even if electric field is none, bend state was made by stabilized LC director. In this paper, we investigated the electric characteristics of polymer stabilized OCB mode.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2010.07a
• /
• pp.28-31
• /
• 2010

분산 비디오 부호화 시스템(distributed video coding:DVC)에서는 기존의 비디오 부호화 시스템과는 달리 부호기가 아닌 복호기에서 움직임 추정 연산을 함으로써 부호기의 복잡성을 크게 줄일 수 있다. DVC 시스템의 복호기에서 생성되는 부가정보(side information : SI)는 전체 DVC 시스템의 성능에 큰 영향을 미친다. DVC 시스템의 복호기에서 SI 정보를 생생하기 위해서 움직임 보상 보간(motion compensated interpolation : MCI) 기법이 많이 사용되는데 본 논문에서는 다양한 MCI 기법들의 성능을 분석한다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.12
• /
• pp.1101-1104
• /
• 2008

We have studied electro-optic characteristics to improve viewing angle of the in-plain switching (IPS) liquid crystal display using an compensation film. The IPS mode shows relatively large light leakage and color shift in diagonal directions in a dark state. To solve this problem, we have compensated the low contrast ratio in diagonal directions using one optimized discotic film and adjusting TAC films of polarizers. The compensated IPS mode shows wide viewing angle characteristics that region of CR 50:1 is over $60^{\circ}$ of polar angle in all directions. The optimized IPS cell exhibits much better performances than other methods do in terms of CR and color uniformity.

• Smart Structures and Systems
• /
• v.3 no.1
• /
• pp.115-131
• /
• 2007

The electromechanical integrated toroidal drive is a new drive system. For the control of the drive, the torque fluctuation and the steady-state errors should be removed and the fast response to the input change should be achieved. In this paper, the torque fluctuation of the drive system is analyzed and expressed as Fourier series forms. The transfer function of the torque control for the drive system is derived from its electromechanical coupled dynamic equations. A 2-DOF control method is used to control the drive system. Using definite parameter relationship of the 2-DOF control system, the steady errors of the torque control for the drive system is removed. Influences of the drive parameters on the control system are investigated. Using proper drive parameters, the response time of the control system is reduced and the quick torque response of the drive system is realized. Using a compensated input voltage, the torque fluctuation of the drive system is removed as well. The compensated input voltage can be obtained from the torque fluctuation equation and the transfer function. These research results are useful for designing control system of the new drive.