• Polymer(Korea)
• /
• v.32 no.4
• /
• pp.397-402
• /
• 2008

Perfluoropolyether(PFPE) has been widely applied in industry because of its very excellent properties of very high contact angle and low surface energy, good lubricant property and antifouling property. But the difficulty to synthesize PFPE has limited the research on this field. In this study, the novel silicon-containing oligomer with perfluoropolyether moiety was synthesized, and the structure was characterized by $^{19}F$-NMR and $^1H$-NMR. The surface properties of contact angle, sliding angle, and soil release property were investigated. The results show that PFPE in this study can be utilized as an anti-smudge coating material because it shows lower sliding angle and better soil release property than commercial products.

• Textile Coloration and Finishing
• /
• v.28 no.2
• /
• pp.92-100
• /
• 2016

To chemically prepare polypyrrole(pPy) coated fabrics(silk, cotton and nylon fabrics), the fabrics were first soaked in 0.4M oxidant $FeCl_3$/0.06M dopant anthraquinone-2-sulfonic acid solution for 5min at room temperature, and subsequently soaked in a 0.4M monomer pyrrole aqueous solution for 5min at room temperature. The content(wt%) of coated pPy in the coated fabrics was controlled by the number of treatments(these two steps). This study examined the effect of the number of treatments/pPy content on the sheet resistance, mechanical/bending properties and color behaviors of pPy coated fabrics. The coated pPy content, sheet resistance(${\Omega}$/square) and color strength(K/S) of pPy coated fabrics increased sharply with increasing number of treatments up to 20 times, while the increase slowed down afterward. The tensile strength, elongation at break and lightness($L^*$) decreased with increasing number of treatments. The tensile modulus and bending rigidity of coated fabrics increased significantly with increasing number of treatments/coated pPy content. This indicated that the flexibility of coated fabrics decreased considerably.

• Polymer(Korea)
• /
• v.39 no.3
• /
• pp.499-505
• /
• 2015

Polyorganosiloxane having controlled cross-linking density and phenyl group content were prepared by dimethyldimethoxysilane (DMDMS), methyltrimethoxysilane (MTMS) and phenyltrimethoxysilane (PTMS). The effect of cross-linking density and phenyl group content on the physical properties of siloxane resin and its coated film have been invetigated. Si-NMR results confirmed that synthesized siloxane resins have equivalent D $T^{Me}$ $T^{Ph}$ structures according to applied mole ratios of DMDMS, MTMS and PTMS. Polyorganosiloxane having higher cross-linking density with high phenyl content showed the high molecular weight and increasing phenyl content resulted in higher refractive index as well as better thermal stability. Cross-linking density is more important factor than phenyl content to obtain higher pencil hardness of coated film on the glass. Our results concluded that even polyorganosiloxanes having similar siloxane structures show different physical properties as function of cross-linking density and phenyl content in polyorganosiloxane.

• Fire Science and Engineering
• /
• v.26 no.6
• /
• pp.45-50
• /
• 2012

The spalling causes the sever reduction of the cross sectional area with the exposure of the reinforcing steel, which originates a problem in the structural behaviour. By coating surface of high strength concrete with fireproof mortar, the high strength concrete is protected from the spalling in fire and the method to constrain the temperature increase of steel bar within the concrete. The purpose of this study is to investigate the temperature history properties of lightweight mortar using perlite and polypropylene fiber for fire protection covering material. For this purpose, selected test variables were the contents and length of polypropylene fiber. As a result of this study, it has been found that addition of polypropylene fiber to mortar modifies its pore structure and this causes the internal temperature to rise. And it has been found that a new lightweight mortar can be used in the fire protection covering material.

• Applied Chemistry for Engineering
• /
• v.27 no.4
• /
• pp.449-454
• /
• 2016

In this study, highly monodispersed porous carbon microcapsules with a hollow core were synthesized using polystyrene (PS) beads as a hard template. The surface of PS was first modified with polyvinylpyrollidone (PVP) for the easy attachment of inorganic silica sol. After coating the surface of PVP modified PS microspheres with SBA-16 sol, the carbon microcapsules with a hollow macroporous core were fabricated through reverse replication method by filling carbon sources in the mesopores of silica mold. The hollow carbons having a mesoporous shell structure and narrow particle size distribution could be obtained after the carbonization of carbon source and the dissolution of silica mold by HF solution. The mesoporous characteristics and electrochemical properties of hollow carbon microcapsules were characterized by XRD, SEM, TEM, $N_2$ adsorption/desorption analysis and cyclic voltammetry. They showed the high electric conductivity and capability for use as efficient electro-materials such as a supercapacitor.

• Korean Journal of Materials Research
• /
• v.19 no.11
• /
• pp.631-636
• /
• 2009

We investigated the NO gas sensing characteristics of ZnO-carbon nanotube (ZnO-CNT) layered composites fabricated by coaxial coating of single-walled CNTs with a thin layer of 1 wt% Al-doped ZnO using rf magnetron sputtering deposition. Morphological studies clearly revealed that the ZnO appeared to form beadshaped crystalline nanoparticles with an average diameter as small as 30 nm, attaching to the surface of the nanotubes. It was found that the NO gas sensing properties of the ZnO-CNT layered composites were dramatically improved over Al-doped ZnO thin films. It is reasoned from these observations that an increase in the surface-to-volume ratio associated with the numerous ZnO “nanobeads” on the surface of the CNTs results in the enhancement of the NO gas sensing properties. The ZnO-CNT layered composite sensors exhibited a maximum sensitivity of 13.7 to 2 ppm NO gas at a temperature of 200${^{\circ}C}$ and a low NO gas detection limit of 0.2 ppm in dry air.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.11
• /
• pp.1239-1243
• /
• 2014

This paper presents the application of carbon-fiber-reinforced polymer (CFRP) for the damage absorption and optimal design of portable smart devices to close in life. CFRP specimens are subjected to a tensile test to estimate their mechanical properties in terms of the stacking angles. Further, the screw reverse torque and screw torque at each stacking angle are determined using a torque tester after tapping holes on the CFRP specimens. Two experiments are performed for comparing their results in order to determine optimal conditions. In the tensile test, a woven specimen is found to have the highest strength and stiffness. In the case of the woven specimen, no difference is observed even when it is applied to prevent loosening of the coating. And average result value was excellent.

• Journal of the Korean Society for Heat Treatment
• /
• v.22 no.5
• /
• pp.307-311
• /
• 2009

In this study, TiCrN films were deposited on STS 316 Land Si (100) wafer by inductively coupled plasma (ICP) assisted D.C. magnetron sputtering. The effect R.F. power for ICP discharge on the mechanical properties of TiCrN films was investigated. XRD, XPS and FE-SEM were used for the structure analysis. Also the Micro-Knoop hardness tester and profilometer were used for measuring hardness of coatings and film stress respectively. As increasing the R.F. power for ICP discharge, thickness of coating was decreased from 1633 nm to 1288 nm but hardness was increased about $Hk_{5g}$ 4200 at 400 W. All of the XRD patterns showed (111), (200) and (220) peaks of TiCrN films. Surface morphology was studied using the profilometer. FE-SEM was used to know morphology and cross-section of the films. Structure of the films was changed dense as increased ICP power.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.27 no.5
• /
• pp.683-687
• /
• 2013

Evacuation disorder(ED) is frequently observed in the elderly people. In this study, we investigated the tongue color properties in the elderly. 327 subjects were participated in this study and classified into normal group (n=95) and ED group (n=23) by two Korean Oriental Medicine doctors. The tongue images were acquired by using computerized tongue diagnosis system, and its color were linearly corrected base on CIE $L^*a^*b^*$ values of 12 color samples. The tongue region was segmented from acquired image and divided into two regions along the vertical direction. In order to estimate color properties of the tongue, a color histogram was calculated for the root region based on the CIE $L^*$ and $a^*$ values, and differences of color histogram values between normal and ED groups were computed based on the Mann-Whitney U test. As results, pixels corresponding to typical colors of the pale tongue and thin tongue coating were significantly more distributed in ED than those in normal group(p<0.05). The tongue color of the root region in ED was revealed to be different from those in healthy subjects.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.1
• /
• pp.41-47
• /
• 2010

Increasing ash content of the paper is one of the most effective methods for saving raw materials and steam consumption and improving optical properties and better print quality. However, the increase of filler loading or filler content using a conventional wet end system is limited due to severe loss in strength properties, affecting runnability and product quality. This is because the filler has no ability to make bonding with cellulosic fibers. Therefore, if the technology to give filler the bonding ability is developed, the ash content of the paper can be increased more than ever. This study was carried out to modify PCC by coating its surface with starch contributing to better bonding with fibers. To prepare the modified PCC, cationic starch was selected as a polymer and then pretreatment was done by mixing PCC and cationic starch. Consequently, the pretreated PCC contributed to higher tensile strength, stiffness and opacity than the conventional filler, such as GCC and untreated PCC. However, CIE whiteness and ISO brightness decreased slightly compared to conventional fillers.