• Journal of the Korean Institute of Telematics and Electronics
• /
• v.14 no.4
• /
• pp.15-21
• /
• 1977

In this paper, an analogical method for measuring the electrical characteristics of the silent discharge in the Na2CO3 electrolyte is proposed by using an electrical equivalent model which consist of charging and discharging circuits. The electrical equivalent model is constructed with the use of zener diode and capacitor, and the electrical characteristics can be obtained by the voltage and charge traces which appear a simple parallelogram on the oscilloscope. The area enclosed by the parallelogram could be considered of the energy input per cycle, and is independent of the applied voltage waveform but dependent on the maximum applied voltage.

• Journal of Electrical Engineering and Technology
• /
• v.5 no.4
• /
• pp.580-591
• /
• 2010

This paper deals with an observer design for a P-Cell Chopper. The goal is to reduce drastically the number of sensors in such system by using an observer in order to estimate all the capacitor voltages. Furthermore, considering an instantaneous model of a p-cell chopper, an interconnected observer is designed in order to estimate the capacitor voltages and some parameters of the model. This is realized by using only the load current measurement. Simulation results are given in order to illustrate the performance of such observer. To show the validity of our approach, experimental based a DSP results are presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.12
• /
• pp.1276-1282
• /
• 2003

The SMT(Surface Mount Type) ferrite bead used to reduce the influx of power bus noise is modeled with parallel capacitor(C), series resistor(R) and series inductor(L). The simple equivalent circuit modeling doesn't agree with the measurement result. In this paper, we proposed the accurate equivalent circuit model of the ferrite bead at wide frequency range(50 MHz∼3 GHz) and analyzed the noise effect to the high speed IC(Integrate Circuit) with ferrite bead or not.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.2
• /
• pp.176-183
• /
• 2014

Three-phase four-wire distribution systems are used for both three-phase three-wire loads and single-phase two-wire consumer appliances in South Korea, Myanmar and other countries. Unbalanced load conditions frequently occur in these distribution systems. These unbalanced load conditions cause unbalanced voltages for three-phase and single-phase loads, and increase the loss in the distribution transformer. In this paper, we propose constant DC capacitor voltage control based strategy for the active load balancer (ALB) in the three-phase four-wire distribution systems. Constant DC capacitor voltage control is always used in active power line conditioners. The proposed control strategy does not require any computation blocks of the active and reactive currents on the distribution systems. Balanced source-side currents with a unity power factor are obtained without any calculation block of the unbalanced active and reactive components on the load side. The basic principle of the constant DC capacitor voltage control based strategy for the ALB is discussed in detail and then confirmed by both digital computer simulations using PSIM software and prototype experimental model. Simulation and experimental results demonstrate that the proposed control strategy for the ALB can balance the source currents with a unity power factor in the three-phase four-wire distribution systems.

• Journal of Power Electronics
• /
• v.18 no.2
• /
• pp.482-491
• /
• 2018

The practical design methodology of a three-phase dual active bridge (3ph-DAB) converter applied to low voltage direct current (LVDC) applications is proposed by using a mathematical model based on the steady-state operation. An analysis of the small-signal model (SSM) is important for the design of a proper controller to improve the stability and dynamics of the converter. The proposed lead-lag controller for the 3ph-DAB converter is designed with a simplified SSM analysis including an equivalent series resistor (ESR) for the output capacitor. The proposed controller can compensate the effects of the ESR zero of the output capacitor in the control-to-output voltage transfer function that can cause high-frequency noises. In addition, the performance of the power converter can be improved by using a controller designed by a SSM analysis without additional cost. The accuracy of the simplified SSM including the ESR zero of the output capacitor is verified by simulation software (PSIM). The design methodology of the 3ph-DAB converter and the performance of the proposed controller are verified by experimental results obtained with a 5-kW prototype 3ph-DAB converter.

• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.849-860
• /
• 2016

The high-switching-frequency operation of power converters can achieve high power density through size reduction of passive components, such as capacitors, inductors, and transformers. However, a small-output capacitor that has small capacitance and low effective series resistance changes the small-signal model of the converter power stage. Such a capacitor can make the converter unstable by increasing the crossover frequency in the transfer function of the small-signal model. In this paper, the design and implementation of a high-frequency LLC resonant converter are presented to verify the power density enhancement achieved by decreasing the size of passive components. The effect of small output capacitance is analyzed for stability by using a proper small-signal model of the LLC resonant converter. Finally, proper design methods of a feedback compensator are proposed to obtain a sufficient phase margin in the Bode plot of the loop gain of the converter for stable operation at 500 kHz switching frequency. A theoretical approach using MATLAB, a simulation approach using PSIM, and experimental results are presented to show the validity of the proposed analysis and design methods with 100 and 500 kHz prototype converters.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.13 no.2
• /
• pp.5-13
• /
• 1976

An analytical and experimental design procedure is described for the Capacitor Discharge Ignition (CDI) System with a view to fuel saving ann reduction of gas exhaustion and maintenance need. Specifically, the input and output voltage and current of a given ignition coil were calculated by using a simplified circuit model for the discharging system. The results were compared with the experimental results, from which ratings of the charging capacitor, the SCR and the diodes and the required output valtage of the DC.DC converter were determined so as to satisfy the optimum ignition conditions. Protection circuits for excessive dv/dt and di/dt for the SCR were also analyzed and the results were compared with the observed results, which facilitate selection of the SCR and design of the protection circuit and the trigger circuit. Also, design of the DC.DC converter was simplified based on the analysis and experimental results of the behavior of the converter, An experimental, yet practical CDI system was built, which showed satisfactory performance in the laboratory and field tests. The results were also reported.

• Proceedings of the KIPE Conference
• /
• 1996.06a
• /
• pp.89-92
• /
• 1996

This paper describes a detailed simulation model of the static condenser (STATCON) to analyze the dynamic interaction with the ac transmission line. The static condenser was represented by a 12-pulse voltage-source inverter sharing an energy storage dc capacitor. The voltage-source inverter consists of two 6-pulse bridges modeled with ideal gate-turn-off switches. The control system for the static condenser was designed through a mathematical model deduced from the equivalent circuit. Simulation results show that the conceived model is very effective to analyze the dynamic interaction between the static condenser and the ac transmission system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.04a
• /
• pp.392-393
• /
• 2014

Multilayer ceramic capacitors (MLCCs) have become one kind of the most widely used electrical components in recent decades. And the technology of MLCCs is developing continuously towards a direction of high capacitance and miniaturization. While the tiny thickness and the large quantity of the layers often make it very troublesome to do analysis with the full model MLCCs. In order to solve this problem, reduced model with fewer layers of MLCC was designed and verified in this paper.

• Proceedings of the KIEE Conference
• /
• 2002.11b
• /
• pp.171-173
• /
• 2002

This paper presents a power system decomposition technique for digital simulation of large power system. To decompose power system, distributed transmission line model is used. But this model can be used only for long transmission lines. In this paper, capacitor compensation method is proposed to use distributed transmission line model for short transmission line. And case study shows proposed method can be used for effective power system decompositon in digital simulation of large power system.