• ETRI Journal
• /
• 제30권2호
• /
• pp.275-281
• /
• 2008

A 40 Gb/s clock and data recovery (CDR) module for a fiber-optic receiver with improved phase-locked loop (PLL) circuits has been successfully implemented. The PLL of the CDR module employs an improved D-type flip-flop frequency acquisition circuit, which helps to stabilize the CDR performance, to obtain faster frequency acquisition, and to reduce the time of recovering the lock state in the event of losing the lock state. The measured RMS jitter of the clock signal recovered from 40 Gb/s pseudo-random binary sequence ($2^{31}-1$) data by the improved PLL clock recovery module is 210 fs. The CDR module also integrates a 40 Gb/s D-FF decision circuit, demonstrating that it can produce clean retimed data using the recovered clock.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2003년도 종합학술발표회 논문집 Vol.13 No.1
• /
• pp.136-139
• /
• 2003

A clock recovery circuit for a 40 Gb/s optical receiver has been designed and implemented. The clock recovery circuit consists of signal amplifiers, a nonlinear circuit with diodes, and a bandpass filter Before implementing the 40 Gb/s clock recovery circuit, a 10 Gb/s clock recovery circuit has been successfully implemented and tested. With the 40 Gb/s clock recovery circuit, when a 40 Gb/s NRZ signal of -10 dBm was applied to the input of the circuit, the 40 GHz clock was recovered with the -20 dBm output power after passing through the nonlinear circuit. The output signal from the nonlinear circuit passes through a narrow-band filter, and then amplified. The implemented clock recovery circuit is planned to be used for the input of a phase locked loop to further stabilize the recovered clock signal and to reduce the clock jitter.

• 전기학회논문지
• /
• 제61권11호
• /
• pp.1695-1699
• /
• 2012

This paper is proposed all digital wide-range clock and data recovery circuit. The Proposed clock data recovery circuit is possible input data rate which is suggested is wide-range that extends from 100Mb/s to 3Gb/s and used an phase error detector which can use a way of over-sampling a data by using a 1/2-rate multi-phase clock and phase rotator which is regular size per $2{\pi}$/16 and can make a phase rotation. So it could make the phase rotating in range of input data rate. Also all circuit is designed as a digital which has a specificity against a noise. This circuit is designed to 0.13um CMOS process and verified simulation to spectre tool.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제4권4호
• /
• pp.275-279
• /
• 2004

A new burst mode clock and data recovery circuit is realized that improves the previousldy-known gated-oscilletor technique with half rate clock recovery, The circuit was fabricated with 0.25um CMOS technology, and its functions were confirmed up to 1 Gbps.

• 대한임베디드공학회논문지
• /
• 제12권4호
• /
• pp.239-246
• /
• 2017

Time synchronization between distributed embedded systems in the Real Time Locating System (RTLS) based on Time Difference of Arrival (TDOA) is one of the most important factors to consider in system design. Clock jitter error between each system causes many difficulties in maintaining such a time synchronization. In this paper, we implemented a system to synchronize clocks between FPGA based distributed embedded systems using the recovery clock of CDR (clock data recovery) used in high speed serial communication to solve the clock jitter error problem. It is experimentally confirmed that the cumulative time error that occurs when the synchronization is not performed through the synchronization logic using the CDR recovery clock can be completely eliminated.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2005년도 종합학술발표회 논문집 Vol.15 No.1
• /
• pp.191-196
• /
• 2005

A low-cost, high-performance 40 Gb/s clock recovery module using a phase-locked loop(PLL) for a 40 Gb/s optical receiver has been designed and implemented. It consists of a clock recovery circuit, a RF mixer and frequency discriminator for phase/frequency detection, a DR-VCO, a phase shifter, and a hold circuit. The recovered 40 GHz clock is synchronized with a stable 10 GHz DR-VCO. The clock stability and jitter characteristics of the implemented PLL-based clock recovery module has shown to significantly improve the performance of the conventional open-loop type clock recovery module with DR filter. The measured peak-to-peak RMS jitter is about 230 fs. When input signal is dropped, the 40 GHz clock is generated continuously by hold circuit. The implemented clock recovery module can be used as a low-cost and high-performance receiver module for 40 Gb/s commercial optical network.

• ETRI Journal
• /
• 제30권2호
• /
• pp.268-274
• /
• 2008

This paper proposes an open-loop clock recovery circuit (CRC) using two high-Q dielectric resonator (DR) filters for 39.8 Gb/s and 42.8 Gb/s dual-mode operation. The DR filters are fabricated to obtain high Q-values of approximately 950 at the 40 GHz band and to suppress spurious resonant modes up to 45 GHz. The CRC is implemented in a compact module by integrating the DR filters with other circuits in the CRC. The peak-to-peak and RMS jitter values of the clock signals recovered from 39.8 Gb/s and 42.8 Gb/s pseudo-random binary sequence (PRBS) data with a word length of $2^{31}-1$ are less than 2.0 ps and 0.3 ps, respectively. The peak-to-peak amplitudes of the recovered clocks are quite stable and within the range of 2.5 V to 2.7 V, even when the input data signals vary from 150 mV to 500 mV. Error-free operation of the 40 Gb/s-class optical receiver with the dual-mode CRC is confirmed at both 39.8 Gb/s and 42.8 Gb/s data rates.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제16권3호
• /
• pp.287-292
• /
• 2016

A multiphase clock and data recovery (CDR) circuit having a novel rotational bang-bang phase detector (RBBPD) is demonstrated. The proposed 1/4-rate RBBPD decides the locking point using a single clock phase among sequentially rotating 4 clock phases. With this, our RBBPD has significantly reduced power consumption and chip area. A prototype 10-Gb/s 1/4-rate CDR with RBBPD is successfully realized in 65-nm CMOS technology. The CDR consumes 5.5 mW from 1-V supply and the clock signal recovered from $2^{31}-1$ PRBS input data has 0.011-UI rms jitter.

• 전자공학회논문지SC
• /
• 제46권1호
• /
• pp.82-86
• /
• 2009

본 논문은 시스템의 클록을 이용하여 클록 및 데이터를 복원하는 회로를 설계하였다. 설계된 회로에는 시스템의 클록을 만들어주는 PLL부분과 클록을 받아 데이터를 복원하는 데이터 복원회로부분으로 구성되어 있다. 데이터 복원회로에서는 1/4-rate 위상검출기를 이용하여 데이터보다 시스템의 클록주파수를 낮추어 설계하여 PLL의 부담을 줄일 수 있었고 데이터 picking 방식으로 설계하여 적은 지터특성을 보였다. 설계된 클록 데이터 복원회로는 $0.18{\mu}m$ 1P6M CMOS공정으로 설계되었고 칩 면적은 $1{\times}1mm^2$이다.

• ETRI Journal
• /
• 제34권1호
• /
• pp.35-43
• /
• 2012

This paper presents a delay-locked-loop-based clock and data recovery (CDR) circuit design with a nB(n+2)B data formatting scheme for a high-speed serial display interface. The nB(n+2)B data is formatted by inserting a '01' clock information pattern in every piece of N-bit data. The proposed CDR recovers clock and data in 1:10 demultiplexed form without an external reference clock. To validate the feasibility of the scheme, a 1.7-Gbps CDR based on the proposed scheme is designed, simulated, and fabricated. Input data patterns were formatted as 10B12B for a high-performance display interface. The proposed CDR consumes approximately 8 mA under a 3.3-V power supply using a 0.35-${\mu}m$ CMOS process and the measured peak-to-peak jitter of the recovered clock is 44 ps.