• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.24-25
• /
• 2006

In this paper, ZnO thin films were prepared on p-Si(100) by RF magnetron sputtering. Before the depostion, the substrates were pre-heated to 500, 400, 300, $200^{\circ}C$ or not. During the deposition, the substrates were cooled down naturally or kept and then the films were investigated by XRD(X-ray diffraction) and SEM (scanning micro scope). It is showed the most outstanding result that the film was prepared on the substrate were cooled from $400^{\circ}C$. When the substrate was cooled from a certain temperature during deposition, it could be improve the c-axis orientation and useful for application of SAW(surface acoustic wave) filter and FBAR(film bulk acoustic wave resonator) device.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.12
• /
• pp.1108-1114
• /
• 1998

$BaTiO_3$ thin films preferred c-axis orientation for the potential application of ferroelectric memory devices were deposited on silicon substrates(100) by RF sputtering and annealed at 800 and 900[$^{\circ}C$] in air. The BT(100)/BT(110) peak ratio of the sputtered sample was decreased with post-annealing in air. According to increasing with annealing temperature and time, the peak ratio of BT(100)/BT(110) was decreased and the surface density of thin film was high. Dielectric characteristics of $BaTiO_3$ thin film was measured as a function of annealing temperature and frequency. The dielectric constants were increased with annealing and decreased with frequency by space charge polarization and dipole polarization below 600[kHz]. The remanent polarization and coercive field in P-E hysteresis loop of $BaTiO_3$thin film were increased with the annealing temperature in air. The remanent polarization and coercive filed annealed at 800[$^{\circ}C$] for 1hr were 1.2[$\mu$C/$cm^2$] and 200[kV/cm]

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.397-398
• /
• 2005

Ferroelectric Lithium niobate ($LiNbO_3$) thin films are fabricated on $Al_2O_3$(0001) substrate using Pulsed Laser Deposition (PLD). The various deposition conditions such as substrate temperature, oxygen pressure, and post annealing condition are investigated to deposite c-axis oriented $LiNbO_3$ thin films. Highly c-axis oriented thin films are obtained under the conditions of working pressure of 100 mTorr, deposition for 10 min at $450^{\circ}C$, and in-situ annealing for 40 min. The $LiNbO_3$ thin films are chemically etched after electric poling and the etched configurations are studied by scanning electron microscope (SEM).

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.6
• /
• pp.237-241
• /
• 2014

We investigated the optimal etching conditions and properties of the surface change due to molten KOH/NaOH chemical wet etching using an AlN wafer which has been put to practical use in the present study. Results were observed using a scanning electron microscope after 5 minutes etching at $350^{\circ}C$, was found to have a surface form of the respective other Al-face, the N-face. In particular, etch-pit in the form of a hexagon, which is observed in the Al-face appeared, It was calculated at $2{\times}10^6/cm^2{\sim}10^{10}/cm^2$ dislocation density. In the case of N-face, lattice defects in the form of the hexagonal pyramids is formed. It was discovered that in order to observe the orientation of the wafer, which corresponds to the C-axis direction of the resulting hexagonal AlN which was analyzed using XRD (0002) and is a state of being oriented in the (0004) plane. The Radius of curvature of AlN wafer was 1.6~17 m measured by DC-XRD rocking curve position.

• Journal of Sensor Science and Technology
• /
• v.6 no.1
• /
• pp.49-55
• /
• 1997

ZnO thin film had been deposited on the glass by sputtering method, and investigated by optical and electrical properties. When the rf power was 180W and sputtering pressure was $1{\times}10^{-3}$Torr at room temperature, thin lam deposited had strongly oriented c-axis and the lowest resistivity($1{\times}10^{-4}{\Omega}{\cdot}cm$), and then carrier concentration and Hall mobility were $6.27{\times}10^{20}cm^{-3}$ and $22.04cm^{2}/V{\cdot}s$, respectively. Transmittance of ZnO thin film in visible range was above 90%, and this thin film cut of the ultraviolet range below 320nm and the infrared range above 850nm. And after annealing in hydrogen atmosphere, the resistivity of ZnO thin film was somewhat decreased, while obtained as stable state.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.22-22
• /
• 2009

최근 산화물 반도체와 나노소자 대한 관심이 날로 높아지고 있는 가운데 산화아연(ZnO) 나노구조를 이용한 나노소자 제작이 많이 연구되고 있다. 산화아연은 c축으로 우선 배향성을 가지는 우르짜이트 구조로써, 나노선 성장이 다른 산화물에 비해 용이하고 그 물리적, 화학적 특성이 안정 무수하다. 이러한 산화아연 나노선 제작법 가운데, 유기금속화학기상증착법은 다른 성장법에 비해 결정학적 광학적 특성이 우수하고 성장속도가 빨라 고품질 나노선 성장에 용이한 장비로 각광받고 있다. 하지만 bottom-up 공정을 기반으로 한 나노소자제작에서 몇 가지 문제점을 가지고 있다. 1) 수직형 대면적 성장, 2) 나노선 밀도 조절의 어려움, 3) 기판과의 계면층에 자발적으로 생성되는 계면층의 제거, 4) 고온성장시 precursor의 증발 문제 등이 그것이다. 본인은 이러한 문제점을 해결하기 위해 산화아연 나노구조 성장 시, 마그네슘(Mg)을 도입하여, 각 원소의 함량 분포 정도에 따라 기판 표면에 30nm 두께 미만의 상분리층(단결정+비정질층)을 자발적으로 형성시켰다. 성장이 진행됨에 따라, 아연이 rich한 단결정 층에서는 나노선이 선택적으로 성장하게 하였고, 마그네슘이 rich한 비정질 층에서는 성장이 이루어지지 않게 하였다. 따라서 산화아연이 증발되는 온도영역에서 10nm 이하 직경을 가지는 나노선을 자발적으로 계면층 없이 수직 성장하였다. 또한, 표면의 단결정, 비정질의 사이즈를 Mg 함량으로 적절히 조절한 결과, 산화아연계 나노월 구조성장이 가능하였다.

• Journal of the Korean Ceramic Society
• /
• v.41 no.6
• /
• pp.476-480
• /
• 2004

AZO (Al-doped ZnO) thin films were deposited on glass by pulsed magnetron sputtering method, and their structural, electrical and optical properties were investigated. XRD patterns showed that a highly c-axis preferred AZO film was grown in perpendicular to the substrate when pulse frequency of 30 ㎑ was applied to the target. Microstructure of thin films showed that the fibrous grain of tight dome shape was grown. The deposition rate decreased linearly with increase of pulse frequency, and the lowest resistivity was 8.67${\times}$10$\^$-4/ $\Omega$-cm for the film prepared at pulse frequency of 30 ㎑. The optical transmittance spectra of the films showed a very high transmittance of 85∼90%, within visible wavelength region and exhibited the absorption edge of about 350 nm. The characteristics of the low electrical resistivity and high optical transmittance of AXO films suggested a possibility for the application to transparent conducting oxides.

• Journal of the Korean Vacuum Society
• /
• v.10 no.1
• /
• pp.22-26
• /
• 2001

Microstructures of AlN thin films on Si substrates grown by plasma assisted molecular beam epitaxy were analyzed with various growth temperatures and substrate orientations. Reflection high energy electron diffraction (RHEED) patterns were checked for the in-situ monitoring of the growth condition. X-ray diffraction(XRD), double crystal X-ray diffraction (DCXD), and transmission electron microscopy/diffraction (TEM/TED) techniques were employed to characterize the microstructure of the films after growth. On Si(100) sub-strates, AlN thin films were grown mostly along the hexagonal c-axis orientation at temperature higher than $850^{\circ}C$. On the other hand the AlN films on Si(111) were epitaxially grown with directional coherencies in AlN(0001)/Si(111), AlN(1100)/Si(110), and AlN(1120)/Si(112). The microstructure of AlN thin films on Si(111) substrates, with a full width at half maximum of almost 3000 arcsec at 2$\theta$=$36.2^{\circ}$, showed that the single crystal films were grown, even if they includ a lot of crystal defects such as dislocations and stacking faults.

• Korean Journal of Materials Research
• /
• v.4 no.1
• /
• pp.90-96
• /
• 1994

ZnO thin films were deposited using Diethylzinc and $N_{2}O$ gas by plasma enhanced CVD (PECVD) at low substrate temperatures below $300^{\circ}C$. The effect of deposition parameters on the growth rate and the structural properties was determined at various deposition conditions. Crystallized ZnO thin films were successfully deposited even at $150^{\circ}C$ of substrate temperature. Above $200^{\circ}C$ c-axis oriented ZnO thin films, of which a standard deviation of X-ray rocking curve was less than $6^{\circ}$. were deposited on glass substrates. The variation of deposition rate showed different trends depending on substrate temperature and rf-input power. According to the deposition rate behavior as a function of substrate temperature, the transition points were observed resulting from crystallization of ZnO thin films. The activation energies for the deposition of ZnO thin films were 3.1KJ/mol and 1.9KJ/mol for the rf powers of 200W and 250W, respectively.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.88-92
• /
• 2003

In this paper, the characteristics of the ZnO films deposited on AI bottom electrode and the temperature effects on the ZnO film growth are presented along with the fabrication and their evaluation of the film bulk acoustic wave resonator (FBAR) devices. All the films used in this work were deposited using a radio-frequency (RF) magnetron sputtering technique. Growth characteristics of the ZnO films are shown to have a strong dependence on the deposition temperatures ranged from room temperature to 35$0^{\circ}C$ regardless of the RF power applied for sputtering the ZnO target. In addition, according to the growth characteristics of the distinguishably different micro-crystal structures and the degree of the c-axis preferred orientation, the deposition temperatures can be divided into 3 temperature regions and 2 critical temperatures in-between. Overall, the ZnO films deposited at/below 20$0^{\circ}C$ are seen to have columnar grains with a highly preferred c-axis orientation where the full width at half maximum (FWHM) of X-ray diffraction rocking curve is 14$^{\circ}$. Based on the experimental findings, several FBAR devices were fabricated and measured. As a result, the FBAR devices show return loss of ~19.5dB at resonant frequency of ~2.05GHz.