• KEPCO Journal on Electric Power and Energy
• /
• v.1 no.1
• /
• pp.135-140
• /
• 2015

Decomposition of carbon dioxide is studied using $Ar/CO_2$ mixture inductively coupled plasmas (ICP). Argon gas was added to generate plasma which has high electron density. To measure decomposition rate of $CO_2$, optical emission actinometry is used. Changing input power, pressure and mixture ratio, the plasma parameters and the spectrum intensity were measured using single Langmuir probe and spectroscope. The source characteristic of Carbon dioxide ICP observed from the obtained plasma parameters. The decomposition rate is evolved depending on the reaction and discharge mode. This result is analyzed with both the measurement of the plasma parameters and the dissociation mechanism of $CO_2$.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.8
• /
• pp.52-58
• /
• 2008

Ths paper describes the Dual-band switch which was proposed new structure that could improved the specification of broadband and designed by the optimized structure through simulation. The Dual-band switch with 2.4[GHz]/5.8[GHz] that can apply to 802.11a/b/g system that is commercialized present was studied to get a new structure with higher power, high isolation. The transmitter of switch was designed to operate a parallel switching element with stack structure of two FET. The receiver designed to have asymmetry structure that insert series FET in addition to basic serial/parallel FET. SPDT(Single Pole Double Throw) Tx/Rx FET switch is a device that can do switching from a port of input to two port of output. The fabricated SPDT switch has the characteristic of insertion loss of a below -3[dB] form DC to 6[GHz] and the isolation of a below -30D[dB](Rx mode).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.1
• /
• pp.23-28
• /
• 1999

Rectangular waveguide slot antenna which has simple structure, high efficiency, high trust and small size, is extending in a field of application such as many Radar and Microwave communication. A slot cut into a wall of waveguide is propagated electromagnetic wave to free space it interrtupts the flow of current inner conductor of waveguide. Therefore incident of slot, cutdepth, width, length, i.e. are important parameter of characteristic change of the slot antenna. Result from difficulty of theoretical analysis about slot frequently experimental measured data useful design and manufacture have been accomplished. In this paper, we find the suitable method of analysis that compare two analysis results with measured result of established literature - admittance of slot be solved by propagated power from electric field distribution of slot and mode current computation and accomplishment of computable chart which hasresonant length and cutdepth, incident of slot, i.e. and use the HFSS which applyed finite-element method obtain equal slot analyed method.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1621-1622
• /
• 2006

This paper presents the effect of driving waveform for piezoelectric bend mode inkjet printhead with optimized mechanical design. Experimental and theoretical studies on the applied driving waveform versus jetting characteristic s were performed. The inkjet head has been designed to maximize the droplet velocity, minimize voltage response of the actuator and optimize the firing frequency to eject ink droplet. The head design was carried out by using mechanical simulation. The printhead has been fabricated with Si(100) and SOI wafers by MEMS process and silicon direct bonding method. To investigate how performance of the piezoelectric ceramic actuator influences on droplet diameter and droplet velocity, the method of stroboscopy was used. Also we observed the movement characteristics of PZT actuator with LDV(Laser Doppler Vibrometer) system, oscilloscope and dynamic signal analyzer. Missing nozzles caused by bubbles in chamber were monitored by their resonance frequency. Using the water based ink of viscosity of 4.8 cps and surface tension of 0.025N/m, it is possible to eject stable droplets up to 20kHz, 4.4m/s and above 8pL at the different applied driving waveforms.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.17 no.1
• /
• pp.36-41
• /
• 2014

A floating offshore structure has high tendency to occur the buckling when compressive, bending and shear loads applied. When the buckling is occurred, in-plane stiffness of structure is remarkably decreased. And it has a harmful effect on the local structural strength as well as global structural strength. In the present study, it has been investigated the ultimate strength of tubular members which is located between a floater and a damping plate of the floating pendulum wave energy converter. Nonlinear finite element method is conducted using the initial imperfection according to 1st buckling mode which is obtained from the elastic buckling analysis. It is also noted the ultimate bending strength characteristic varying with a diameter, thickness and stiffeners of the tubular member.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.10
• /
• pp.2039-2044
• /
• 2009

The PSK carrier signal recovery circuit using multi-layer coupled line was analyzed and designed. The fabricated carrier recovery 6 port element with multi-layer coupled line structure gets the simple architecture. It is possible to implement the carrier signal recovery circuit of the same structure with the multi-layer six port phase correlator of the direct receiver front-end. Based on the analysis of RML carrier recovery circuit using the multi-layer coupled line 6-port phase correlator, the multi-layer coupled line carrier signal recovery structure for multi-mode coherent demodulation was proposed. The fabricated multi-layer coupled line carrier signal recovery circuit for quadrature phase shift-keying shows a good carrier signal characteristic with a constant phase and phase error below ${\pm}3o$.

• Journal of the Korean Institute of Gas
• /
• v.7 no.2 s.19
• /
• pp.48-53
• /
• 2003

This study is to look at the effect for deformation of carbon steel for high-presure pipe, on the AE signals produced by tensile test. Acoustic emission(AE) has been widely used in various fields because of its extreme sensitivity, dynamic detection ability and location of growing defects. We investigated a relationship failure mode and AE signals by tensile test, From the tensile test, we could divide into four ranges of the failure modes of elastic range, yield range, plastic range before $\sigma$u, plastic range after $\sigma$u. And failure behaviors of elastic range, yield range, plastic range before $\sigma$u, plastic range after $\sigma$u could be evaluated in tensile test by AE counts, accumulation counts and time frequency analysis. It is expected to be basic data that can protect a risk according to tensile test and bending of pipe material for pressure vessel, as a real time test of AE.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.392-395
• /
• 2003

For the purpose of digital x-ray imaging, many materials such as $PbI_2$, $HgI_2$, TlBr, CdTe and CdZnTe have been under development for servaral years as direct converter layer. $Hgl_2$ film detector have recently been shown as one of the most promising semiconductor materials to be used as direct converters in x-ray digital radiography. This paper, the $HgI_2$ films are deposited on conductive-coated glass by screen printing, in which $HgI_2$ powder is embedded in a binder and solvent, and the slurry is used to coat the conductive-coated glass. We investigated electrical characteristic of the fabricated $HgI_2$ films. The x-ray response to radiological x-ray generator of 70Kvp using the current integration mode will be reported for screen printing films. These results indicate that $HgI_2$ detectors have high potential as new digital x-ray imaging devices for radiography.

• Journal of Korean Society of Rural Planning
• /
• v.22 no.2
• /
• pp.141-152
• /
• 2016

The role of rural towns as a leisure space has recently been increasing with changes in the consumption trends in domestic tourism. Based on the tourists visiting the town of Sunheul-ri, Jocheon-eup, a rural Village in Jeju Island, this study categorized the market according to the images formed by the tourists of rural towns, and analyzed the preferred mode of participation in rural field activities for each category. We analyzed the characteristic factors of the images of rural tourism formed by the tourists, extracted three factors for cluster analysis, and then formed three groups: "Group of Rural Experience Activity" "Group of Rural Environment and Service" and "Group of Rest in the Rural" After analyzing the preferred activity in each image-category group, we found no significant differences among the groups in ordinary activities such as viewing the scenery, experiencing and learning about the natural environment, and culinary experiences. However, there were significant differences among the groups regarding participation in experiential tour programs with the purpose of active tourism. The "Group of Rural Experience Activity" sought to actively participate in various activity programs, whereas the "Group of Rest in the Rural" comparatively had a weaker preference for such active programs. We thus learnt that tourists' preferred activities are different according to the types of images formed by the tourists visiting rural towns. Therefore, to strengthen the competitive advantage of the rural tourist destinations of Jeju Island, it is necessary to provide various activity programs that are appropriate for the rural regions of Jeju and to accord with the expectations associated with each market segment category by positioning the programs according to the characteristics of the images held by the tourists.

• Progress in Superconductivity
• /
• v.14 no.1
• /
• pp.1-10
• /
• 2012

We fabricated a closed coils by using resistive-joint method and the joint resistance of the coils were estimated by field decay technique in liquid nitrogen. We used the Runge-kutta method for the numerical analysis to calculate the decay properties. The closed coil was wound by $(Bi,Pb)_2Sr_2Ca_2Cu_3O_x$/Ag tape. Both ends the tape were overlapped and soldered to each other. The current was induced in a closed coils by external magnetic flux density. Its decay characteristic was observed by means of measuring the magnetic flux density generated by induced current at the center of the closed coil with hall sensor. The joint resistance was calculated as the ratio of the inductance of the loop to the time constants. The joint resistances were evaluated as a function of critical current of loop, contact length, sweep time, and external magnetic flux density in a contact length of 7 cm. It was observed that joint resistance was dependent on contact length of a closed coil, but independent of critical current, sweep time, and external magnetic flux density. The joint resistance was measured to be higher for a standard four-probe method, compared with that for the field decay technique. This implies that noise of measurement in a standard four-probe method is larger than that of field decay technique. It was estimated that joint resistance was $8.0{\times}10^{-9}{\Omega}$ to $11.4{\times}10^{-9}{\Omega}$ for coils of contact length for 7 cm. It was found that 40Pb/60Sn solder are unsuitable for persistent mode.