• Journal of Surface Science and Engineering
• /
• v.37 no.4
• /
• pp.208-214
• /
• 2004

The influence of the boron content on the various properties of Ni-B alloy films produced by electrodeposition was investigated. The considerable reduction in grain size was observed with increasing boron content. The internal stress was tensile and increased linearly with increasing boron content. Hardness increased up to $750H_{v}$ at 2 at% boron and then kept the value to 11 at% boron for as-plated Ni-B coatings. The hardness of Ni-B films increased up to $1,250H_{v}$ due to the intermetallic$ Ni_3$B precipitation by the heat treatment, and maximum hardness of each coating increases with boron content. Wear resistance decreased with increasing the boron content because of high friction coefficient and brittle fracture of film which has higher content of boron.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.1
• /
• pp.88-93
• /
• 2004

Electrochemical impedance spectroscopy was used to evaluate the anticorrosive properties of resin(alkyd, epoxy, urethane) and pigment(hydroxy apatite(HAp), zinc potassium chromate(ZPC). red lead(RL)). The corrosion behavior of coatings applied on steel has been investigated during exposure to 0.5M-NaCl The anticorrosive performances of resins were found to depend on their chemical nature and decreased in the order of urethane > epoxy > alkyd resin coating. Hydroxy apatite and zinc potassium chromate pigment which have property to passivate the substrate showed relatively high anticorrosive performance.

• ETRI Journal
• /
• v.31 no.6
• /
• pp.636-641
• /
• 2009

ZnO nanofibers were electro-spun from a solution containing poly 4-vinyl phenol and Zn acetate dihydrate. The calcination process of the ZnO/PVP composite nanofibers brought forth a random network of polycrystalline wurtzite ZnO nanofibers of 30 nm to 70 nm in diameter. The electrical properties of the ZnO nanofibers were governed by the grain boundaries. To investigate possible applications of the ZnO nanofibers, their CO and $NO_2$ gas sensing responses are demonstrated. In particular, the $SnO_2$-deposited ZnO nanofibers exhibit a remarkable gas sensing response to $NO_2$ gas as low as 400 ppb. Oxide nanofibers emerge as a new proposition for oxide-based gas sensors.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.1
• /
• pp.33-37
• /
• 2013

The properties of LTCC green sheets formed by the MLS-22 powder of NEG Inc. were investigated for acrylic binders with different PVB and Tg in the variation of temperature. The elongation of the green sheets showed large variation depending on the temperature, and was rapidly decreased near the Tg of the sheets. With the increase of the ratio of plasticizer/binder (P/B), large elongation of the sheets was observed due to the decrease of the Tg. In the stacking process of the multilayer ceramic, the optimal control of the temperature is highly required depending on the Tg of the binder and the ratio of P/Buniform coating.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1988.10a
• /
• pp.29-32
• /
• 1988

Polycrystalline CdS films were prepared by coating a slurry, which consisted of Cds, 11w/o of CdCl$_2$ and various amounts of InCl$_3$on the glass substrate and by sintering in a nitrogen atmosphere. Measurements on the electrical and optical Properties and observation on the microstructure of the sintered films were made. It was observed that the carrier concentration in the films remains almost constant on the addition of InCl$_3$. Optical transmittance remains constant on the addition of InCl$_3$ up to 3w/o but it decreases with further increase in InCl$_3$.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.6
• /
• pp.658-663
• /
• 2009

Metal/ceramic composites structures have many attractive properties with great potential for applications that demand high stiffness as well as chemical and biological stability, thermal and electrical insulation. They are currently in use for mechanical and thermal protection in cutting tool and engine parts. Thus, determination of adhesive properties for coating part is one of the most important problems for the extension of the use of coated materials. In this work, bending strength of Functionally Graded Materials(FGM) are evaluated by means of bending strength tester. The graded layer according to the load condition showed the change of the bend strength.

• YAKHAK HOEJI
• /
• v.39 no.6
• /
• pp.593-599
• /
• 1995

Erythromycin was formulated as enteric-coated pellets in order to reduce degradation in stomach and gastromtestmal irritation, and to maximize the absorption in intestine followmg its oral administration. Core pellets were prepared using fluid-bed granulator with two different methods (powder layering and solvent spraying) and enteric-coated with two different coating polymers (HPMCP and Eudragit E30D). Physical characteristics md dissolution rates of core pellets and enteric-coated pellets were evaluated to optimize the formulation. Powder layering method resulted in shorter initial dissolution time than solvent spraying method, but physicochmical properties of the product were worse than solvent spraying method with respect to hardness, ftiability and density. The dissolution rate of the drug was increased with the addition of surfactants, showing concentration-dependence. The scanning electron microscopic observation of pellets revealed significant differences on the surface appearances prepared with solvent spraying method. The core pellet made with powder layering method had crystals on the surface, which resulted in poor physical properties of the pellets. The dissolution profiles of erythromycin pellets coated with HPMCP or Eudragit L30D were close to that of commercially available erythromycin enteric-coated product.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.4
• /
• pp.1235-1241
• /
• 2012

Aluminium (Al)-doped zinc oxide (AZO) thin films with different Al concentrations were prepared by the solgel spin-coating method. Optical parameters such as the optical band gap, absorption coefficient, refractive index, dispersion parameter, and optical conductivity were studied in order to investigate the effects of the Al concentration on the optical properties of AZO thin films. The dispersion energy, single-oscillator energy, average oscillator wavelength, average oscillator strength, and refractive index at infinite wavelength of the AZO thin films were found to be affected by Al incorporation. The optical conductivity of the AZO thin films also increases with increasing photon energy.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.4
• /
• pp.902-906
• /
• 2009

It is found that that the coating N-acetyl cysteine (NAC) on gold surfaces may be used to design the distribution of either gold particle adsorbed to the $TiO_2$ surface or vice versa by adjusting the electrostatic interactions. In this study, we investigated electrostatic properties of the NAC-coated-gold surface and the $TiO_2$ surface. The surface forces between the surfaces were measured as a function of the salt concentration and pH value using the AFM. By applying the Derjaguin-Landau-Verwey-Overbeek (DLVO) theory to the surface forces, the surface potential and charge density of the surfaces were quantitatively acquired for each salt concentration and each pH value. The surface potential and charge density dependence on the salt concentration was explained with the law of mass action, and the pH dependence was with the ionizable groups on the surface.

• Corrosion Science and Technology
• /
• v.9 no.1
• /
• pp.16-19
• /
• 2010

Application of ultra-high strength steel sheets is one of the most important methods to satisfy weight reduction and crash safety of a vehicle. Recently, there has been a trend to apply ultra-high strength steel sheets widely to underbody parts in which corrosion resistance is required. In this work, ultra-high strength galvannealed steel sheets with a tensile strength of 1180 MPa were developed. Newly developed ultra-high strength galvannealed steel sheets have comparable properties, such as mechanical properties, spot weldability, crashworthiness and adhesion of coatings, to conventional steel sheets.