• Journal of Hydrogen and New Energy
• /
• v.29 no.1
• /
• pp.1-10
• /
• 2018

The amount of biogas increases as the amount of organic waste increases. Recently, biogas from organic waste have been made much efforts to utilize as a energy. In particular, the concentration of $CH_4$ and $CO_2$ generated from sewage sludge and livestock manure treatment are 60-70% and 30-35%, and $CH_4$ and $CO_2$ generated from food wastes are 60-80% and 20-40%. In case of landfill gas, $CH_4$ and $CO_2$ have a concentration of 40-60% and 40-60% respectively. Therefore, in order to use the biogas more widely, it is necessary to convert the biogas to methanol, LNG or DME. In this study, experiments were conducted to produce hydrogen and carbon monoxide through various biogas reforming reactions on $Ni/Ce-ZrO_2/Al2O3$ catalysts. The experiment of synthetic gas synthesis was carried out on a wide concentrations of methane and carbon dioxide, which were the major constituents of biogas from various organic wastes. The effect of $(O_2+CO_2)/CH_4$ (=R') on the yields of hydrogen and carbon monoxide, the conversion rate of methane and carbon dioxide was investigated. Also simulation for syngas synthesis on the $CO_2$ reforming of $CH_4$ was computed by employing total Gibbs free energy minimization method using PRO/II simulator, and compared with the experimental results on wet and dry reforming reaction of biogas.

• Advances in environmental research
• /
• v.6 no.1
• /
• pp.1-14
• /
• 2017

New technologies or improvement of the existing technologies are required to enhance the efficiency of removal of pollutants from wastewater. In this study we attempted to produce and test the activated carbon produced from the refused tea waste for the removal of dyes from wastewater. The objectives of this investigation were to produce activated carbon from refused tea waste by chemical activation, evaluate its performance for the removal of color produced from Acid Yellow 36, and the modeling of its dye removal with the kinetic study. The activation was performed in two steps namely carbonization at $375{\pm}25^{\circ}C$ and chemical activation with HCl at $800^{\circ}C$ under the absence of Oxygen. Adsorption isotherms and kinetic studies were performed with a textile dye, Acid Yellow 36, at different concentrations (20-80 mg/L). The maximum dye removal (~90%) observed at 80 mg/L dye concentration and it reduced at low dye concentrations. Maximum adsorption (71.97 mg/g) was recorded at 96 h at $29{\pm}1^{\circ}C$. Low pH increased the dye adsorption (pH=2; 78.27 mg/g) while adsorption reduced at high pH levels indicating that the competition occurs in between OH- ions and AY36 molecules for the adsorption sites in RTAC. The Langmuir isotherm model clearly explained the dye adsorption, favorably, by RTAC. Moreover, kinetic studied performed showed that the pseudo second order kinetic model clearly describes the dye adsorption. Based on the results obtained in this study, it can be concluded that RTAC can be used for the removal of textile dyes.

• Korean Journal of Materials Research
• /
• v.31 no.9
• /
• pp.502-510
• /
• 2021

Hierarchically porous carbon materials with high nitrogen functionalities are extensively studied as high-performance supercapacitor electrode materials. In this study, nitrogen-doped porous carbon textile (N-PCT) with hierarchical pore structures is prepared as an electrode material for supercapacitors from a waste cotton T-shirt (WCT). Porous carbon textile (PCT) is first prepared from WCT by two-step heat treatment of stabilization and carbonization. The PCT is then nitrogen-doped with urea at various concentrations. The obtained N-PCT is found to have multi-modal pore structures with a high specific surface area of 1,299 m² g^-1 and large total pore volume of 1.01 cm³ g^-1. The N-PCT-based electrode shows excellent electrochemical performance in a 3-electrode system, such as a specific capacitance of 235 F g^-1 at 1 A g^-1, excellent cycling stability of 100 % at 5 A g^-1 after 1,000 cycles, and a power density of 2,500 W kg^-1 at an energy density of 3.593 Wh kg^-1. Thus, the prepared N-PCT can be used as an electrode material for supercapacitors.

• Clean Technology
• /
• v.30 no.3
• /
• pp.239-247
• /
• 2024

The removal of volatile organic compounds (VOCs) from spent polypropylene (PP) sourced from the bumpers and interiors of used cars was carried out by using high-temperature supercritical carbon dioxide (scCO₂) extraction. The recycled polymers from the bumpers and interiors contained other additives beside PP such as polyethylene (PE), talc, and carbon black, which modified the properties of PP. The crystallinity of the recycled bumper and interior PP was significantly lower than that of the virgin PP pellet. The decomposition temperatures of the recycled bumper and interior PP was slightly higher than that of the virgin PP pellet, while the melting and crystallization points were slightly lower. The effect of process conditions on VOC removal was studied by varying the time (2 ~ 720 min), pressure (6.4 ~ 14 MPa), and temperature (298 ~ 473 K). Since VOC removal at 2 min produced satisfying results, times below 2 min (10 ~ 120 s) were also studied. The main goal of scCO₂ extraction was to reduce the xylene content, as the xylene content of the recycled bumpers was higher than the allowable limit. A temperature above 373 K was needed to remove the xylene from the waste PP samples. The optimum condition for VOC removal from bumper waste was determined to be 433 K, 8 MPa, and 60 s. The car interior waste had VOC content within the allowable limit, so no further treatment was needed.

• Journal of Korean Society for Atmospheric Environment
• /
• v.26 no.6
• /
• pp.657-665
• /
• 2010

Carbon dioxide ($CO_2$) is known to be a major greenhouse gas partially emitted from waste combustion facilities. According to the greenhouse gas emission inventory in Korea, the quantity of the gas emitted from waste sector in 2005 represents approximately 2.5 percent of all domestic greenhouse gas emission. Currently, the emission rate of greenhouse gas from the waste sector is relatively constant partly because of both the reduced waste disposal in landfills and the increased amounts of waste materials for recycling. However, the greenhouse gas emission rate in waste sectors is anticipated to continually increase, mainly due to increased incineration of solid waste. The objective of this study was to analyze the property of Municipal Solid Waste (MSW) and estimate $CO_2$ emissions from domestic MSW incineration facilities. The $CO_2$ emission rates obtained from the facilities were surveyed, along with other two methods, including Tier 2a based on 2006 IPCC Guideline default emission factor and Tier 3 based on facility specific value. The $CO_2$ emission rates were calculated by using $CO_2$ concentrations and gas flows measured from the stacks. Other parameters such as waste composition, dry matter content, carbon content, oxidation coefficient of waste were included for the calculation. The $CO_2$ average emission rate by the Tier 2a was 34,545 ton/y, while Tier 3 was 31,066 ton/y. Based on this study, we conclude that Tier 2a was overestimated by 11.2 percent for the $CO_2$ emission observed by Tier 3. Further study is still needed to determine accurate $CO_2$ emission rates from municipal solid waste incineration facilities and other various combustion facilities by obtaining country-specific emission factor, rather than relying on IPCC default emission factor.

• Resources Recycling
• /
• v.19 no.5
• /
• pp.44-49
• /
• 2010

SiC powders have been recovered from silicon-containing waste slurry by carbothermal reduction method with carbon black. Large amount of silicon-containing waste slurry is generated from Solar Cell industry. In an environmental and economic point of view, retrieve of the valuable natural resource from the silicon waste is important. In this study, SiC powder recovered by the reaction ball-milled silicon powder from waste and carbon black at $1350^{\circ}C$ for 3h under vacuum condition. Physical properties of samples have been characterized using SEM, XRD, Particle size analyzer and FT-IR spectroscopy.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2019.10a
• /
• pp.134-134
• /
• 2019

Utilization of organic waste as a renewable energy source is promising for sustainability and mitigation of climate change. Pyrolysis converts organic waste to gas, oil, and biochar by incomplete biomass combustion. Biochar is widely used as a soil conditioner and adsorbent. Biochar adsorbs/desorbs metals and ions depending on the soil environment and condition to act as a nutrient buffer in soils. Biochar is also regarded as a carbon storage by fixation of organic carbon. Phosphorus (P) and nitrogen (N) are strictly controlled in many wastewater treatment plants because it causes eutrophication in water bodies. P and N is removed by biological and chemical methods in wastewater treatment plants and transferred to sludge for disposal. On the other hand, P is an irreplaceable essential element for all living organisms and its resource (phosphate rock) is estimated about 100 years of economical mining. Therefore, P and N recovery from waste and wastewater is a critical issue for sustainable human society. For the purpose, intensive researches have been carried out to remove and recover P and N from waste and wastewater. Previous studies have shown that biochars can adsorb and desorbed phosphates implying that biochars could be a complementary fertilizer. However, most of the conventional biochar have limited capacity to adsorb phosphates and nitrate. Recent studies have focused on biochar impregnated with metal salts to improve phosphates and nitrate adsorption by synthesizing biochars with novel structures and surface properties. Metal salts and metal oxides have been used for the surface modification of biochars. If P removal is the only concern, P adsorption kinetics and capacity are the only important factors. If both of P and N removal and the application of recovery are concerned, however, P and N desorption characteristics and bioavailability are also critical factors to be considered. Most of the researches on impregnated biochars have focused on P removal efficiency and kinetics. In this study, coffee waste is thermally treated to produce biochar and it was impregnated with Mg/Al to enhance phosphates and nitrate adsorption/desorption and P bioavailability to increase its value as a fertilizer. Kinetics of phosphates and nitrate adsorption/desorption and bioavailability analysis were carried out to estimate its potential as a P and N removal adsorbent in wasewater and a fertilizer in soil.

• Journal of Microbiology and Biotechnology
• /
• v.16 no.7
• /
• pp.999-1009
• /
• 2006

Physiological, biochemical and genetic studies of Corynebacterium glutamicum, a workhorse of white biotechnology used for amino acid production, led to a waste knowledge mainly about amino acid biosynthetic pathways and the central carbon metabolism of this bacterium. Spurred by the availability of the genome sequence and of genome-based experimental methods such as DNA microarray analysis, research on genetic regulation came into focus. Recent progress on mechanisms of genetic regulation of the carbon, nitrogen, sulfur and phosphorus metabolism in C. glutamicum will be discussed.

• Advances in materials Research
• /
• v.13 no.3
• /
• pp.221-232
• /
• 2024

Waste tire management and recycling have grown to be significant issues because they bring up a global environmental concern. Thus, turning recycled waste tires into useful products may help tackle the environmental issue. This research aims to study and compare the effect of recycled carbon black (rCB) and commercial carbon black (CB) at certain 15 vol. % of filler loading on the mechanical, thermal, morphology and electrical properties of epoxy/CB composites. For this project, epoxy resin, diethyltoluenediamine (DETDA), recovered carbon black (rCB) and commercial carbon black (CB) graded N330, N550, N660 and N774 were mixed and compared accordingly to the formulation determined. The CB content was dispersed in the epoxy matrix using the mechanical mixing technique. The distribution and dispersion of CB in the epoxy matrix affect the characteristics of the conductive composites. rCB content at 15 vol% was selected at fixed content for comparison purposes due to the optimum value in electrical conductivity results. The flexural strength results followed the sequence of rCB>N774>N660>N550>N330. As for electrical conductivity results, epoxy/N330 exhibited the highest conductivity value, while the others achieved a magnitude of X10^-3 due to the highest external surface area of N330. In terms of thermal stability, epoxy/N330 and epoxy/N774 were slightly more stable than epoxy/rCB.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.2
• /
• pp.947-953
• /
• 2012

In this study we investigated the manufacturing method for the activated carbon using the char from the pyrolysis of waste tire. The physical activation method using the steam in the fixed-bed quartz reactor was used for preparation of activated carbon. The primary experiment parameters are the activation temperature, activation time, heating rate, and the injection quantity of active agent. From the results of pore distribution of activated carbon, the micropore which was made in $850^{\circ}C$ of activation temperature, $5^{\circ}C$/min of heating rate, and 3 hours of activation time was developed in biggest quantity, and mesopore and macropore were developed in the biggest quantity too. The optimum conditions for producing the activated carbon using the pyrolysis residue were $850^{\circ}C$ of activation temperature, 3 hours of activation time, $5^{\circ}C$/min of heating rate, and 3 g $H_2O/char-g{\cdot}hr$ of active agent through this study. The produced activated carbon in these conditions showed that the potentiality of utilization as activated carbon because the BET specific surface area was $517.6m^2/g$ and total pore volume was $0.648cm^3/g$.