• Computers and Concrete
• /
• v.26 no.5
• /
• pp.385-395
• /
• 2020

The influence of combination of nano silica and silica fume, as partial cement replacement materials, on the properties of concrete has been studied through the measurement of compressive strength. The compressive strength of concrete in terms of mean, standard deviation and with-in-test coefficient of variation related to the variation in the nominated parameters have also been developed. The compressive strength data developed experimentally has been analyzed using normal-probability distribution and partial safety factors of composite concretes have been evaluated by using first order second moment approach with Hasofer Lind's method. The use of Nano silica and silica fume in concrete decreases the partial safety factor of concrete i.e., increase the reliability of concrete. The experimental results show that the properties of concrete having nano silica and silica fume in combination were better than that of a plain concrete. The SEM test results showing the level of Ca(OH)₂ in plain concrete and consumption level Ca(OH)₂ of concrete containing nano silica & silica fume have also been presented.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.5
• /
• pp.596-606
• /
• 2002

The three-dimensional unsteady compressible Euler equation solver with ALE, CFD code, PAM-FLOW based on FEM method has been applied to analyze the flow field around the high speed train which is entering into a channel. From the present study, the pressure and flow transients were calculated and analyzed. The generation of compression wave was observed ahead of train and the high pressure in the gap between the train and the tunnel was also found due to the blockage effects. It was found that abrupt fluctuation in pressure exists in the region from train nose to shoulder of train corresponding to 10％ of total length of train during tunnel entry. Computed time history of aerodynamic forces of train during tunnel entry show that drag coefficient rapidly rises and saturates at about non-dimensional time 0.31. The total increase of drag coefficient before and after tunnel entry is about 1.1%. Transient profile of lift force shows similar pattern to drag coefficient except abrupt drop after saturation and lift force in the tunnel increases 0.08% more than that before tunnel entry.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.19 no.5
• /
• pp.429-435
• /
• 2007

The present study proposed a method fer simulating reflective boundary conditions in Boussinesq wave propagation model by lining lateral boundaries like breakwaters and seawalls with artificial sponge layers. In order to find out the reflective characteristics of sponge layers, 1D numerical experiments were performed varying the relative sponge width (sponge width/wave length). The results showed that the reflection coefficient can be effectively realized from no reflection to full reflection simply by adjusting the relative sponge width. Based on the results, a multiple regression formula was proposed to delineate the relationship among the reflection coefficient and other dimensionless variables. Finally, the reflective sponge layer was applied to a semi-infinite breakwater, demonstrating that it can also be successfully employed in 2D applications.

• Journal of Welding and Joining
• /
• v.17 no.6
• /
• pp.84-89
• /
• 1999

Most of ferrous b.c.c weld materials may experience martensitic transformation during rapid cooling after welding. It is well known that volume expansion due to the phase transformation could influence on the relaxation of welding residual stress. To apply this effect practically, it is a prerequisite to establish a numerical model which is able to estimate the effect of phase transformation on residual stress relaxation quantitatively. For this purpose, the analysis is carried out in two regions. i.e., heating and cooling, because the variation of material properties following a phase transformation in cooling is different in comparison with the case in heating, even at the same temperature. The variation of material properties following phase transformation is considered by the adjustment of specific heat and thermal expansion coefficient, and the distribution of residual stress in analysis is compared with that of experiment by previous study. consequently, in this study, simplified numerical procedures considering phase transformation, which based on a commercial finite element package was established through comparing with the experimental data of residual stress distribution by other researcher. To consider the phase transformation effect on residual stress relaxation, the transition of mechanical and thermal property such as thermal expansion coefficient and specific heat capacity was found by try and error method in this analysis.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.48 no.1
• /
• pp.27-38
• /
• 2006

In this study, we developed a program to estimate discharge efficiently considering major hydraulic characteristic including water level, river bed, water slope and roughness coefficient in a natural river. Stream discharge was measured at Gongju gauge station located in the down stream of the Daechung Dam during normal and dry seasons from 2003 to 2004. The developed model was compared with the results from the existing rating curve at T/M gage stations, and was used for runoff analyses. Evaluating the developed river discharge estimation program, it was applied during 1983-2004 that base flow separation method and RRFS (Rainfall Runoff Forecasting System) which is based on SSARR (Streamflow Synthesis And Resevoir Regulation). The result presents the stage-discharge curve creator range at the Gong-ju is overestimated by approximately $10-20\%$, especially at the low stage. It is attributed to the hydraulic characteristics at the study. The discharge simulated by the RRFS and base flow separation, which is calibrated using the measurement at the early spring and late fall season during relatively d]v season, shows the least errors. The coefficient of roughness at Gongju station varied with the high and low water level.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.262-268
• /
• 2008

The present paper dealt with flow heat transfer characteristics of R-410A vaporization in horizontal smooth microchannel. The test sections were made of stainless steel tube with inner diameters of 300 mm and length of 300 mm. The refrigerant was supplied with mass flux range of 260-600 kg/$m^2s$ and applied under operating heat flux range of 5-20 kW/$m^2$ using a direct electric current heating method. The in let saturation temperature was set at $10^{\circ}C$ and vapor quality up to 1.0. The influences of mass flux, heat flux and inner tube diameter on local heat transfer coefficients were presented. Comparison with existing heat transfer coefficient correlations was performed. An improved heat transfer coefficient correlation for refrigerant vaporization in microchannel based on superposition model was developed with a mean deviation of 14.01%.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.5C
• /
• pp.403-412
• /
• 2008

This paper presents the methods which obtain the solution of Wiener-Hopf equation by LMS algorithm and get the coefficient of TDL filter in lattice filter directly. For this result, we apply an orthogonal input signal generated by lattice filter into an equivalent Wiener-Hopf equation and shows the scheme that can obtain the solution by using the MMSE algorithm. Conventionally, the method like aforementioned scheme can get an error and regression coefficient recursively. However, in this paper, we can obtain an error and the coefficients of TDL filter recursively. And, we make an theoretical analysis on the convergence characteristics of the proposed algorithm. Then we can see that the result is similar to conventional analysis. Also, by computer simulation, we can make sure that the proposed algorithm has an excellent performance.

• Journal of The Korean Digital Architecture Interior Association
• /
• v.12 no.2
• /
• pp.67-76
• /
• 2012

BIM and its quantity take-off widely apply to the construction projects and LCCO2 Assessment using the BIM's quantity take-off function can be tried recently. Because BIM modeling programs such as Revit and ArchiCAD do not provide adequate library for LCCO2 Assessment, quantity take-off data should be conversed and applied to Carbon Emission Coefficient using Excel program or manual work. Therefore, the purpose of this research is 1) to propose the Unit Conversion Systems for Carbon Emission Coefficient, 2) to provide basic library sets for BIM based LCCO2 Assessment method, and 3) to apply 11 material library sets on a apartment unit plan modeling to pursue the CO2 emission evaluation of the material production in the process of LCCO2 Assessment. Research results showed CO2 emission amount of 458.64kgCO2/m2 from the apartment unit plan modeling.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.8 no.2
• /
• pp.101-106
• /
• 2015

In this paper, to increase the throughput for wireless communication, FTN methods that is faster than Nyquist rate are used recently. To improve performance, turbo equalization algorithms that iteratively exchange probabilistic information between soft Viterbi equalizer and LDPC decoder to minimize ISI are applied in this paper. In FTN transmission, the performance depends on roll-off value and number of tabs of SRRC(Square Root Raised Cosine) filter. Therefore, Based on simulation, this paper present optimal number of filter coefficient and tab for various ISI factor of ${\tau}$.

• Journal of Information Processing Systems
• /
• v.17 no.4
• /
• pp.754-771
• /
• 2021

In the task of continuous dimension emotion recognition, the parts that highlight the emotional expression are not the same in each mode, and the influences of different modes on the emotional state is also different. Therefore, this paper studies the fusion of the two most important modes in emotional recognition (voice and visual expression), and proposes a two-mode dual-modal emotion recognition method combined with the attention mechanism of the improved AlexNet network. After a simple preprocessing of the audio signal and the video signal, respectively, the first step is to use the prior knowledge to realize the extraction of audio characteristics. Then, facial expression features are extracted by the improved AlexNet network. Finally, the multimodal attention mechanism is used to fuse facial expression features and audio features, and the improved loss function is used to optimize the modal missing problem, so as to improve the robustness of the model and the performance of emotion recognition. The experimental results show that the concordance coefficient of the proposed model in the two dimensions of arousal and valence (concordance correlation coefficient) were 0.729 and 0.718, respectively, which are superior to several comparative algorithms.