• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.6
• /
• pp.1355-1362
• /
• 2007

In this paper, these setting can be useful in the microprocessor and sensor that designed to improve the efficiency of the photovoltaic system the photovoltaic position tracker device, and compared the normal photovoltaic system of fixed form with the photovoltaic system of solar position tracked form. Moreover, this is compared the catalogue of solar cell module and the simulation through a mathematics modelling with the solar cell's characteristic interpreting and that is composed an power conversion system with boost converter and voltage source inverter. This device can be used to the constant voltage control method for maximum power point tracking in boost converter control. Experiment Results is shown that using a SPWM(Sinusoidal Pulse Width Modulation) control method in inverter control.

• Current Photovoltaic Research
• /
• v.11 no.3
• /
• pp.75-78
• /
• 2023

Recently, the installation of photovoltaic modules in urban areas has been increasing. In particular, the demand for solar modules installed in a limited space is increasing. However, since the crystalline silicon solar module's size is proportional to the solar cell's size, it is difficult to manufacture a module that can be installed in a limited area. In this study, we fabricated a solar module with a shingled design that can control horizontal and vertical width using a bi-directional laser scribing method. We fabricated a string cell with a width of 1/5 compared to the existing shingled design string cells using a bi-directional laser scribing method, and we fabricated a solar module by connecting three strings in parallel. Finally, we achieved a conversion power of 5.521 W at a 103 mm × 320 mm area.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04b
• /
• pp.10-11
• /
• 2008

We developed the equipment palpating cell proliferation using a high brightness LED. This equipment was fabricated using a micro-controller and a high brightness LED, and designed to enable us to control light irradiation time, intensity, frequency and so on. Especially, to control the light irradiation frequency, FPGA was used, and to control the change of output value, TLC5941 was used. Control stage is divided into 30 levels by program. Consequently, the current value could be controlled by the change of level in Continue Wave(CW) and Pulse Width Modulation(PWM), and the output of a high brightness LED could be controlled stage by stage. And then, each experiment was performed to irradiation group and non-irradiation group for bone marrow cells. MIT assay method was chosen to verify the cell increase of two groups and the effect of irradiation on cell proliferation was examined by measuring 590nm transmittance of ELISA reader. As a result, the cell increase of bone marrow cells was verified in irradiation group as compared to non-irradiation group.

• 전기의세계
• /
• v.29 no.5
• /
• pp.321-328
• /
• 1980

The Q-switching oscillator of TE $M_{00}$ mode was constructed in order to improve the properties of energy focusing and amplification, and prevent laser materials from breakdown. The Q-switching was done by means of electro-optical effect using Glan prism and KDP Pockels cell. Sharp laser pulse of risetime-1 ns and variable pulse width 2-10 ns was obtained from Q-switching laser pulse by PTM method using a laser triggered spark gap (LTSG), Glan prism and Pockels cell. A single ultra-short pulse (picosec order in pulse width) was obtained from mode-locked pulse train in combination of a mode-locked oscillator using saturable dye cell with pulse shaping system using PTM method.d.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1149-1153
• /
• 2006

We developed the equipment palpating cell proliferation using a high brightness LED. This equipment was fabricated using a micro-controller and a high brightness LED, and designed to enable us to control light irradiation time, intensity, frequency and so on. Especially, to control the light irradiation frequency, FPGA was used, and to control the change of output value, TLC5941 was used. Control stage is divided into 30 levels by program. Consequently, the current value could be controlled by the change of level in Continue Wave(CW) and Pulse Width Modulation(PWM), and the output of a high brightness LED could be controlled stage by stage.

• Biomedical Science Letters
• /
• v.23 no.3
• /
• pp.208-214
• /
• 2017

To investigate the effects of strenuous physical exercise on commonly used hematological markers in subjects the intensive long running. Blood samples were obtained from nineteen participants in a 622 km ultra-marathon race before, 300 km and immediately after completion of the 622 km ultra-marathon. Samples were analyzed for total white cell count (WBC) and differential, total red cell count (RBC), hemoglobin, hematocrit, mean corpuscular volume (MCV), mean corpuscular hemoglobin (MCH), mean corpuscular hemoglobin concentration (MCHC), red cell distribution width (RDW), platelets, mean platelets volume (MPV), platelets distribution width (PDW). Significant increases were found in WBC, neutrophil and platelets at 622 km compared to the pre-race. RBC, hemoglobin and hematocrit decreased statistically significantly the race at 300 km and 622 km compared to pre-race. A wide range of hematological perturbations occur during 622 km ultra-marathon running but it was physiological changes within a reference range. The 622 km ultra-marathon is less likely to cause clinically significant hematologic changes in athletes.

• International journal of advanced smart convergence
• /
• v.9 no.2
• /
• pp.123-128
• /
• 2020

We constructed a cooling system for solar cells using convection phenomena and investigated its cooling performance. The cooling system didn't need any driving power or water resources. The convection cooler manufactured with a right-triangle shape of an air duct was attached to the rear of the solar cell to confirm that cooling was performed using convection phenomena. When the ratio of duct width to attachment surface width was 3:7, and the ratio of entrance height and exit height of duct was 5:1, it showed the best cooling performance. Comparative experiments with solar cells without convection cooler showed that cooling effects from 16.5℃ to 20.9℃ occurred after 40 minutes exposed to the 1300W Xenon lamp condition.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.89-90
• /
• 2006

The bipolar plate is a major component of the PEM fuel cell stack, which takes a large portion of stack cost. In this study, as alternative materials fur bipolar plate of PEM fuel cells, graphite composites were fabricated by compression molding. Graphite particles mixed with epoxy resin were used as the main substance to provide electric conductivity. Flow channels were fabricated by compression molding, and design of experiments (DOE) was applied to the tests to evaluate moldability. Results showed that land width and channel depth were two significant factors for moldability, and channel width had little influence on the moldability.

• Proceedings of the KIEE Conference
• /
• 1997.07e
• /
• pp.1749-1751
• /
• 1997

AC PDP with surface micro discharge has a structure that all discharge electrodes are arranged on the front glass panel, and the rear glass panel merely serves as a cover glass to form the micro discharge space. The relationships between the dischage voltage and the structure among such as electrode width, distance between electrodes, discharge space gap, and dielectric layer width are investigated.

• The Korean journal of internal medicine
• /
• v.33 no.6
• /
• pp.1234-1240
• /
• 2018

Background/Aims: Red blood cell distribution width (RDW) is a value representing the heterogeneity in the size of red blood cell, and it is usually used in distinguishing types of anaemia. Recently, it was reported that it could reflect the burden of inflammation in diverse diseases and their prognosis. Hence, in this study, we investigated whether RDW may contribute to discriminating adult onset Still's disease (AOSD) from sepsis in serious febrile patients within 24 hours after hospitalization. Methods: We reviewed the medical records and enrolled 21 AOSD patients, 27 sepsis patients and 30 matched healthy controls. We collected at least two laboratory results of variables including RDW within 24 hours after hospitalization, and we calculated their mean values. Results: Sepsis patients showed the significantly increased median white blood cell count, compared to AOSD patients ($14,390.0/mm^3$ vs. $12,390.0/mm^3$, p = 0.010). The median RDW in sepsis patients was higher than that in AOSD patients (15.0% vs. 13.3%, p = 0.001), and furthermore, the median RDW in both patient-groups was significantly higher than that in healthy controls. In contrast, the median ferritin level in sepsis patients was lower than that in AOSD patients (544.0 mg/dL vs. 3,756.6 mg/dL, p = 0.001). In multivariate analysis, RDW ${\geq}14.8%$ (odds ratio, 17.549) and ferritin < 2,251.0 mg/dL (odds ratio, 32.414) independently suggested sepsis more than AOSD in patients initially presenting with fever requiring hospitalization. Conclusions: RDW might be a rapid and helpful marker for a differential diagnosis between AOSD from sepsis at an early phase.