• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 추계 학술논문 발표대회
• /
• pp.188-189
• /
• 2013

The purpose of this research is to comprehend experimentally the characteristic of human dynamic load and provide the result as basic data to suggest a valid impact-resistance evaluation method. Human motions exerting dynamic load are classified to 3 types. Selecting 3 ranks of motion strength, 3 ranks of load plane stiffness (A:20kN/cm, B:4.7kN/cm, C:2.2kN/cm), and 30 male grownup inspectors in their twenties, load was measured when they applied force on load plane. Result of this research is as follows: (1) Human dynamic load has different nature from object collision in the highest load ratio depending on the load plane stiffness and action time (2) The highest load ratio for each motion was 10.06 for kicking, 4.44 for hitting with shoulder, and 5.58 for fist blow.

• 조명전기설비학회논문지
• /
• 제15권2호
• /
• pp.31-37
• /
• 2001

본 논문은 기존의 전원분할 기능만을 하는 전해 커패시터 대신에 ZVS, ZCS와 전원분할 및 공진 기능을 동시에 가지며, 분할비를 이용하면 서로 다른 출력특성을 얻을 수 있는 ZVS-HB형 DC-DC 컨버터를 제안하고 있다. 회로의 해석은 전원분할 커패시터의 분할비에 따른 대부분의 특성들을 무차원화 파라미터를 적용하여 범용성 있게 기술하고 있다. 또, Power-MOSFET를 적용한 실험에서 얻은 실험치와 특성해석에서 얻은 이론치를 비교 하여 특성해석의 정당성을 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1177-1179
• /
• 2005

This paper presents the characteristic analysis of slotless tubular type Linear DC Motor with Permanent Magnet excitation as variation of magnetic pole-pitch ratio. The stator armature winding of this motor is designed to wind at inner stator around the mover mounted with permanent magnet. First the practical model of this motor is made and its parameter is measured, after this simulation is carried out. Comparing the simulation results as variation of pole-pitch ratio, it can be seen that the reaching ability makes it useful in applications requiring a small, direct-drive actuator, which is required to extend into a specially constrained environment.

• 한국산업융합학회 논문집
• /
• 제17권1호
• /
• pp.7-14
• /
• 2014

In this study, characteristic of elastic paving materials in bicycle road using polyurethane were studied experimentally. As a results, following their good result was obtained. Bicycle road packaging materials are flexural strength g test, ratio of mass change after freezing and thawing, repulsion elasticity test, water Permeation coefficient test and slip resistance test results showed good performance.

• 대한의용생체공학회:의공학회지
• /
• 제10권3호
• /
• pp.223-228
• /
• 1989

In this paper, the computerized interpretation of the analytical chemical data, especially GC/MS data, was performed for the purpose of prescreening of the target compounds. First, the data from the analytical instrument was analyzed to get the information about the retention time of the ISTD and the time inteval between the records. Second, the identification of the characteristic ion peaks was performed by calculating the ratio of the heights and the relative slope sensitivity of the characteristic mass abundance.

• 대한기계학회논문집
• /
• 제14권6호
• /
• pp.1629-1638
• /
• 1990

Using a 1/10 scale model pump, which is designed and manufactured to simulate two phase performance of reactor coolant pump of Y.G.N

• 한국정밀공학회지
• /
• 제15권1호
• /
• pp.145-151
• /
• 1998

This paper addresses the results of an experimental and analytical research of cylindrical coil spring subjected to dynamic behavior. Transfer functions are presented for both deflection and transmitted force as the output with force as the input. Steady state sinusoidal magnitude ratio and transmittance are plotted along with experimental data. It is shown that dynamic characteristic of cylindrical coil spring must be used to enhance the reability of vibration system dynamic behavior analysis in actuating over some frequency.

• Tribology and Lubricants
• /
• 제17권2호
• /
• pp.116-123
• /
• 2001

A theoretical analysis has been undertaken to show the influence of bearing geometry on the steady state characteristics of air lubricated spherical tilting pad bearings. The geometry variations considered are the number of pads, the eccentricity ratio, the direction of load, and the preloading. Dynamic characteristic equations are derived with pad assembly method.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제12권1호
• /
• pp.25-32
• /
• 2008

A pin fin is optimized based on the increasing rate of heat loss by using a two-dimensional analytic method. The optimum heat loss, corresponding optimum thermal resistance and fin length are presented as a function of the fin base thickness, convection characteristic numbers ratio, fin outer radius and ambient convection characteristic number. One of the results shows that both the optimum heat loss and fin length decrease linearly whereas the optimum thermal resistance increases very slightly with increase of the fin base thickness.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 춘계 학술논문 발표대회
• /
• pp.273-274
• /
• 2018

When IGCC Slag(CGS) aggregate was used as PHC-Pile, the moldability was lowered as the mixing ratio increased. concrete mix design. Also the mix characteristics increased the use of AD depending on the usage rate, however, require detailed consideration.