• 한국자기학회지
• /
• 제18권1호
• /
• pp.14-18
• /
• 2008

본 연구에서는 Bi:YIG($Bi_{0.5}Y_{2.5}Fe_5O_{12}$) 막을 에어로졸 성막법을 이용하여 제작함에 있어서, 에어로졸을 구성하는 수송가스의 유량이 막의 자기적 특성과 광학적인 특성에 대하여 분석하였다. 직경 $100{\sim}500$ nm 의 Bi:YIG 분말을 질소 가스를 수송가스로 사용하여 성막을 실시하였고, 이 때, 수송가스의 유량은 0.5 l/min${\sim}10$ l/min 사이에서 변화시켰다. 수송가스의 유량이 증가할수록 Bi:YIG 막의 보자력은 51 Oe에서 37 Oe까지 지수함수적으로 감소하였다. 이것은 충돌에너지가 증가함에 따라 막내부 혹은 막표면의 결함이 감소하였기 때문이라고 고찰되었다. 포화자화는 유량이 증가할수록 감소하였는데, 이는 충돌에너지가 강해짐에 따라 결정이 왜곡되는 힘을 받았기 때문이라고 고찰되었다.

• 한국재료학회지
• /
• 제29권5호
• /
• pp.322-327
• /
• 2019

Hole carrier selective MoOx film is obtained by atomic layer deposition(ALD) using molybdenum hexacarbonyl[$Mo(CO)_6$] as precursor and ozone($O_3$) oxidant. The growth rate is about 0.036 nm/cycle at 200 g/Nm of ozone concentration and the thickness of interfacial oxide is about 2 nm. The measured band gap and work function of the MoOx film grown by ALD are 3.25 eV and 8 eV, respectively. X-ray photoelectron spectroscopy(XPS) result shows that the $Mo^{6+}$ state is dominant in the MoOx thin film. In the case of ALD-MoOx grown on Si wafer, the ozone concentration does not affect the passivation performance in the as-deposited state. But, the implied open-circuit voltage increases from $576^{\circ}C$ to $620^{\circ}C$ at 250 g/Nm after post-deposition annealing at $350^{\circ}C$ in a forming gas ambient. Instead of using a p-type amorphous silicon layer, high work function MoOx films as hole selective contact are applied for heterojunction silicon solar cells and the best efficiency yet recorded (21 %) is obtained.

• 한국재료학회지
• /
• 제11권7호
• /
• pp.599-602
• /
• 2001

전도성 고분자인 poupyrrole과 polyaniline을 이용하여 센서를 제조하고 휘발성 유기화합물에 대한감응특성 및 감지막의 물성을 조사하여 지금까지 알려지지 않은 감응 기구를 설명하고자 하였다. Polypyrrole과 polyaniline은 두께가 얇은 경우가 두꺼운 경우보다 감도가 높았으며, 1분간 도펀트를 제거한 센서가 가장 높은 감도를 나타내었다. 또한 두 가지 센서 모두 극성이 강한 분자가 흡착될수록 감도가 증가하였는데, 이는 극성을 갖는 분자가 감지막 내부로 침투하여 polaron 및 자유 carrier를 고착시키거나 추가의 자유 carrier를 형성하여 전도도에 변화를 주기 때문인 것으로 판단된다.

• 반도체디스플레이기술학회지
• /
• 제12권4호
• /
• pp.49-54
• /
• 2013

In this study, we have investigated the effect of the substrate temperature and oxygen flow rate on the characteristics of IZO thin films for the OLED (organic light emitting diodes) devices. For this purpose, IZO thin films were deposited by RF magnetron sputtering at room temperature and $300^{\circ}C$ with various $O_2$ flow rate. In order to investigate the influences of the oxygen, the flow rate of oxygen in argon mixing gas has been changed from 0.1sccm to 0.5sccm. IZO thin films deposited at room temperature show amorphous structure, whereas IZO thin films deposited at $300^{\circ}C$ show crystalline structure having an (222) preferential orientation regardless of $O_2$ flow rate. The electrical resistivity of IZO film increased with increasing flow rate of $O_2$ under Ar+$O_2$. The change of electrical resistivity with increasing flow rate of $O_2$ was mainly interpreted in terms of the charge carrier concentration rather than the charge carrier mobility. The electrical resistivity of the amorphous-IZO films deposited at R.T. was lower than that of the crystalline-IZO thin films deposited at $300^{\circ}C$. The change of electrical resistivity with increasing substrate temperature was mainly interpreted in terms of the charge carrier mobility rather than the charge carrier concentration. All the films showed the average transmittance over 85% in the visible range. The current density and the luminance of OLED devices with IZO thin films deposited at room temperature in 0.1sccm $O_2$ ambient gas are the highest amongst all other films. The optical band gap energy of IZO thin films plays a major role in OLED device performance, especially the current density and luminance.

• 반도체디스플레이기술학회지
• /
• 제11권4호
• /
• pp.25-30
• /
• 2012

In this study, we have investigated the effect of the substrate temperature and oxygen flow rate on the characteristics of IZO thin films for the organic light emitting diodes (OLED) devices. For this purpose, IZO thin films were deposited by RF magnetron sputtering at room temperature and $300^{\circ}C$ with various $O_2$ flow rate. In order to investigate the influences of the oxygen, the flow rate of oxygen in argon mixing gas has been changed from 0.1sccm to 0.5sccm. IZO thin films deposited at room temperature show amorphous structure, whereas IZO thin films deposited at $300^{\circ}C$ show crystalline structure having an (222) preferential orientation regardless of $O_2$ flow rate. The electrical resistivity of IZO film increased with increasing flow rate of $O_2$ under $Ar+O_2$. The change of electrical resistivity with increasing flow rate of $O_2$ was mainly interpreted in terms of the charge carrier concentration rather than the charge carrier mobility. The electrical resistivity of the amorphous-IZO films deposited at R.T. was lower than that of the crystalline-IZO thin films deposited at $300^{\circ}C$. The change of electrical resistivity with increasing substrate temperature was mainly interpreted in terms of the charge carrier mobility rather than the charge carrier concentration. All the films showed the average transmittance over 83% in the visible range.

• 반도체디스플레이기술학회지
• /
• 제12권2호
• /
• pp.33-37
• /
• 2013

In this study, we have investigated the effect of the substrate temperature and hydrogen flow rate on the characteristics of IZO thin films for the organic light emitting diodes (OLED) devices. For this purpose, IZO thin films were deposited by RF magnetron sputtering at room temperature and $300^{\circ}C$ with various $H_2$ flow rate. In order to investigate the influences of the oxygen, the flow rate of hydrogen in argon mixing gas has been changed from 0.1sccm to 0.9sccm. IZO thin films deposited at room temperature show amorphous structure, whereas IZO thin films deposited at $300^{\circ}C$ show crystalline structure having an (222) preferential orientation regardless of $H_2$ flow rate. The electrical resistivity of IZO film decreased with increasing flow rate of $H_2$ under Ar+$H_2$. The change of electrical resistivity with increasing flow rate of $H_2$ was mainly interpreted in terms of the charge carrier concentration rather than the charge carrier mobility. The electrical resistivity of the amorphous-IZO films deposited at R.T. was lower than that of the crystalline-IZO thin films deposited at $300^{\circ}C$. The increase of electrical resistivity with increasing substrate temperature was interpreted in terms of the decrease of the charge carrier mobility and the charge carrier concentration. All the films showed the average transmittance over 83% in the visible range.

• 한국진공학회지
• /
• 제16권2호
• /
• pp.110-115
• /
• 2007

Atomic layer deposition(ALD)에 유도결합 플라즈마 소스를 채용하여 plasma enhanced ALD(PEALD)장치를 제작하고 플라즈마 발생 실험을 수행하였다. ALD와 PEALD를 이용하여 기판온도 $230^{\circ}C$에서 p-type Si(100)기판 위에 Co박막을 증착하였다. 이때, $Co_{2}(CO)_{6}$을 Co전구체로, 암모니아를 반응가스로, 아르곤을 캐리어(carrier) 및 퍼지(purge)가스로 사용하였다. 증착된 Co박막의 구성성분과 박막의 두께를 auger electron spectroscopy(AES)와 field emission scanning electron microscopy(FESEM)을 이용하여 분석하였다. ALD와 PEALD를 이용하여 증착된 Co박막에서 모두 불순물이 발견되었는데, PEALD의 경우 ALD에 비해 불순물의 양이 약 반으로 감소되었다. 암모니아 플라즈마가 Co전구체에 포함된 탄소와의 반응을 매우 효과적으로 유도하는 것으로 확인되었다.

• 한국세라믹학회지
• /
• 제53권3호
• /
• pp.338-342
• /
• 2016

ZnO thin film co-doped with F and Al was prepared on a glass substrate via simple non-alkoxide sol-gel spin coating. For a fixed F concentration, the addition of Al co-dopant was shown to reduce the resistivity mainly due to an increase in electrical carrier density compared with ZnO doped with F only, especially after the second post-heat-treatment in a reducing environment. There was no effective positive contribution to the reduction in resistivity due to the mobility enhancement by the addition of Al co-dopant. Optical transmittance of the ZnO thin film co-doped with F and Al in the visible light domain was shown to be higher than that of the ZnO thin film doped with F only.

• 한국진공학회지
• /
• 제2권4호
• /
• pp.480-485
• /
• 1993

Factros considered building the magnetron sputtering system for TFT LCD (thin film transistor liquid crystal display0 metallization were thin film thichnes uniformity, temperature uniformity and the pressure gradient of sputtering gas flow in vacuum chamber, base pressure, and the stability fo the carrier moving . The system was consisted of a deposition chamber, a pre-heating chamber, a RF-precleaning chamber and a load/unload lock chamber. The system was designed to handle a substrate with dimension of 400$\times$400mm. The temperautre uniformity of a heater table developed showed $250 ^{\circ}C\pm$5% accuracyon the substrate glass. A base pressure of 1.8 $\times$10-7 torr was obtained after 24 hours pumping with a cryo pump. After an aluminum target was installed in a sputtering source and the film wa sdeposited on the glass, the uniformity, reflectivity and sheet resistance of the deposited film were measured.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 춘계학술대회 논문집
• /
• pp.188-193
• /
• 1997

ZnO thin film had been deposited on the glass 7r sputtering method, and investigated by electrical and structural properties. When the rf power was 188W and sputtering pressure was 1$\times$10$^{-3}$ Torr at room temperature, Al-doped ZnO thin film had the lowest resistivity(1$\times$10$^{-4}$ $\Omega$.cm), and then carrier concentration and Hall mobility were 6.27$\times$10$^{20}$ cm$^{-3}$ and 22.04$\textrm{cm}^2$/V.s, respectively. And undoped ZnO thin film had about 10$^{14}$ $\Omega$.cm resistivity when oxygen content was 10% or more at room temperature. The surface morphology of ZnO thin film observed by SEM was overall uniform when oxygen content was 50% below and sputtering pressure was 1.0$\times$10$^{-1}$ Torr.