• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.545-550
• /
• 1997

It is well known that Statistical Energy Analysis(SEA) is one of very attractive analytical methods to solve shipboard noise problems. With reasonable successes, many applications of SEA to shipboard noise prediction have been reported. However when one wishes to obtain theoretical predictions by using SEA in practical systems, he will find difficulty in modeling of source systems, that is, foundations where to place main engine, generator, compressor, and so on. Also, he will find that it is hard to determine the amount of power flow from machinery to structures. In this paper, SEA of a simple foundation model was carried out using the estimated amount of power flow from source; the estimated mobility method. The comparison between the estimated and measured results is presented. That comparison shows a method to get structure-borne noise power from the combination of machinery and foundation. This prediction method gave a good results for a air-compressor mounted on a model foundation. The method is expected to give a reasonable power output in practical problems.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.982-986
• /
• 1998

The peak-power-tracking solar array regulator sensing the inductor current is proposed. Since it uses the inductor current as the solar array output power information, the PPT control scheme can be greatly simplified. The charge controlled two-loop scheme is presented to improve the dynamics due to the inductor current sensing. The comparison between the single-voltage loop controlled system and the two-loop controlled system employing the charge control is presented. This paper also contains the simulation results of that comparison.

• Journal of Applied Reliability
• /
• v.12 no.3
• /
• pp.177-186
• /
• 2012

This paper presents a comparison of the failure mechanism for high power converted white LEDs(3W) with the commercially available YAG:Ce and silicate phosphor. We carry out the normal aging life test for 10,000 hours, the high temperature aging test for 8,000 hours, the high temperature and humidity aging test for 8,000 hours and the current aging testing for 5,000 hours. The optical and electrical parameters of LEDs were monitored, such as lumen, correlated color temperature (CCT), chromaticity coordinates(x, y), thermal resistance, I -V curve and spectrum intensity. The stress induced a luminous flux decay on LED in all experiments and causes a failure. So we try to find out what's a main failure mechanism for a high power LED.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.216-219
• /
• 2008

The Power LED is more much than 1W and appliable to lights that is different from signal LED. In this paper we investigated types of tests in reliability assessment standards on Power LED. we make comparison of that military standards, JEITA(Japan Electronics and Information Technology Industries Association) and JEDEC(Joint Electron Device Engineering Council) with RS(reliability standard). Reliability tests should be considered that informations can be obtained from requirements of a real system Therefore, The paper aided companies to criteria for reliability tests by themselves.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.2
• /
• pp.302-317
• /
• 2017

This paper proposes a new full adder design based on pass-transistor logic that offers ultra-low power dissipation and superior variability together with low transistor count. The pass-transistor logic allows device count reduction through direct logic realization, and thus leads to reduction in the node capacitances as well as short-circuit currents due to the absence of supply rails. Optimum transistor sizing alleviates the adverse effects of process variations on performance metrics. The design is subjected to a comparative analysis against existing designs based on Monte Carlo simulations in a SPICE environment, using the 22-nm CMOS Predictive Technology Model (PTM). The proposed ULP adder offers 38% improvement in power in comparison to the best performing conventional designs. The trade-off in delay to achieve this power saving is estimated through the power-delay product (PDP), which is found to be competitive to conventional values. It also offers upto 79% improvement in variability in comparison to conventional designs, and provides suitable scalability in supply voltage to meet future demands of energy-efficiency in portable applications.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.11
• /
• pp.973-975
• /
• 2013

In this paper, the carrier-to-noise power ratio estimation performances for commercial GPS receiver are shown by simulation and are analyzed under weak signal reception, high sensitivity signal reception, and the matched spectrum jamming signal reception environments.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.37 no.E
• /
• pp.1-9
• /
• 1995

It is shown that two step power transformation is more efficient for the normalization of frequency distribution with the coefficient of skewness of zero in comparison with others including SMEMAX and power transformations. It is confirmed that the design low flows calculated using power and two step power transformations used in this study are generally nearer to the observed data as compared with those of SMEMAX transformation at all return periods in the applied watersheds of the Kum, Naktong and Yongsan rivers in Korea.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.237-240
• /
• 2000

A new control method using average comparison strategy have been proposed in this paper. This control method realizes sinusoidal input and output current. unity input displacement factor regardless of load power factor. Moreover compensation of the asymmetrical and harmonic containing input voltage is sautomatically realized and calculation time of control function is reduced.

• Journal of Hydrogen and New Energy
• /
• v.33 no.6
• /
• pp.707-714
• /
• 2022

Hydrogen production using solid oxide electrolysis cells (SOEC) is a promising technology because of its efficiency, cleanness, and scalability. Especially, high-power SOEC system has received a lot of attention from researchers. This study compared and analyzed the low-power and high-power SOEC system in term of economic. By using revenue requirement method, levelized cost of hydrogen (LCOH) was calculated for comparison. In addition, the sensitivity analysis was performed to determine the dependence of hydrogen cost on input variables. The results indicated that high-power SOEC system is superior to a low-power SOEC system. In the capital cost, the stack cost is dominant in both systems, but the electricity cost is the most contributed factor to the hydrogen cost. If the high-power SOEC system combines with a nuclear power plant, the hydrogen cost can reach 3.65 $/kg when the electricity cost is 3.28 ¢/kWh and the stack cost is assumed to be 574 $/kW.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2004.10a
• /
• pp.125-126
• /
• 2004