• 한국분말재료학회지
• /
• 제23권6호
• /
• pp.437-441
• /
• 2016

Recently, the grain boundary diffusion process (GBDP), involving heavy rare-earth elements such as Dy and Tb, has been widely used to enhance the coercivity of Nd-Fe-B permanent magnets. For example, a Dy compound is coated onto the surface of Nd-Fe-B sintered magnets, and then the magnets are heat treated. Subsequently, Dy diffuses into the grain boundaries of Nd-Fe-B magnets, forming Dy-Fe-B or Nd-Dy-Fe-B. The dip-coating process is also used widely instead of the GBDP. However, it is quite hard to control the thickness uniformity using dip coating. In this study, first, a $DyF_3$ paste is fabricated using $DyF_3$ powder. Subsequently, the fabricated $DyF_3$ paste is homogeneously coated onto the surface of a Nd-Fe-B sintered magnet. The magnet is then subjected to GBDP to enhance its coercivity. The weight ratio of binder and $DyF_3$ powder is controlled, and we find that the coercivity enhances with decreasing binder content. In addition, the maximum coercivity is obtained with the paste containing 70 wt% of $DyF_3$ powder.

• Journal of Magnetics
• /
• 제11권3호
• /
• pp.126-129
• /
• 2006

The phosphate coating on the $(Fe_{0.97}Cr_{0.03})_{76}(Si_{0.5}B_{0.5})_{22}C_2$ amorphous powders with an average size of 10 ${\mu}m$ in diameter has been carried out in aqueous 1.0-2.0 wt% $H_3PO_4$ solutions, and the consolidation behavior and magnetic properties of their compressed powder cores has been investigated. The phosphate coating could provide efficient electrical insulation between amorphous powders and improved consolidation ability at room temperature. Especially when the powders were treated in more concentrated phosphoric acid solution, enhanced phosphate covering and higher frequency/dc-bias stability were achieved. The powder cores phosphate-coated in 2.0 wt% $H_3PO_4$ solution exhibited constant permeability of 21 up to 10 MHz, 110 of the quality factor at 0.9 MHz, 610 mW/cm3 core loss at 100 kHz/0.1 T and 89 of percent permeability at 100 kHz.

• 한국분말재료학회지
• /
• 제21권5호
• /
• pp.377-381
• /
• 2014

This work describes the coloration, chemical stability of $SiO_2$ and $SnO_2$-coated blue $CoAl_2O_4$ pigment. The $CoAl_2O_4$, raw materials, were synthesized by a co-precipitation method and coated with silica ($SiO_2$) and tin oxide ($SnO_2$) using sol-gel method, respectively. To study phase and coloration of $CoAl_2O_4$, we prepared nano sized $CoAl_2O_4$ pigments which were coated $SiO_2$ and $SnO_2$ using tetraethylorthosilicate, $Na_2SiO_3$ and $Na_2SiO_3$ as a coating material. To determine the stability of the coated samples and their colloidal solutions under acidic and basic conditions, colloidal nanoparticle solutions with various pH values were prepared and monitored over time. Blue $CoAl_2O_4$ solutions were tuned yellow color under all acidic/basic conditions. On the other hand, the chemical stability of $SiO_2$ and $SnO_2$-coated $CoAl_2O_4$ solution were improved when all samples pH values, respectively. Phase stability under acidic/basic condition of the core-shell type $CoAl_2O_4$ powders were characterized by transmission electron microscope, X-ray diffraction, CIE $L^*a^*b^*$ color parameter measurements.

• 전기화학회지
• /
• 제12권2호
• /
• pp.162-166
• /
• 2009

탄소 피복된 Si/Cu 분말을 기계적인 볼-밀링(ball-milling) 방법과 고온에서 탄화수소가스 분해 방법에 의해 제조하여 리튬이차전지용 음극으로 사용하였고 이에 대한 전기화학적 거동을 조사하였다. 천연흑연(natural graphite)을 이용하여 탄소 피복된 Si/Cu/graphite 복합체 음극소재를 제조하였으며 천연흑연 음극소재와 전기화학적 특성을 비교하였다. 탄소 피복된 Si/Cu 음극의 가역적 비용량은 초기 10 싸이클까지 지속적인 증가를 나타냈다. 탄소 피복된 Si/Cu/graphite 복합체 음극의 가역적 비용량은 $0.25mA/cm^2$ 전류밀도에서 450mAh/g이고 초기 싸이클 효율은 81.3%로 나타났다. 복합체 음극의 싸이클 성능은 가역적인 비용량값을 제외하고 천연흑연 음극과 유사하게 나타났다.

• 한국세라믹학회지
• /
• 제46권2호
• /
• pp.189-199
• /
• 2009

The Powder characteristics and sintering behavior of $SiO_2$ coated $BaTiO_3$ were studied. $BaTiO_3$ powders were synthesized by the liquid mix method developed by Pechini, and silica coating was prepared by alkoxide hydrolysis method with TEOS and ethanol. The particle size of the $BaTiO_3$ powders was 35 nm and the thickness of the $SiO_2$ coating layer was 5 nm. As the $SiO_2$ content increased, the $SiO_2$ layers improved the powder dispersion by increasing electrostatic repulsion between the $BaTiO_3$ particles. Effects of MgO coating on microstructure and dielectric properties of $BaTiO_3$ have been studied compared with mechanically MgO mixed $BaTiO_3$. MgO coated $BaTiO_3$ particles were prepared by a homogeneous precipitation method using $MgCl_2\cdot 6H_2O$ and urea. MgO coated $BaTiO_3$ exhibited homogeneous microstructure compared with mixed samples. XRD analysis revealed that Mg substitution for the Ti site in the MgO mixed sample was much greater than in the coated one. Electrical properties of MgO mixed and coated $BaTiO_3$ were affected by the diffusion behavior of Mg in $BaTiO_3$ lattice.

• 한국세라믹학회지
• /
• 제43권12호
• /
• pp.781-787
• /
• 2006

NiO-coated YSZ powder was prepared using heterogeneous precipitation of Ni hydroxides on YSZ particle surface and high energy milling. The powders were characterized by TG/DTA, XRD, XPS, and SEM. Amorphous Ni precipitate completely decomposed into NiO at $500^{\circ}C$ and the growth of NiO crystallites was constrained by the core particles. Nanocrystalline NiO-coated YSZ core-shell structure powder could be obtained after calcination at $800^{\circ}C$ for 2 h. A core-shell powder compact, due to high sinterability, showed a near theoretical density at $1350^{\circ}C$. After reduction at $900^{\circ}C$, interpenetrating Ni-YSZ microstructure with very uniformly distributed fine Ni and YSZ grains and pores was observed. In contrast, the mechanically mixed oxide sample showed less uniform distribution of pores and larger discontinuous We particles as compared with the core-shell samples.

• Journal of Periodontal and Implant Science
• /
• 제30권1호
• /
• pp.167-180
• /
• 2000

The present study evaluated the effects of guided tissue regeneration using biodegradable membrane, with and without calcium-phosphate thin film coated deproteinated bone powder in beagle dogs. Contralateral fenestration defects(6 × 4 mm) were created 4 mm apical to the buccal alveolar crest on maxillary canine teeth in 5 beagle dogs. Ca-P thin film coated deproteinated bone powder was implanted into one randomly selected fenestration defect(experimental group). Biodegradable membranes were used to provide bilateral GTR. Tissue blocks including defects with overlying membranes and soft tissues were harvested following a four- & eight-week healing interval and prepared for histologic analysis. The results of this study were as follows. 1.......The regeneration of new bone, new periodontal ligament, and new cementum was occurred in experimental group more than control group. 2.......The collapse of biodegradable membranes into defects were showed in control group and the space for regeneration was diminished. In experimental group, the space was maintained without collapse by graft materials. 3........In experimental group, the graft materials were resorbed at 4 weeks after surgery and regeneration of bone surrounding graft materials was occurred at 8 weeks after surgery. 4.......Biodegradable membranes were not resorbed at 4 weeks and partial resorption was occurred at 8 weeks but the framework and the shape of membranes were maintained. No inflammation was showed at resorption. In conclusion, the results of the present study suggest that Ca-P thin film coated deproteinated bone powder has adjunctive effect to GTR in periodontal fenestration defects. Because it has osteoconductive property and prohibit collapse of membrane into defect, can promote regeneration of much new attachment apparatus.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1167-1168
• /
• 2006

In this study, the pure iron powder was treated with aqueous phosphoric acid to produce phosphate insulating layer on the surface. After drying the powder, it was compacted in a mold with a diameter of 20mm at 800MPa. The powder compacts were then heat treated at $500^{\circ}C$ for 1 hour. The results showed that insulated iron powder was obtained with uniform phosphate layer by chemical reaction. With increased amount of phosphate layer, the core loss and density of compacts were decreased. It was also found that the addition of ethyl alcohol during insulating reaction resulted in improved core loss value.

• 한국분말재료학회지
• /
• 제15권6호
• /
• pp.477-481
• /
• 2008

Formation and characteristics of spraying powder for BSCCO High-Tc superconductor prepared by plasma spray coating were investigated. The addition of 3% of binder gives the best flowability of the powder. Ball milling for 30h and 35h gives the best flowability of powder in the case of 2001 and 0212, respectively. The withdraw ratio increases upon binder addition from 12 to 27% in the case of 2001 and from 18 to 31% in the case of 0212 for sieving powder of $30-90{\mu}m$ in size. The built-up efficiency for $100{\mu}m$ thickness of spray coating is increased more than 30% by binder addition. The microstructure of the spray coated layers was investigated by XRD and EDS analysis.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.156-158
• /
• 2002

BSCCO tpaes with insulating ceramic barriers such as Zr$O_{2}$, $Al_{2}$$CO_{3}$, and Sr$CO_{3}$ were fabricated and their electrical properties were evaluated. Each filament was dip coated with ceramic slurries and then made 19 multifilamentary tapes by the “powder-in-tube” process. Microstructural investigation showed that filaments were completely decoupled each other and had a significant sausage effect. The critical current of coated tapes was reduced compared to that of non coated one, and its reduction was varied with the coating materials. For tapes with coated with Sr$CO_{3}$, the critical current was measured to be 7.2 A which was 44% reduction to that of non coated one. This reduction is believed to be due to the formation of sausage effect and non-uniform microstructure.