• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.4B
• /
• pp.637-646
• /
• 2010

For 40 Gb/s data transmission through electrical backplane trace up to 40 inch length on four layer fire-resistant (FR-4), we have designed the 40 Gb/s backplane channel model consisting of four channel 10 Gb/s. Simulation results show an enhancement of backplane channel characteristics excellent more than requirements specified in IEEE P802.3ba at 10 Gb/s. This paper provides a review of the structures and algorithms used in receive and adaptive equalization for 40 Gb/s backplane Ethernet. The use of this backplane channel model could achieves better receive equalizer at great data rate than 10 Gb/s.

• Korean Journal of Optics and Photonics
• /
• v.1 no.1
• /
• pp.1-6
• /
• 1990

We studied two-photon-resonant three-photon ionization processes via 4D[channel #1] and 5S(channel #2] intermediate state of Na atom in a quartz ionization cell. For each channel. the bandwidth of ionization spectrum increased linearly with laser intensity and the ionization signal followed J3 dependence at low intensity. Compared with channel # 1 . ionization signal of channel #2 was enhanced by a factor of 20 - 25. The measured AC Stark shift factor of 3S - 4I) transition was $174\pm60MHz/MW/textrm{cm}^2$..

• International Journal of Computer Science & Network Security
• /
• v.23 no.1
• /
• pp.96-102
• /
• 2023

In this paper, we proposed Channel Transfer Function estimation based on Delay and Doppler Profile for underwater acoustic OFDM communication system. It improved the estimation accuracy of the channel transfer function by linear time interpolation the change of Scattered Pilot (SP) insertion frequency in the time direction and the time by Delay and Doppler profile that analyzes the multipath situation of the channel investigated the performance of interpolation by simulation and report it. Previous works is inserted SP every 4 OFDM. It was effective under the environment without multipath, but it has observed that the effect of CTF compensation has been lowered in multipath channel condition. In addition to be better when inserted SP every 2 OFDM. But the amount of sending data will be decrease. Therefore, we conducted research to improve 4 OFDM with new interpolator. A computer simulation was performed as a comparison of SP inserted every 4 OFDM, SP inserted every 2 OFDM, and 4 OFDM with new interpolator. the performance of the proposed system is overwhelmingly improved, and the performance is slightly improved even 64 QAM.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.5
• /
• pp.1191-1197
• /
• 1994

The purpose of this study is to examine morphometric characteristics in a channel bend reach. The new shape factor is suggested that channel deformation rate of cross section (${\Delta}A_s$) showed the variation of concentrated location of force due to the current and the variation of erosional section in alluvial channel. In the downstream direction the meaning of decreasing "${\Delta}A_s$" is the stability of channel bed. This study was analyzed morphological characteristics of cross section-width of channel ($W_s$), width to the thalweg ($W_{th}$), maximum depth ($D_{th}$)-on the Guem River, and typical cross sections in channel bend were proposed. The channel migration rate (M) for the study river was represented that the zones of curvature ratio (R/W) with 2~4 were larger 12% than other zones.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.2
• /
• pp.181-188
• /
• 2012

In this paper, the measurement data is analyzed and channel parameters are derived through MIMO Channel measurements at 781MHz considering outdoor multi-path environment. 781MHz frequency band currently operates the DTV system. However, it will be allocated new mobile communication frequency band. The channel characteristics at 781MHz seem to be similar existing mobile communication system at 900MHz but a study on channel characteristics of signal transfer process is necessary because there is incomplete study in mobile networks at 781MHz. To avoid interference with Korean DTV broadcasting, we measured channel characteristics in city/suburban areas of Jeju island by channel sounder and $4{\times}4$ antenna of the ETRI(Korea Electronics and Telecommunications Research Institute). Path Loss, Delay Spread, Angular Spread and K-factor were derived based on measured data.

• Korean Chemical Engineering Research
• /
• v.53 no.6
• /
• pp.818-823
• /
• 2015

In this study, FT reaction in a microchannel was simulated using computational fluid dynamics(CFD), and sensitivity analyses conducted to see effects of channel geometry variables, namely, process channel width, height, gap between process channel and cooling channel, and gap between process channels on the channel temperature profile. Microchannel reactor considered in the study is composed of five reaction channels with height and width ranging from 0.5 mm to 5.0 mm. Cooling surfaces is assumed to be in isothermal condition to account for the heat exchange between the surface and process channels. A gas mixture of $H_2$ and CO($H_2/CO$ molar ratio = 2) is used as a reactant and operating conditions are the following: GHSV(gas hourly space velocity) = $10000h^{-1}$, pressure = 20 bar, and temperature = 483 K. From the simulation study, it was confirmed that heat removal in an FT microchannel reactor is affected channel geometry variables. Of the channel geometry variables considered, channel height and width have significant effect on the channel temperature profile. However, gap between cooling surface and process channel, and gap between process channels have little effect. Maximum temperature in the reaction channel was found to be proportional to channel height, and not affected by the width over a particular channel width size. Therefore, microchannels with smaller channel height(about less than 2 mm) and bigger channel width (about more than 4 mm), can be attractive design for better heat removal and higher production.

• International Journal of Internet, Broadcasting and Communication
• /
• v.12 no.4
• /
• pp.18-25
• /
• 2020

In the fifth generation (5G) and beyond 5G (B5G) mobile communication, non-orthogonal multiple access (NOMA) has attracted great attention due to higher spectral efficiency and massive connectivity. We investigate the impacts of the channel estimation errors on the bit-error rate (BER) of NOMA, especially with the single-user decoding (SUD) receiver, which does not perform successive interference cancellation (SIC), in contrast to the conventional SIC NOMA scheme. First, an analytical expression of the BER for SUD NOMA with channel estimation errors is derived. Then, it is demonstrated that the BER performance degrades severely up to the power allocation less than about 20%. Additionally, we show that for the fixed power allocation of 10% in such power allocation range, the signal-to-noise (SNR) loss owing to channel estimation errors is about 5 dB. As a consequence, the channel estimation error should be considered for the design of the SUD NOMA scheme.

• Steel and Composite Structures
• /
• v.3 no.4
• /
• pp.243-260
• /
• 2003

This paper reports on the development of a new composite slab system that uses a large- lipped steel channel and reinforced concrete. The advantages of this new system are that it serves as both a structural unit and an unsupported form and it has a secondary structural barrier function. A concrete pouring test was carried out for the large-lipped steel channel. Full-scale tests were carried out to assess the flexural strength-deformation characteristics and structural mechanics of the composite slab. The barrier mechanics of the steel channel concrete element (referred to as the SC subunit) of the composite slab are examined. The test results indicate that the new composite slab has excellent strength, ductility characteristics, and a structural barrier function in its SC subunit that is highly effective against severe loading.

• 전기의세계
• /
• v.27 no.4
• /
• pp.45-51
• /
• 1978

A new method of realizing the field effect transistor with a sub-.mu. channel width is described. The sub-.mu. channel width is made possible by etching grooves into n$^{+}$ pn$^{[-10]}$ n$^{[-10]}$ structure and using p region at the wall for the channel region of the Metal-Oxide-Semiconductor transistor (MOST), or by diffusing two different types of impurities through the same diffusion mask and using p region at the surface for the channel region of MOST. When the drain voltage is increased at the pn$^{[-10]}$ drainjunction the depletion layer extends into the n$^{[-10]}$ region instead of into p region; this is also the secret of success to realize the sub-.mu. channel width. As the result of the experimental fabrication, a microwave MOST was obtained. The cut-off frequency was calculated to be 15.4 GHz by Linvill's power equation using the measured capacitances and transconductance.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.4
• /
• pp.784-789
• /
• 2007

This paper presents an implementation of a new type of architecture to improve an overflow problem on the network buffer. Each receiver channel of network system stores the message in its own buffer. If some receiver channel receives many messages, buffer overflow problem may occur for the channel. This paper proposes a network controller that implements a receiver channel with shared-memory to save all of the received messages from the every incomming channels. The proposed architecture is applied to ARINC-429, a real-time control network for commercial avionics system. For verifying performance of the architecture, ARINC-429 controller is designed using a SOPC platform, designed by Verilog and targeted to Xilinx Virtex-4 with a built-in PPC405 core.