• KIEE International Transactions on Power Engineering
• /
• v.5A no.2
• /
• pp.152-158
• /
• 2005

This paper describes a reactive optimal power flow incorporating margin enhancement constraints. Margin sensitivity at a steady-state voltage instability point is calculated using invariant space parametric sensitivity, and it can provide valuable information for selection of effective control parameters. However, the weakest buses in neighboring regions have high margin sensitivities within a certain range. Hence, the control determination using only the sensitivity information might cause violation of operational limits of the base operating point, at which the control is applied to enhance voltage stability margin in the direction of parameter increase. This paper applies an interior point method (IPM) to solve the optimal power flow formulation with the margin enhancement constraints, and shunt capacitances are mainly considered as control variables. In addition, nonlinearity of margin enhancement with respect to control of shunt capacitance is considered for speed-up control determination in the numerical example using the IEEE 118-bus test system.

• Journal of Korean Institute of Industrial Engineers
• /
• v.26 no.2
• /
• pp.95-100
• /
• 2000

Presented in this paper is a scheme for constructing ball rolling blends of a non-uniform B-spline surface(NUBS) patches. Ball rolling blending is a popular technique for blending between parametric surfaces. Along the "common edge" of a pair of "base surfaces" to be blended, a sequence of "ball positions" is sampled. The radius of the ball may vary along the line. At each sampling point, a ball center point and a pair of ball contact points are computed by applying a Jacobian inversion method. Using ball contact points, the constructing scheme of blend NUBS patches consists three steps; 1) determination of intermediate control vertices; 2) determination of boundary vectors; 3) determination of B-spline control vertices. The proposed blending scheme has been tested in a Omega CAM system and found to be working satisfactorily.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.11
• /
• pp.1780-1784
• /
• 2006

Cloud point extraction was used to extract mefenamic acid (MF) from human urine, and spectrofluorimetry and spectrophotometry were used to analyze extracted MF. The variables affecting extraction and phase separation, i.e. HCl and Triton X-114 concentration, temperature and time of equilibration, were optimized. Under the experimental conditions used the limit of detection for extraction of 25 mL of sample was 0.006 and 0.045 mg $L^{-1}$, with relative standard deviations of 2.52 and 1.45% (n = 5) for spectrofluorimetric or spectrophotometric methods, respectively. Good recoveries in the range of 95-107% were obtained for spiked samples. The proposed methods were applied to the determination of MF in human urine.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.6
• /
• pp.981-987
• /
• 1997

Modern helicopter rotor blades with non-homogeneous cross section composed of anisotropic material rquire highly sophisticated structural analysis. Variation in cross section geometry makes this task of analysis more complicated. Since rotor blades generally are much longer than their lateral dimensions, one-dimensional models seem feasible, at least from a computational point of view. Therefore determination of the principal coordinate system is very important to remove the structural coupling for one-dimensional beam modelling. In this study, shear center, and principal direction. The method will be verified by comparing the results with confirmed experimental results.

• Journal of the Korean Geophysical Society
• /
• v.8 no.1
• /
• pp.23-33
• /
• 2005

The digital surface model (DSM) is used for several purposes in photogrammetry, remote sensing and laser scanned data such as orthoimage production, contours erivation, extraction of height information. Creation of a surface model from point-clouds (3-D sparse points) that can be derived from stereo imagery and range data (e.g. laser scanned data) can be done with several mathematical interpolation models. In this paper, thin-plate-spline (TPS) is used for digital surface modeling. Determination of suitable weight is an important problem in thin-plate function for a surface. The Voronoi algorithm has been proposed as a method for determination of the weight in thin-plate-spline. In this paper, methods has been tested for different surfaces. The results show that thin-plate-spline can be independent of weight.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.3 no.4
• /
• pp.276-281
• /
• 2008

Because the distribution systems experience frequently the fault by several causes, the identification task of fault location plays very important role in the view point of power supply reliability. The distribution systems are designed as radial structure with three-phase and single-phase branch line to supply the electric power to the widely dispersed loads, and it have a several load taps within each line segment. it makes the accurate fault distance determination difficult. Accordingly in this papers, the existing fault point determination methods are surveyed and analyzed, and then a fault distance determination method for distribution feeder is adopted which can be executed effectively in DAS center. Finally, the adopted method is verified using EMTP simulation.

• Journal of Applied Reliability
• /
• v.14 no.4
• /
• pp.230-235
• /
• 2014

The failure modes of pneumatic directional control valves include leakage, wear of the spool seal, and sticking of the spool. Among them, the main failure mode of the valve is leakage. The leakage is caused by the wear of the spool seal. However, due to the characteristics of the seal material, the leakage rate is fluctuated a lot rather than constantly increased over time. If life analysis is performed using the first time data of leakage failure, predicted life cycles can be different from the real life cycles. This paper predicts life cycles of the pilot pneumatic directional control valve based on the three point moving average which considers the average of the fluctuating leakage rate.

• Journal of Korea Spatial Information System Society
• /
• v.5 no.2 s.10
• /
• pp.83-89
• /
• 2003

In this study, a new coded targets that being suitable for a Mobile Mapping System and method of automated target recognition and coordinates determination of center point was developed, the purpose of a Mobile Mapping System is acquisition and logging data around the road for the camera calibration and the Exterior orientation of system, target installed previously and CCD cameras captured the image, target center point was observed by hands, but using coded target, target recognition and center point observation process will be automated effectively, in addition we keeped up the consistency of photo coordinates observation.

• Imaging Science in Dentistry
• /
• v.50 no.4
• /
• pp.323-330
• /
• 2020

Purpose: The mastoid region is ideal for studying sexual dimorphism due to its anatomical position at the base of the skull. This study aimed to determine sex in the Iranian population based on measurements of the mastoid process using different data mining algorithms. Materials and Methods: This retrospective study was conducted on 190 3-dimensional cone-beam computed tomographic (CBCT) images of 105 women and 85 men between the ages of 18 and 70 years. On each CBCT scan, the following 9 landmarks were measured: the distance between the porion and the mastoidale; the mastoid length, height, and width; the distance between the mastoidale and the mastoid incision; the intermastoid distance (IMD); the distance between the lowest point of the mastoid triangle and the most prominent convex surface of the mastoid (MF); the distance between the most prominent convex mastoid point (IMSLD); and the intersecting angle drawn from the most prominent right and left mastoid point (MMCA). Several predictive models were constructed and their accuracy was compared using cross-validation. Results: The results of the t-test revealed a statistically significant difference between the sexes in all variables except MF and MMCA. The random forest model, with an accuracy of 97.0%, had the best performance in predicting sex. The IMSLD and IMD made the largest contributions to predicting sex, while the MMCA variable had the least significant role. Conclusion: These results show the possibility of developing an accurate tool using data mining algorithms for sex determination in the forensic framework.

• The Korean Journal of Pain
• /
• v.23 no.1
• /
• pp.11-17
• /
• 2010

Background: The target of lumbar sympathetic ganglion block is the anterolateral surface of the L2, 3 and 4 vertebral bodies, where the lumbar sympathetic ganglion usually lies. In most cases, a block-needle is inserted approximately 5-8 cm lateral to spinous process on the skin and directed to the anterolateral surface of vertebral body obliquely. The purpose of this study is to determine the safe entry angle and entry point in Korean by using the abdominal CT scan images. Methods: The abdominal CT images of eighty five patients were recruited to this study. The minimal angle aimed at the lumbar sympathetic ganglion that can pass through the lateral aspect of body and maximal angle that avoids puncturing the kidney, ureter or retroperitoneal space were measured. The distance from midline to skin entry point was also measured. Results: There was no significant difference in entry angle among L2, 3, and 4 level. The entry angle was similar in the right and left side, and in males and females. The entry angle of old age group was significantly smaller than that of young age group. The calculated safe entry angle was $30.5{\pm}0.4^{\circ}$ and entry point was $7.7{\pm}0.2\;cm$ and $6.7{\pm}0.1\;cm$ lateral from midline in males and females respectively. Conclusions: These measurements can be used as a reference for lumbar sympathetic ganglion block and radiofrequency lesioning. Prior to performing the lumbar sympathetic ganglion block for cancer patients, the abdominal CT scan should be reviewed to prevent complications.