• Journal of Ship and Ocean Technology
• /
• v.5 no.3
• /
• pp.1-13
• /
• 2001

Present-day rules and regulations for the design and construction of ships are almost without exemption of a prescriptive and deterministic nature. Often it is argued that this situation is far from ideal; it does no right to the advances, which have been made during the past decades in engineering tools in marine technology, both in methodology and in computational power. Within IMO this has been realized for some time and has resulted in proposals to use Formal Safety Assessment(FSA) as a tool to improve and to modernize the rule making process. The present paper makes use of elements of the FSA methodology, but instead of working towards generic regulations or requirements, a Risk Assessment Approach, not unlike a 'safety case'; valid for a certain ship or type of ship is worked out. Delft University of Technology investigated the application of safely assessment procedures in ship design, in co-operation with Anthony Veder Shipowners and safety experts from Safely Service Center BV. The ship considered is a semi-pressurized-fully refrigerated LPG carrier. On the basis of the assumption that a major accident occurs, various accident, scenarios were considered and assessed, which would impair the safety of the carrier. In a so-called Risk Matrix, in which accident frequencies versus the consequence of the scenarios are depicted, the calculated risks all appeared lo be in the ALARP('as low as reasonable practicable') region. A number of design alternatives were compared, both on safety merits and cost-effectiveness. The experience gained with this scenario-based approach will be used to establish a set of general requirements for safety assessment techniques in ship design. In the view that assessment results will be most probably presented in a quasi-quantified manner, the requirements are concerned with uniformity of both the safety assessment. These requirements make it possible that valid comparison between various assessment studies can be made. Safety assessment, founded on these requirements, provides a validated and helpful source of data during the coming years, and provides naval architects and engineers with tools experience and data for safety assessment procedures in ship design. However a lot of effort has to be spent in order to make the methods applicable in day-to-day practice.

• Journal of Korean Society of Forest Science
• /
• v.102 no.2
• /
• pp.189-197
• /
• 2013

The Cancun Agreements under the United Nations Framework Convention on Climate Change require developing countries aiming to undertake REDD+ activities to develop a national strategy or action plan, addressing the drivers of deforestation and forest degradation, a measurement, reporting and verifying (MRV) system including forest monitoring system, and safeguards to ensure equity and co-benefits for local communities and indigenous peoples, and biodiversity. The Government of Indonesia and the Government of Norway established REDD+ cooperation through signing a 'Letter of Intent' in May, 2010. Indonesia agreed on 'a two year suspension on all new concessions for conversion of peat and natural forest'. In turn, Norway agreed to support Indonesia's REDD+ implementation efforts up to one billion United States dollars. Indonesia's REDD+ national strategy (June, 2012) accepted most of the requests included in the 'Letter of Intent'. The REDD+ national strategy, however, does not reflect requests of the Cancun Agreements which noted identification of the drivers of deforestation and forest degradation and guarantee of real greenhouse gas emissions reductions. Indonesia lays emphasis on Norwegian requests which includes expected financial support rather than the Cancun Agreements which have a weak legally-binding requirements.

• Preventive Nutrition and Food Science
• /
• v.8 no.2
• /
• pp.166-172
• /
• 2003

Calcium lactate (CL) prepared from powdered black snail (PBS) or its ashed powder (ABS), was investigated for ideal manufacturing conditions to optimize color, solubility and sensory quality. Based on the amount of PBS and 100 mL lactic acid (LA), the yields of PBS-CL were 300% and 15 g in 10% LA and 260% and 20 g in 20% LA. Yields of ABS-CL based on the amount ABS and 100 mL LA were 400% and 60 g in 10% LA and 329% and 66 g in 20% LA. Both of the yields were decreased with an increase of the LA concentration on the basis of PBS and ABS amounts, but proportionally increased with the increment in the LA concentration on the basis of LA volume. Optimal preparation times of the dehydrated PBS-CL and ABS-CL were, respectively, 4 hr and 5 hr at 10$0^{\circ}C$, 3 hr and 4 hr at 12$0^{\circ}C$, and 1 hr and 2 hr at 15$0^{\circ}C$, which showed shorter time in preparing the dehydrated ABS-CL. PBS-CL and ABS-CL were confirmed to be Ca($CH_3$CHOH$CO_2$)$_2$ by the analysis results of IR and $^1$H-NMR. Calcium contents of the anhydrous PBS-CL and ABS-CL were individually 15.4% (w/w) and 17.3% (w/w) representing 84.2% and 94.5% or each theoretical value. Colors or PBS-CL and ABS-CL were light yellow and light-greenish white each. Solubilities of PBS- CL and ABS-CL in distilled water at pH 3~8 were 5.43 and 6.11 g/100 mL, respectively, which demonstrated higher mean solubilities rather than the 4.74 g/100 mL of standard CL. Solubilities of PBS-CL (3.14~5.03 g/100 mL) and ABS-CL (4.69~6.05 g/100 mL) against soup soy sauce, 3% brine, Soju (Korean distilled liquor), thick soy sauce, grape juice and orange juice were higher than those of standard CL (2.94~5.84 g/100 mL). ABS-CL was believed to have a wide use range due to its low sourness while different applications of PBS-CL in food are expected due to its mild astringent taste and strong savory taste despite its strong bitter taste as estimated by sensory evaluation.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.21 no.4
• /
• pp.27-36
• /
• 2015

Purpose: Of late, the focus of service design is moving toward emphasizing customer satisfaction and taking users' experience more seriously. In addition to the change in perspective in service design, scholars in this area are paying more attention to service design methodology and process, as well as its theory and real-world case studies. In the case of medical space, there have been few studies in attempting to apply service design methods useful for deriving user-focused results. The author of this paper believes, however, case study-oriented approaches are more needed in this area rather than ones focusing on theoretical aspects. The author hopes thereby to expand the horizon to practical application of spatial design beyond service design methodology. Methods: In order to incorporate the strengths of service design methodology that can reflect a variety of user opinions, this study will introduce diverse tools in the framework of double diamond process. In addition, it will present field cases that successfully brought about best results in medical space design. It will end with summarizing the ideal process of medical space design which is reasonable and comprehensive. Results: Medical service encompasses preventive medicine as well as treatment of existing medical conditions. A study in establishing the platform of medical service design consists of a wide range of trend research, followed by the summary of two-matrix design classification based on results of the trend research. The draft of design process is divided into five stages composed of basic tools for establishing spatial flow lines created by matching service design tools with each stage of space design processes. In all this, most important elements to consider are communication and empathy. When service design is actually applied to space design, one can see that output has reflected the users' needs very well. The service design process for user-oriented medical space can thus be established by interactions on the final outcome and feedback on the results. Implications: One can see that the service design with the hospital at its center produces the result that encompasses the user's needs best. If the user-focused service design process for medical space can be extended to other space designs, the author believes that it would enhance the level of satisfaction for users and minimize trials and errors.

• Journal of agriculture & life science
• /
• v.44 no.1
• /
• pp.25-32
• /
• 2010

This study examined the effect of moisture level at ensiling on fermentation characteristics of barley and rye silage. The moisture levels, 60 (low; LM), 70(medium; MM) and 80% (high; HM), were controled by adding water or pre-wilting. Barley silage had higher pH and latate:acetate ratio in LM than the other treatments, but those of rye in MM were higher. The concentrations of lactate, total FA and acetate in HM were higher than the other treatments, but propionate concentration in LM was higher than HM. Total N concentrations of barley and rye were highest in MM and LM, respectively. The $NH_3-N$ concentration and total N:$NH_3-N$ ratio of barley were higher in HM than those in LM and MM. With increasing moisture content, buffering capacity of barley and rye silages increased, whereas decreased by increase of pH. There was a negative correlation between moisture content vs. pH of barley and rye silages. However, moisture content vs. the concentrations of total VFA and $NH_3-N$ and the ratio of total N:$NH_3-N$ had a positive correlation. Tn conclusion, the ideal moisture content of barley and rye for silage was 70-80%, but silage quality could be rapidly decreased by pre-wilting to 60% moisture content.

• Korean Journal of Plant Resources
• /
• v.31 no.4
• /
• pp.330-341
• /
• 2018

This study was performed to investigate and measure the antimicrobial activity of evergreen woody species extracts on Trichophyton mentagrophytes. To do this, leaves and stems were collected from Wando and Jeju islands, and were used for the extraction with different solvents (i.e., distilled water, 80% ethanol, and 100% methanol), and at different ultrasonic extracting times (i.e., 15, 30, and 45 minutes). The experiment was conducted by using the agar diffusion method. The clear zone was measured after incubating the paper disc containing the plant extract in a bacterial culture medium. The controls were synthetic antimicrobials, methylparaben and phenoxyethanol, at concentrations of 0.4, 1, 2, and 4 mg/disc. Altogether, extracts of 56 out of 64 species used in this study had inhibitory activity, which confirmed their antimicrobial activity against Athlete's foot. Among them, the crude ethanolic extract of Elaeocarpus sylvestris in 45 min showed a zone of inhibition < 20.2 mm, while the clear zone of Actinodaphne lancifolia ethanolic extraction for 30 min was 23.5 mm. Also, Quercus acuta, Dendropanax morbiferus and Daphne odora showed clear zones of 28.0 mm (45 minutes ethanolic extraction), 20.5 mm (45 minutes crude methanolic extraction) and 19.7 mm (45 minutes methanolic extraction), respectively. Thus, these results confirm that the extracts of evergreen woody species have therapeutic potential against Athlete's foot, and suggest that in order to extract adequate amounts of antimicrobial substance from the plant sources, ideal extraction condition has to be considered.

• The Korea Journal of Herbology
• /
• v.29 no.1
• /
• pp.45-52
• /
• 2014

Objectives : The aim of this study was to investigate the effects water extract of fermented new korean medicinal mixture, combinations of Mori Folium, Adenophorae Radix, Phllostachyos Folium and Citri Pericarpium (F-MAPC), on adipocyte differentiation, adipogenesis and glucose uptake using undiffernentiated 3T3-L1 adipocytes and L6 myoblasts. Methods : Each herb and those mixture were respectively fermented and then extracted with water. We carried on MTT assay for check-up on cell toxicity, Oil Red O staining for determination of cell differentiation and intracelluar adipogenesis. Western blot analysis for measurement of pAMPK and pACC, $C/EBP{\alpha}$, $PPAR{\gamma}$ and Glut-4 protein expressions were performed. Results : F-MAPC showed significant inhibitory activity on adipocyte differentiation in 3T3-L1 preadipocytes without affecting cell toxicity as assessed by measuring fat accumulation, and this effect was 2 fold higher in 0.2 mg/ml F-MAPC than that of the same dose of each fermented herbal extract alone. In addition, these effects were associated with modulation of adipogenic transcription factors, such as $C/EBP{\alpha}$, $PPAR{\gamma}$, as well as stimulated phosphorylations of AMPK and ACC. Translocation of Glut-4 was significantly increased by 10.2% in L6 cells treated with 0.2 mg/ml F-MAPC compared with that of control. Conclusions : These results demonstrate that F-MAPC may be an ideal candidate for therapy of obesity and diabetes by disturbing the differentiation into adipocytes, as well as the inducement of intramuscular glucose uptake from blood.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.33 no.3
• /
• pp.281-286
• /
• 1988

These studies were conducted to find out the polishing methods that improve yield and quality of the polished barley. Four varieties of hulled barley, Dongbori 1. Bunong, Kangbori and Suwon 182 which were produced in Suwon, Korea in 1979, were subjected to this experiment. The polishing machine, manufactured by Satake Co, was used as test mill. Increasing the roller speed of polishing machine causes more polished barley in a unit period. The speed influenced more in length than thickness or width of grain. Therefore the shape of grain became bold type as the speed increased. The optimum roller speed was 1,300rpm in ideal shape of polished barley. The lowest hardness was observed in the husk layer and the hardness was found in the decreasing order of the aleurone, testa, peri carp and the endosperm layer. The thickness of bran layer, weight of 1,000 kernel and hardness of polished barley were greatly different according to barley varieties. Also the length, thickness, width and the ratio of length to width of barley grain were significantly different in barley varieties. The ratio of length to width of the polished barley was 1.59 in Suwon 182, 1.53 in Bunong, 1.51 in Kangbori and 1.26 in Dongbori 1.

• Implantology
• /
• v.18 no.2
• /
• pp.120-138
• /
• 2014

Purpose: The purpose of this study was to review the outcomes of a series of studies on tissue regeneration conducted in multiple institutions including the Department of Periodontology, College of Dentistry, Yonsei University. Materials and Methods: Studies were performed divided into the following three subjects; 1) Development of three-dimensional nano-hydroxyapatite (n-HA) scaffold for facilitating drug release and cell adhesion. 2) Synergistic effects of bone marrow-derived mesenchymal stem cells (BMMSC) application simultaneously with platelet-rich plasma (PRP) on HA scaffolds. 3) The efficacy of silk scaffolds coated with n-HA. Also, all results were analyzed by subjects. Results: Hollow hydroxyapatite spherical granules were found to be a useful tool for the drug release and avidin-biotin binding system for cell attachment. Also, BMMSC simultaneously with PRP applied in an animal bone defect model was seen to be more synergistic than in the control group. But, the efficacy of periodontal ligament cells and dental pulp cells with silk scaffolds could not be confirmed in the initial phase of bone healing. Conclusion: The ideal combination of three elements of tissue engineering-scaffolds, cells and signaling molecules could be substantiated due to further investigations with the potentials and limitations of the suggested list of studies.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.62 no.1
• /
• pp.1-8
• /
• 2017

We investigated the effect of silicate coating of rice seeds on bakanae disease incidence and the quality of seedlings raised in seedling boxes and transplanted into pots. The silicate-coated rice seed (SCS) was prepared as follows. Naturally infested rice seeds not previously subjected to any fungicidal treatment were dressed with a mixture of 25% silicic acid at pH 11 and 300-mesh zeolite powder at a ratio of 50 g dry seed - 9 mL silicic acid - 25 g zeolite powder. The following nursery conditions were provided : Early sowing, dense seeding in a glass house with mulching overnight and no artificial heating, which were the ideal conditions for determining the effect on the seed. The nursery plants were evaluated for Gibberella. fujikuroi infection or to determine the recovery to normal growth of infected nursery plants in the Wagner pot. Seedlings emerged 2-3 days earlier for the SCS than they did for the non-SCS control, while damping-off and bakanae disease incidence were remarkably reduced. Specifically, bakanae disease incidence in the SCS was limited to only 7.8% for 80 days after sowing, as compared to 91.6% of the non-SCS control. For the 45-days-old SCS nursery seedlings, the fresh weight was increased by 11% and was two times heavier, with only mild damage compared to that observed for non-SCS. Even after transplanting, SCS treatment contributed to a lower incidence of further infections and possibly to recovery of the seedlings to normal growth as compared to that observed in symptomatic plants in the pot. The active pathogenic macro-conidia and micro-conidia were considerably lower in the soil, root, and seedling sheath base of the SCS. In particular, the underdeveloped macro-conidia with straight oblong shape without intact septum were isolated in the SCS ; this phenotype is likely to be at a comparative etiological disadvantage when compared to that of typical active macro-conidia, which are slightly sickle-shaped with 3-7 intact septa. A active intact conidia with high inoculum potential were rarely observed in the tissue of the seedlings treated only in the SCS. We propose that promising result was likely achieved via inhibition of the development of intact pathogenic conidia, in concert with the aerobic, acidic conditions induced by the physiochemical characteristics associated with the air porosity of zeolite, alkalinity of silicate and the seed husk as a carbon source. In addition, the resistance of the healthy plants to pathogenic conidia was also important factor.