• Korean Chemical Engineering Research
• /
• v.52 no.4
• /
• pp.436-442
• /
• 2014

In this study, we developed an optical-fiber sensor using cobalt chloride solution to monitor temperature in real-time between long distance points unaffected by the electro-magnetic wave and the vibration. Cobalt chloride solutions were made using 10% water and 90% ethanol (v/v) solution. The transmittance of these solutions was analyzed on 655 nm using UV-Visible spectrometer regarding temperature change. Also 30.8 mM cobalt chloride solution was gelled by dissolving polyvinyl butyral and the transmittance of this was analyzed on 655 nm regarding temperature change. The results of transmittance and optical power measurement showed decrease of both transmittance and optical power with increase of temperature from 66.8% and 149.5 nW at $25^{\circ}C$ to 7.1% and 48 nW at $70^{\circ}C$, respectively. These results support the possibility of gelled cobalt chloride/polyvinyl butyral as an optical-fiber sensor to monitor temperature change.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.3
• /
• pp.587-592
• /
• 2023

Cobalt oxide (Co₃O₄·CoO) ultra fine particles were synthesized by liquid phase precursor method. cobalt(II) chloride hexahydrate (CoCl₂·6H₂O) was as a starting material. A plant-derived crystalline cellulose was used as impregnating materials. A impregnated precursor was calcined at a temperature of 350 to 900℃ to obtain cobalt oxide particles having a particle size of 1 to 10㎛. The crystallization process and morphology according to the calcination temperature were examined, and the properties of the synthesized powder were evaluated using SEM and XRD. It was confirmed that a crystal phase of Co₃O₄ began to form around 350℃ and crystal growth occurred up to 900℃. At a temperature above 500℃, the Co₃O₄ crystal was changed to another crystal phase CoO.

• Journal of the Korean Chemical Society
• /
• v.31 no.3
• /
• pp.231-235
• /
• 1987

In 10M chloride (4M HCl + 6M LiCl) solution, cobalt, but not nickel, formed complex anion (${CoCl_3}^-$), and this anion was extracted by a liquid anion exchanger with Amberlite LA-2. The ion exchange capacity was 2.175meq of cobalt complex per unit ml of Amberlite LA-2. Upon eluting the resin with 0.4M nitric acid, the cobalt complex was stripped and transfered into eluate quantitatively. By using this separation method in the chloride solution dissolved with 50mg of cobalt (II) and 500mg of nikel(II), recovery of cobalt were 99.6 percent.

• Korean Journal of Materials Research
• /
• v.26 no.11
• /
• pp.662-669
• /
• 2016

In order to identify changes in the nature of the particles due to changes in the inflow rate of the raw material solution, the present study was intended to prepare nano-sized cobalt oxide ($Co_3O_4$) powder with an average particle size of 50 nm or less by spray pyrolysis reaction using raw cobalt chloride solution. As the inflow rate of the raw material solution increased, droplets formed by the pyrolysis reaction showed more divided form and the particle size distribution was more uneven. As the inflow rate of the solution increased from 2 to 10 ml/min, the average particle size of the formed particles increased from about 25 nm to 40 nm, while the average particle size did not show significant changes when the inflow rate increased from 10 to 50 ml/min. XRD analysis showed that the intensity of the XRD peaks increased remarkably when the inflow rate of the solution increased from 2 to 10 ml/min. On the other hand, the peak intensity stayed almost constant when the inflow rate increased from 10 to 50 ml/min. With the increase in the inflow rate from 2 to 10 ml/min, the specific surface area of the particles decreased by approximately 20 %. On the contrary, the specific surface area stayed constant when the inflow rate increased from 10 to 50 ml/min.

• Korean Journal of Materials Research
• /
• v.24 no.1
• /
• pp.25-32
• /
• 2014

In this study, nano-sized cobalt oxide powder with an average particle size below 50 nm was prepared from a cobalt chloride solution by the spray pyrolysis process. The influences of reaction temperature on the properties of the generated powder were examined. The average particle size of the particles formed based on the spray pyrolysis process at a reaction temperature of $700^{\circ}C$ is roughly 20 nm. Moreover, most of these particles cannot appear with an independent type, thereby coexisting in a droplet type. When the reaction temperature increases to $800^{\circ}C$, the average particle size not only increases to roughly 40 nm but also shows a more dense structure while the ratio of particles which shows a polygonal form significantly increases. As the reaction temperature increases to $900^{\circ}C$, the distribution of the particles is from roughly 70 nm to 100 nm, while most of the particle surface is more intricately close and forms a polygonal shape. When the reaction temperature increases to $1000^{\circ}C$, the particle size distribution of the powder shows an existing form from 80 nm to at least 150 nm in an uneven form. As the reaction temperature increases, the XRD peak intensity gradually increases, yet the specific surface area gradually decreases.

• Journal of Powder Materials
• /
• v.10 no.4
• /
• pp.228-234
• /
• 2003

In the present study, the focus is on the synthesis of titanium carbide/cobalt composite powder by the spray thermal conversion process using metallic salt solution as the raw materials. Two types of oxide powders of Ti-Co-O system were prepared by the spray drying of two types of metallic salt solutions : titanium chloride-cobalt nitrate and $TiO_2$ powder-cobalt nitrate solutions. These oxide powders were mixed with carbon black, and then these mixtures were carbothermal reduced under a flowing argon atmosphere. The changes in the phase structure and thermal gravity of the mixtures during carbothermal reduction were analysed using XRD and TG-DTA. In the case of using the titanium chloride-cobalt nitrate solution, it could not be obtained TiC/Co composite powder due to contamination of the impurities during the spray drying of the solution. However, in tile case of using the $TiO_2$ powder-cobalt nitrate scullion, TiC-15 wt. %Co composite powder could be synthesized by the spray thermal conversion process. The synthesized TiC-15 wt. %Co composite powder at 120$0^{\circ}C$ for 2 hours has average particle size of 150 nm.

• Journal of the Korean Chemical Society
• /
• v.19 no.1
• /
• pp.53-64
• /
• 1975

The polymerization of methyl methacrylate initiated by cobalt(II) chloride in tetrahydrofuran has been studied. The conversion was increased liearly with polymerization time at initial stage of 6${\sim}$7% conversion and then the rate of polymerization was slightly reduced, and after that the autoacceleration was observed. The rate of polymerization was increased with the concentration of cobalt(Ⅱ) chloride, but at the concentration of cobalt(II) chloride higher than $3.4{\times}10^{-4}$ mole/l the rate of polymerization was decreased. The rate of polymerization was dependent on the 1.38 power of the concentration of methyl methacrylate. The effect of the radical inhibitor DPPH was observed and the inhibition time was increased with the concentration of DPPH. The apparent overall activation energy was calculated to be 13.2 kcal/mole. In the copolymerization of methyl methacrylate ($M_1$) and styrene ($M_2$), the monomer reactivity ratio was found to be $r_1$ = 2.35, $r_2$ = 0.78. From the above results. the initiation mechanism of polymerization was discussed and it was considered that the polymerization proceeds mainly via diradical mechaism.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.4 no.1
• /
• pp.43-70
• /
• 1994

The effects of potassium chromate (500ppm/500ppm), potassium dichromate (500ppm/500ppm), cobalt chloride (100ppm/10ppm), methylmercuric chloride (100ppm/10ppm) on the biosynthesis of phospholipid and their composition of fatty acids in E.coli and B.subtilis were analyzed. The contents of phosphatidylethanolamine, phosphatidylcholine, phosphatidylinositol, phosphatidylglycerol, cardiolipin and total lipids in treatment with metal compounds were lower to compare with the control. The major fatty acid utilized for biosynthesis of phospholipid was palmitic acid in control of E.coli and B.subtilis. However, in treatment with metal compounds, changes of fatty acid composition utilized for phospholipid formation were as follows. In E.coli major fatty acids were palimitic acid (ave. 26.26%) and cis-vaccenic acid (ave. 10.94%) in treatment with potassium chromate, palmitic acid (ave. 31.41%/31.42%) and stearic acid (ave. 17.92%/19.41%) in treatment with potassium dichromate and cobalt chloride. And in treatment with raethylmercuric chloride, palmitic acid (ave. 26.66%), stearic acid (ave. 15.50%) and cis-vaccenic acid (ave. 20.59%) were used in phospholipid formation. In B.subtilis, the major fatty acid was palmitoleic acid (ave. 15.29% /10.22%) in treatment with potassium chromate and cobalt chloride, and stearic acid (ave. 16.01%) in treatment with potassium dichromate. On the other hand, cis-vaccenic acid (ave. 9.09%), palmitic acid (ave. 17.23%), stearic acid (ave. 6.66%), myristic acid (ave. 6.34%) and lauric acid (ave. 4.75%) were analyzed into major fatty acids in treatment with methylmercuric chloride. As shown in results, specific fatty acid pattern was came out in treatment with metal compounds according to bacteria and treatments.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.4
• /
• pp.406-409
• /
• 1997

The various cobalt(Ⅱ) complexes were synthesized and characterized using tris-(2-benzimidazolylmethyl)amine (ntb) as a ligand where the ntb plays as a tripodal tetradentate ligand to form complexes with a trigonal pyramidal geometry. The complexes have 5 and 6 coordinate cobalt(Ⅱ) ions depending on the additional ligand used. In each complex the additional ligand, chloride anion, or acetate anion occupies the "open" site trans to the apical tertiary nitrogen atom of ntb ligand. Complex 1, [Co(Ⅱ)(ntb)Cl]Cl has a trigonal bipyramidal geometry. This geometry was easily constructed using ntb as a tetradentate ligand and chloride as a monodentate ligand. The complex is isostructural to the corresponding manganese(Ⅱ) complex. Crystal data are as follows: [Co(Ⅱ)(ntb)Cl]Cl·MeOH, 1. triclinic space group P1; a=13.524(2) Å, b=14.037(2) Å, c=17.275(1) Å; α=78.798(9), β=84.159(8)°, γ=65.504(9)°; V=2929.6(6) Å3; Z=4; R1=0.0715, wR2=0.1461 for reflections of I > 2σ(I). Six coordinate complex 2 [Co(ntb)(OAc)](OAc) was synthesized using ntb as a tetradentate ligand and acetate as a bidentate chelating ligand.

• Polymer(Korea)
• /
• v.29 no.4
• /
• pp.338-343
• /
• 2005

The thermal degradation of ABS/PC/triphenyl phosphate compounds in the presence of transition metal chloride catalysts has been studied by thermogravimetric analysis (TGA). The reaction of transition metal chloride catalysts (cobalt chloride, ferric chloride, nickel chloride and zinc chloride) and ABS/PC/triphenyl phosphate compounds has been found to occur during the thermal degradation of the compounds. In a nitrogen atmosphere, char formation is observed, and $3\~13\%$of the reaction product is non-volatile at $600^{circ}$. The resulting enhancement of char formation in a nitrogen atmosphere has been explained as a catalytic crosslinking effect of transition metal chloride catalysts. On the other hand, transition metal chloride catalyzed char formation of ABS/PC/triphenyl phosphate compounds in air was unsuccessful due to the oxidative degradation of the char at a higher temperature.