• Journal of the Korean Ceramic Society
• /
• v.46 no.4
• /
• pp.357-364
• /
• 2009

We investigate a method for the electrochemical preparation of titanium dioxide/carbon nanotube ($TiO_2$/CNT) composites involving the electroplating of Ti in a titanium n-butoxide (TNB) electrolyte into a CNT matrix. The BET surface areas of $TiO_2$/CNT composites decreased as electrochemical operating time increased. Changes in XRD patterns showed a typical anatase type on the $TiO_2$/CNT composite prepared with a CNT matrix by the electroplating method in the TNB solution. In SEM micrographs, the titanium complex particles were uniformly distributed on the CNT surface. The results of chemical elemental analysis for the $TiO_2$/CNT composites showed that most of the spectra for these samples produced stronger peaks for carbon and Ti metal than those of any other element. Finally, the prominent photoelectrocatalytic (PEC) activities of the $TiO_2$/CNT composites could be attributed to the combined effects of photodegradation of $TiO_2$, electron assistance of CNT and the application of a sufficient voltage.

• Journal of Korean Society of Forest Science
• /
• v.102 no.4
• /
• pp.608-616
• /
• 2013

The objective of this study was to suggest contingent valuation method, simple random sampling method, systematic sampling method, maximum practice area method, and overlay practice area method as the estimation methods for forest management area to estimate carbon dioxide sink by forest management as stated in Article 3.4 of the Kyoto Protocol. A case study for Chungcheongbuk-do was performed using maximum practice area method which was thought of as the most rational method within MRV(Measurable, reportable and verifiable). The forest management ratio was defined as forest management area over the total forest area. Based on the definition of forest management activity, forest area was divided into practice forest land and non-practice forest land. The area of forest mangement for practices was based on the 'National Forest Management Information System' and the history of practices from the 'Proposals on Private Management Information Database'. The area of forest management for non-practices was based on the public used forest land from 'Categorial map of forest land'. It was shown that the forest management area of Chuncheongbuk-do was 115,566 ha for practice forest land, and 131,008 ha for non-practice forest land. The forest managent ratio was 49.7% of the total forest area of 495,806 ha. This study made possible to the estimation of the forest management ratio under Kyoto Protocol, and had an advantage in searching for a practical method of forest management plan in which the forest management ratio could be enhanced.

• Spatial Information Research
• /
• v.22 no.2
• /
• pp.1-9
• /
• 2014

UN-REDD (United Nations programme on Reducing Emissions from Deforestation and forest Degradation in Developing Countries) and AR-CDM (Afforestation/Reforestation-Clean Development Mechanism) is currently being emerged as one of important mechanism to reduce carbon dioxide in relation to the deforestation. Discussion on North Korea as UN-REDD/AR-CDM project target continues with a view to preventing deforestation and to securing CER(certified emission reduction) for South Korea. The forests in Mt. Baekdu are degraded, deforestation is occurred, nevertheless, portion of forested area is still high, where both REDD and AR-CDM investment potential are quite high. Accordingly, this study is intended to explore a simultaneous registration potential to UNREDD/AR-CDM for Mt. Baekdu although separate registration to UN-REDD or AR-CDM has already gained worldwide recognition as a typical method in the process of GHG (Greenhouse Gas) reduction project. The results indicate that selecting UN-REDD or AR-CDM in accordance with sub-watershed forest condition could capture 53.2% more carbon dioxide than REDD alone and 21.9% more than AR-CDM alone. It is anticipated that this research output could be used as a realistic evidence to introduce carbon sequestering project in accordance with sub-watershed forest condition.

• Membrane Journal
• /
• v.22 no.2
• /
• pp.128-134
• /
• 2012

In this study, hydroxy polyimide (HPI) was prepared for non-porous membrane by solvent evaporation method. As the result of gas permeance properties measurement, $CO_2$ permeability was 85 Barrer and the $CO_2/N_2$ selectivity was 23 at $30^{\circ}C$. Flat sheet membrane and hollow fiber membrane were prepared by using ternary system of polymer, solvent and non-solvent additive. Morphologies and gas permeance properties were measured by FE-SEM and bubble flow meter. Each $CO_2$ permeability of 18.28 GPU, 70 GPU and $CO_2/N_2$ selectivity of 6.72, 8.63 at $30^{\circ}C$ in the flat sheet membrane and hollow fiber membrane. Hollow fiber membrane has gas permeance property better than flat sheet membrane.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.244.1-244.1
• /
• 2010

Bio energy development by using Low Calorific Gas Turbine(LCGT) has been developed for New & Renewable energy source for next generation power system, low fuel and operating cost method by using the renewable energy source in landfill gas (LFG), Food Waste, water waste and Livestock biogas. Low calorific fuel purification by pretreatment system and carbon dioxide fixation by green house system are very important design target for evaluate optimum applications for bio energy. Main problems and accidents of Low Calorific Gas Turbine system was derived from bio fuel condition such as hydro sulfide concentration, siloxane level, moisture concentration and so on. Even if the quality of the bio fuel is not better than natural gas, LCGT system has the various fuel range and environmental friendly power system. The mechanical characterisitics of LCGT system is a high total efficiency (>70%), wide range of output power (30kW - 30MW class) and very clean emmission from power system (low NOx). Also, we can use co-generation system. A green house designed for four different carbon dioxide concentration from ambient air to 2000 ppm by utilizing the exhaust gas and hot water from LCGT system. We look forward to contribute the policy for Renewable Portfolio Standards(RPS) by using LCGT power system.

• Clean Technology
• /
• v.21 no.2
• /
• pp.124-129
• /
• 2015

The constant-volume method was used to determine the solubility of CO₂ in various physical absorbents such as DMPEG (dimethyl ether of polyethylene glycol), DEC (diethyl carbonate), DMC (dimethyl carbonate), and TAT (triacetin) in the total pressure range from 5 to 30 bar. The Peng-Robinson equation of state has been used to describe the equilibrium behavior of these mixtures. It was found that the solubility of absorbents was in the of DMPEG250 > TAT > DEC > DMC at the same temperature. Futhermore, the solubiity of blended absorbent of DMPEG250 and DEC is higher than that of DMPEG 250 alone. Therefore, blended absorbent of DMPEG250 and DEC is expected to be an effective and low cost absorbent for physical absorption in precombustion CO₂ capture.

• KSBB Journal
• /
• v.23 no.3
• /
• pp.193-198
• /
• 2008

In this study, the supercritical $CO_2$ extraction was applied for the enrichment of coffee flavors. The extraction efficiency of coffee flavors was dependent on the pressure and temperature and optimized as 350 bar and 80$^\circ$C. Five flavors of high aroma values were analyzed. The flavors extracted by the supercritical $CO_2$ extraction were 76.6 times higher than those by the traditional method, espresso extraction. The modified headspace system proved the enhanced efficiency of supercritical $CO_2$ extraction. The coffee beverage containing the extract of supercritical $CO_2$ resulted 2.3 times of flavor enrichment when it was compared to that without the supercritical extract.

• Applied Chemistry for Engineering
• /
• v.27 no.1
• /
• pp.80-85
• /
• 2016

The carbon dioxide adsorption behavior of silica with a large specific surface area and pore volume functionalized with aminosilane compounds via in-situ polymerization and functionalization method were investigated. The organosilanes include amino functional group capable of adsorbing carbon dioxide. Elemental analyzer, in situ FT-IR and thermogravimetric analyzer were used to characterize the sorbents and to determine their $CO_2$ adsorption behavior. Comparison of different aminosilane loading in the support revealed that polyaminosilane functionalization of 70% of the pore volume in the support was better in terms of the adsorption capacity and amine efficiency than that of 100% of the pore volume of the support. Furthermore, the sorbents showed a higher adsorption capacity at an adsorption temperature of $75^{\circ}C$ than at $30^{\circ}C$ due to the thermal expansion of synthesized polyaminosilanes inside the pore of silica. The N-[3-(trimethoxysilyl)propyl]ethylenediamine (2NS) sorbent with 70% of the pore volume functionalized showed the highest adsorption capacity of 9.2 wt% at $75^{\circ}C$.

• Journal of the Korean Institute of Gas
• /
• v.9 no.3 s.28
• /
• pp.49-54
• /
• 2005

This work was to calibrate Anton Paar 512P vibrating tube densimeter which is a special type for density measurement under high pressure (up to 70 MPa) and temperature (up to 420 K) and checked the validity of the new apparatus. Calibration was peformed with water, nitrogen and water, vacuum as reference fluids. Temperature is measured from 313.15 K and 353.15 K at 10 K intervals, and pressure is measured up to 30 MPa at 5 MPa intervals, respectively. To check the validity of new apparatus and the calibration method we compared the values obtained by measuring density of carbon dioxide with those given by NIST Thermophysical Properties of Pure Fluids Database. The average deviations between the NIST and the experimental data were $0.3\%$ with water and nitrogen as reference fluids.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.30 no.1
• /
• pp.75-86
• /
• 2020

Objectives: In this study, we assessed respiratory hazards in the working environment as the work-relatedness of occupational diseases were examined. Methods: The subjects of the study were three Korean meat roasting restaurants, one Chinese restaurant, and two cafeterias. Measurement items were total dust, respirable dust, fine dust (PM_2.5), PAHs, TVOCs, temperature, humidity, carbon monoxide, carbon dioxide, and nitrogen dioxide. Results: The concentration of total dust and respiratory dust in the restaurant was low. Most PAHs were undetectable, but some Napthalene and Acenaphthylene was detected. Thirteen kinds of PAHs were detected in one sample of roasted meat, and Benzo(a)pyrene was 1.496 ㎍/㎥. PM_2.5, TVOCs, CO, and CO₂ were instantaneously high, but the average concentration was low. NO₂ was not detected. Conclusions: The results show that harmful substances such as PM_2.5, PAHs, CO, and TVOCs were generated in the air in the catering industry. When roasting meat, Benzo(a)pyrene, a carcinogen related to lung cancer, was generated among PAHs. Lung cancer can occur when working for a long time in such a working environment. Therefore, it is necessary to improve the working environment for the health of restaurant workers, and it is necessary to evaluate the concentration of harmful substances by cooking method through further research.