• 통합자연과학논문집
• /
• 제13권1호
• /
• pp.1-7
• /
• 2020

This paper proposes a novel fractional frequency reuse(FFR) based on dynamic user distribution. In the FFR, a macro cell is divided into two regions, i.e., the inner region(IR) and outer region(OR). The criterion for dividing the IR and OR is the distance ratio of the radius. However, these distance-based criteria are uncertain in measuring user performance. This is because there are various attenuation phenomena such as shadowing and wall penetration as well as path loss. Therefore, we propose a novel FFR based on dynamic user classification with signal to interference plus noise ratio(SINR) of macro users and classify the FFR into two regions newly. Simulation results show that the proposed scheme has better performance than the conventional FFR in terms of SINR and throughput of macro cell users.

• 대한기계학회논문집B
• /
• 제22권2호
• /
• pp.153-161
• /
• 1998

This study describes the results of the analysis of measured rotating stall signal in a centrifugal compressor with vaneless diffuser. Unsteady flow and rotating stall in vaneless diffuser were investigated by measuring of unsteady velocity fluctuation using hot-wire anemometer. Experiments were carried out in several impeller rotating speeds, at different radius ratios. Single hot -wire was used to study the characteristics of rotating stall. As a result, the abrupt rotating stall was detected at all measured impeller rotating speeds and the several flow coefficients which are less than 0.16. The number of the stall cell was one at all measured rotational speeds, and the rotating direction was the same as that of the impeller. As the flow rate decreased, the profile of the phase averaged radial velocity component with time changed from a sawtooth to a sine wave.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.174-179
• /
• 2004

The growth of the critical size bubble by diffusion process in viscoelastic medium was treated by an integral method for the concentration boundary layer adjacent to the bubble wall. In this study, we obtained a set of the first order time dependent equations to obtain bubble radius and gas pressure inside the bubble simultaneously. The calculated final cell sizes depending on the initial saturation pressure are in close agreement with the observed ones. The governing equations developed in this study may be used in polymer processing of microcellular foams.

• 한국통신학회논문지
• /
• 제33권3A호
• /
• pp.269-276
• /
• 2008

In this paper, we analyze the M-WiMAX UL capacity limits under 2-Tier cell layout, considering the effects of random user position, path loss models, fading channel and adjacent channel interference from WCDMA system. In order to make the analysis approximate to the practical system capacity, we propose a MCS-based capacity analysis method considering the effects of PER requirement and the utilized MCS levels in M-WiMAX system. The proposed MCS-based method is validated through a system-level Monte Carlo simulation. Furthermore, a comparison between the conventional Shannon method and the proposed MCS-based method is presented and the optimum cell radius is suggested.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.370-373
• /
• 1999

The purpose of this study is to research and develop PAn composite electrode for EDLC. EDLC cell of PAn composite electrode with 1M LiClO$_4$/PC brings out good capacitor performance below 4.0V. The radius of semicircle of PAn composite electrode adding 15wt% SP270 was absolutely small. The total resistance of EDLC cell mainly depended on internal resistance of the electrode. The discharge capacitance of PAn composite with 15wt% SP270 in 1st and 200th cycles was 42 and 42 F/g at current density of 1mA/cm$^2$. The capacitance of PAn composite with 15wt%. SP270 capacitor was larger than that of PAn capacitor without SP270. The coulombic efficiency of EDLC at discharge process of 1 and 200 cycles were 94 and 100% respectively. PAn composite EDLC with 15wt% SP270 content showed good capacitance and stability with cycling.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제17권2호
• /
• pp.260-264
• /
• 2017

Process variation effect on arch-structured gate stacked array (GSTAR) 3-D NAND flash is investigated. In case of arch-structured GSTAR, a shape of the arch channel is depending on an alignment of photo-lithography. Channel width fluctuates according to the channel hole alignment. When a shape of channel exceeds semicircle, channel width becomes longer, increasing drain current. However, electric field concentration on tunnel oxide decreases because less electric flux converges into a larger surface of tunnel oxide. Therefore, program efficiency is dependent on the process variation. Meanwhile, a radius of channel holes near the bottom side become smaller due to an etch slope. It also affects program efficiency as well as channel width. Larger hole radius has an advantage of higher drain current, but causes degradation of program speed.

• 한국세라믹학회지
• /
• 제52권5호
• /
• pp.380-383
• /
• 2015

We prepared the $TiO_2$ layer with 0 ~ 4 wt% of polystyrene (PS) beads having a radius of 250 nm to increase the dye adsorption and energy conversion efficiency (ECE) of a dye sensitized solar cell (DSSC). Then, we fabricated DSSCs using $0.45cm^2$ active area. FE-SEM was used to characterize the microstructure consisting of $TiO_2$ layer and PS beads. UV-VIS-NIR was used to determine the optical absorbance of working electrodes (WEs). Solar simulator and potentiostat were used to determine the photovoltaic properties. We observed that pores having a radius of 250 nm were formed with the density of $0.15ea/{\mu}m^2$ in $TiO_2$ layers after conducting the sintering process. The absorbance in visible light regime was found to increase with the increase in the amount of PS beads. The ECE increased from 4.66% to 5.25% when the amount of PS beads was increased from 0 to 4 wt%. This is because the pores of PS beads increased the adsorption of dye. Our results indicate that the ECE of the DSSCs can be enhanced by the addition of an appropriate amount of PS beads into $TiO_2$ layers.

• 한국융합학회논문지
• /
• 제13권3호
• /
• pp.197-202
• /
• 2022

CZTS 태양전지는 Cu, Zn, Sn, Se, S으로 구성된 흡수층을 사용하는 박막 태양전지로, In, Ga이 사용되는 CIGS 태양전지보다 저렴하며 Pb, Cd이 사용된 페로브스카이트, CdTe 태양전지보다 친환경적이다. 본 연구에서 우리는 유연기판인 Mo foil 위에 제작된 유연 CZTS 태양전지를 지정된 곡률만큼 휘게 하는 bending test를 진행하였다. 태양전지에 압축응력이 가해지는 inner benidng과 인장응력이 가해지는 outer bending의 방향에서 실험은 진행되었으며, 50 mmR의 곡률 반경으로 진행된 1,000 회의 굽힘 횟수 동안 태양전지의 효율은 최고 12.7%까지 감소하였으며, 두 방향 모두에서 효율 감소의 가장 큰 원인은 병렬저항의 큰 감소로 나타났다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 1999년도 추계종합학술대회
• /
• pp.462-466
• /
• 1999

고속 광대역 통신의 구현을 위하여 사용 주파수 대역이 밀리미터파 대에 근접함에 따라 마이크로파 신호 채널의 감쇠 특성을 고려한 필요성이 더욱 증대되고 있으며, 특히 B-WLL 시스템에 사용되는 27GHz 대역에서의 마이크로파 채널에 대하여는 강우감쇠로 인한 출력 보상을 반드시 고려하여야 한다. 그러나 어느 한 셀을 설계하면서 강우 감쇠를 고려하여 지나치게 방사 전력을 증가시키면 다른 셀의 수신장치에 간섭을 유발할 수 있다. 본 논문에서는 B-WLL 시스템의 주요 특성 및 인접 셀의 간섭으로 인하여 시스템 성능을 저하시키지 않을 정도로 전파신호 출력을 보상할 경우 적정한 셀 서비스 반경, 서비스 가능한 폭우의 한계 및 적응형 출력 제어 시스템에 대하여 고찰하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.413-413
• /
• 2012

Lead sulfide (PbS) Colloidal quantum dots (CQDs) are promising material for the photovoltaic device due to its various outstanding properties such as tunable band-gap, solution processability, and infrared absorption. More importantly, PbS CQDs have large exciton Bohr radius of 20 nm due to the uniquely large dielectric constants that result in the strong quantum confinement. To exploit desirable properties in photovoltaic device, it is essential to fabricate a device exhibiting stable performance. Unfortunately, the performance of PbS NQDs based Schottky solar cell is considerably degraded according to the exposure in the air. The air-exposed degradation originates on the oxidation of interface between PbS NQDS layer and metal electrode. Therefore, it is necessary to enhance the stability of Schottky junction device by inserting a passivation layer. We investigate the effect of insertion of passivation layer on the performance of Schottky junction solar cells using PbS NQDs with band-gap of 1.3 eV. Schottky solar cell is the simple photovoltaic device with junction between semiconducting layer and metal electrode which a significant built-in-potential is established due to the workfunction difference between two materials. Although the device without passivation layer significantly degraded in several hours, considerable enhancement of stability can be obtained by inserting the very thin LiF layer (<1 nm) as a passivation layer. In this study, LiF layer is inserted between PbS NQDs layer and metal as an interface passivation layer. From the results, we can conclude that employment of very thin LiF layer is effective to enhance the stability of Schottky junction solar cells. We believe that this passivation layer is applicable not only to the PbS NQDs based solar cell, but also the various NQDs materials in order to enhance the stability of the device.