• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.610-614
• /
• 2004

Recently, an active-clamp, full-bridge boost converter has been actively studied for high-power applications such as power factor correction and battery discharger. However, DC and AC modeling for this converter has not conquered. In this paper, a DC and small-signal AC modeling for the active-clamp, full-bridge boost converter is described. Based on the operation principle, the ac part of the converter can be replaced by a do counterpart. Then, a conceptual equivalent circuit is derived by rearranging the switches. The equivalent circuit for this converter consists of CCM (Continuous conduction mode) boost and DCM (Discontinuous conduction mode) buck converter. The analyses for the equivalent CCM boost and DCM buck converter are done using the model of PWM switch. The theoretical modeling results are confirmed through experiment or SIMPLIS simulation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.169-176
• /
• 2005

In this paper, a DC and small-signal AC modeling for the active-clamp, ful1-bridge boost converter is described. Based on the operation principle, the ac part of the converter can be replaced by a dc counterpart. Then, a conceptual equivalent circuit is derived by rearranging the switches. The equivalent circuit for this converter consists of CCM(Continuous conduction mode) boost and DCM(Discontinuous conduction mode) buck converter. The analyses for the equivalent CCM boost and DCM buck converter are done using the model of PWM switch. The theoretical modeling results are confirmed through experiment or SIMPLIS simulation.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.400-403
• /
• 2000

This paper deals with the active clamp ZVS flyback converter for semiconductor plasma etching system. The proposed converter has the characteristics of the good power facter low switching noise and efficiency improvement. The characteristics are verified through simulation results. Furthermore the ringing effect due to output capacitance of the main switch can be eliminated by use of active clamp circuit.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05b
• /
• pp.966-969
• /
• 2011

본 논문에서는 자동차용 Battery Post Terminal Clamp의 응력감소를 위한 설계에 있어, ANSYS Workbench 11.0을 이용한 유한요소 구조해석을 하였다. 체결 시 볼트 조임에 따라 가해지는 힘에 따른 응력집중 및 변형을 고려하였고, Battery Post Terminal Clamp에 응력이 집중되어 소성변형이 예상되는 부분에 대한 형상을 변형 하였을 때, 발생 응력이 극한 인장 강도 이하로 감소됨을 확인하였다.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.386-389
• /
• 2002

This paper proposes the boost input type active clamp forward ZVS(zero voltage switching) DC-DC converter which can provide high efficiency and improved EMI characteristics. Moreover, it has active clamp circuit for reducing the voltage stress and zero voltage switching technique for minimizing switching loss. The detailed operation principles and the simulation results are presented.

• Journal of Electrical Engineering and information Science
• /
• v.3 no.3
• /
• pp.366-372
• /
• 1998

A high efficiency interleaved active clamp forward converter with self driven synchronous rectifiers for a modular power processor is presented. To simplify the gate drive circuits, N-P MOSFETs coupled active clamp method is used. An efficiency about 90% for the load range of 50-100% is achieved. The details of design for the power stage and current mode control circuit are provided, and also some experimental results are given.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1235-1238
• /
• 2004

This paper presents the large-signal transient analysis of a self-driven active-clamp forward converter, eliminating the extra drive circuit for the active clamp switch. The operation principle of the converter was presented and experiential results were used to verify the analyzed results. A 50-W prototype converter built and tested it. From the tested results, input transient response and load transient response of the converter were established.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.6
• /
• pp.543-550
• /
• 2006

A three-level sustain circuit with six-switches for an ac plasma display panel (AC-PDP) drive is proposed. The proposed circuit features half the voltage stresses of sustain switches and clamp diodes and significantly reduced power losses compared with those of the conventional ones. This circuit, realizable with reduced cost of the semiconductor devices, gives a significant improvement in the power efficiency, essential for the design of a drive circuit for the AC-PDP. A comparative analysis and experimental results we presented to show the validity of the proposed sustainer circuit.

• Journal of IKEEE
• /
• v.17 no.2
• /
• pp.208-213
• /
• 2013

In this paper, we proposed the novel SCR-based ESD protection circuit with high holding voltage for power clamp. In order to increase the holding voltage, the floating p+ and n+ to n-well and p-well, respectively, in the conventional SCR. The resulting increase of the holding voltage of the our proposed ESD circuit enables the high latch-up immunity. The electrical characteristics including ESD robustness of the proposed ESD circuit have been simulated using Synopsys TCAD simulator. According to the simulation result, the proposed device has higher holding voltage of 4.98 V than that of the conventional SCR protection circuit. Moreover, it is confirmed that the device could have the holding voltage of maximum 13.26 V with the size variation of floated diffusion area.

• Journal of Power Electronics
• /
• v.4 no.2
• /
• pp.87-95
• /
• 2004

A new fast-response high-current clamp DC-DC converter circuit design is presented that will meet the requirements and features of the new generation of microprocessors and digital systems. The clamp in the proposed converter amplifies the current in case of severe load changes and is able to produce high slew rate of output current and capability to keep constant the output voltage. This proposed high-current clamp technique is theoretically loss less, low cost and easy to implement with simple control scheme. This is modified from a basic buck topology by replacing the output inductor with two magnetically coupled inductors. Inductors are difference in inductance, one has large inductance and other has small inductance. The inductor with small inductance will take over the output inductor during fast load transient. It speedup the output current slew rate and reduce the output voltage drop in the case of heavy burden load changes.