• 한국공작기계학회논문집
• /
• 제15권1호
• /
• pp.95-101
• /
• 2006

Minimum weight design of laminated composite panel under combined loading was studied using linear and nonlinear deformation theories and by closed-form analysis and finite difference energy methods. Various buckling load factors are obatined for laminated composite panels with rectangular type longitudinal stiffeners and various longitudinal length to radius ratios, which are made from Carbon/Epoxy USNl25 prepreg and are simply-supported on four edges under combined loading, and then for them, minimum weight design analyses are carried out by the nonlinear search optimizer, ADS. This minimum weight design analyses are constructed with various process such as the simple design process, test simulation process and sensitivity analysis. Subseguently, the buckling mode shapes are obtained by buckling and minimum weight analyses.

• Structural Engineering and Mechanics
• /
• 제28권2호
• /
• pp.189-206
• /
• 2008

In several design codes and specifications, simplified formulae and charts are given for determining the effective lengths of frame columns. It is shown that these formulae may yield rather erroneous results in certain cases. This is due to the fact that, the code formulae utilise only local stiffness distributions. In this paper, a simplified procedure for determining approximate values for the buckling loads of braced frames is developed. The procedure utilises a fictitious load analysis of frames and yields errors less than 10%, which may be considered suitable for design purposes. The proposed procedure is applied to several numerical examples and it is shown that all the errors are in the acceptable range.

• 전산구조공학
• /
• 제11권4호
• /
• pp.209-218
• /
• 1998

고장력강이 구조강재로서 널리 사용되고 있다. 구조물의 극심한 하중을 받게되면 최종강도에 도달할 때까지 좌굴을 동반하게 된다. 그러므로, 고장력강판의 좌굴에 대한 정확한 평가가 중요한 설계기준이 되고 있다. 그러나, 고장력강을 효율적으로 사용하기 위해서는 좌굴허용설계를 도입할 수 있도록 판구조물의 판두께가 얇아져야 한다. 따라서, 박판구조물의 합리적인 설계를 하기 위해서는 좌굴후거동해석이 매우 중요하다. 그러므로, 본 논문에서는 호장증분법을 이용하여 압출하중을 받는 박판구조물의 초기좌굴후거동과 2차좌굴강도에 대하여 규명하였다. 특히, 호장증분법을 좌굴정에서의 하중경로를 추정하기 위하여 적용하였다.

• Steel and Composite Structures
• /
• 제14권5호
• /
• pp.473-491
• /
• 2013

The primary objectives of this paper are to describe the buckling patterns and to determine the squash load of steel plate-concrete (SC) walls. The major variables in this study were the width-thickness (B/t) ratio and yield strength of surface steel plates. Six SC walls were tested, and the results include the maximum strength, buckling pattern of steel plates, strength of headed studs, and behavior of headed studs. Based on the test results, the effects of the B/t ratio on the compressive strength are also discussed. The paper also presents recommended effective length coefficients and discusses the effects of varying the yield strength of the steel plate, and the effects of headed studs on the performance of SC structures based on the test results and analysis.

• Steel and Composite Structures
• /
• 제50권4호
• /
• pp.459-474
• /
• 2024

Classical and first-order nonlocal beam theory are employed in this study to assess the thermal buckling performance of a small-scale conical, cylindrical beam. The beam is constructed from functionally graded (FG) porosity-dependent material and operates under the thermal conditions of the environment. Imperfections within the non-uniform beam vary along both the radius and length direction, with continuous changes in thickness throughout its length. The resulting structure is functionally graded in both radial and axial directions, forming a bi-directional configuration. Utilizing the energy method, governing equations are derived to analyze the thermal stability and buckling characteristics of a nanobeam across different beam theories. Subsequently, the extracted partial differential equations (PDE) are numerically solved using the generalized differential quadratic method (GDQM), providing a comprehensive exploration of the thermal behavior of the system. The detailed discussion of the produced results is based on various applied effective parameters, with a focus on the potential application of nanotubes in enhancing sports bikes performance.

• 한국강구조학회 논문집
• /
• 제16권3호통권70호
• /
• pp.355-363
• /
• 2004

선행연구에서 개발된 개선된 초기형상해석법을 이용하여 케이블지지교량의 초기장력과 보강거더, 주탑의 축방향 압축력을 구하였으며, 이를 이용하여, 케이블 지지교량의 전체 시스템에 대한 좌굴해석을 할 수 있는 프로그램을 개발하였다. 케이블은 트러스요소, 주탑과 보강거더는 보-기둥요소로 모델링하고 대응하는 탄성 및 기하강성행렬을 제시하였다. 초기평형해석을 통하여 얻은 부재력을 이용하여 좌굴파라미터값을 결정하고 이에 대응하는 각 주요부재의 좌굴하중을 산정하고 유효좌굴길이를 구한다. 사장교 및 자정식 현수교에 대하여 결과를 제시하였으며, 결론적으로 이렇게 구한 유효좌굴길이는 축방향력 및 휨모멘트를 동시에 받는 케이블 지지교량의 부재의 안정성 검토에 유용하게 사용될 수 있을 것으로 판단된다.

• Steel and Composite Structures
• /
• 제5권2_3호
• /
• pp.181-192
• /
• 2005

The effective length method for flexural (column) buckling has been used for many decades but its use is somewhat limited in various contemporary design codes to moderately slender structures with elastic critical load factor (${\lambda}_{cr}$) less than 3 to 5. In pace with the use of higher grade steel in recent years, the influence of buckling in axial buckling resistance of a column becomes more important and the over-simplified assumption of effective length factor can lead to an unsafe, an uneconomical or a both unsafe and uneconomical solution when some members are over-designed while key elements are under-designed. Effective length should not normally be taken as the distance between nodes multiplied by an arbitrary factor like 0.85, 1.0, 2.0 etc. Further, the classification of non-sway and sway-sensitive frames makes the conventional design procedure tedious to use and, more importantly, limited to simple regular frames. This paper describes the practical use of second-order analysis with section capacity check allowing for $P-{\delta}$ and $P-{\Delta}$ effects together with member and system imperfections. Most commercial software considers only the $P-{\Delta}$ effect, but not member and frame imperfections nor $P-{\delta}$ effect, and engineers must be very careful in their uses. A verification problem is also given for validation of software for this type of powerful second-order analysis and design. It is a trend for popular and advanced national design codes in using the second-order analysis as a norm for analysis and design of steel structures while linear analysis may only be used in very simple structures.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 봄 학술발표회 논문집
• /
• pp.135-140
• /
• 1998

The buckling of the perforated web of a simply supported Η-section beam subjected to uniformly distributed load is examined by means of the finite element method. With buckling analysis results, the effect of this hole on the load carrying capacity of the beam with dimensions L/h = 11 and 13 ( L = span length h = web depth) is investigated. The parameters whose variation have been considered are hole size and location. It can be generally concluded that the buckling of the perforated web of an H-section beam is not affected seriously by the location of the perforation.

• Steel and Composite Structures
• /
• 제4권4호
• /
• pp.281-301
• /
• 2004

The paper begins by presenting a unified variational approach to the lateral-torsional buckling (LTB) analysis of doubly symmetric prismatic and tapered thin-walled beams with open cross-sections, which accounts for the influence of the pre-buckling deflections. This approach (i) extends the kinematical assumptions usually adopted for prismatic beams, (ii) consistently uses shell membrane theory in general coordinates and (iii) adopts Trefftz's criterion to perform the bifurcation analysis. The proposed formulation is then applied to investigate the influence of the pre-buckling deflections on the LTB behaviour of prismatic and web-tapered I-section simply supported beams and cantilevers. After establishing an interesting analytical result, valid for prismatic members with shear centre loading, several elastic critical moments/loads are presented, discussed and, when possible, also compared with values reported in the literature. These numerical results, which are obtained by means of the Rayleigh-Ritz method, (i) highlight the qualitative differences existing between the LTB behaviours of simply supported beams and cantilevers and (ii) illustrate how the influence of the pre-buckling deflections on LTB is affected by a number of factors, namely ($ii_1$) the minor-to-major inertia ratio, ($ii_2$) the beam length, ($ii_3$) the location of the load point of application and ($ii_4$) the bending moment diagram shape.

• 한국공간구조학회논문집
• /
• 제3권2호
• /
• pp.91-99
• /
• 2003

The purpose of this study is to analyze the characteristics of the connector having an influence on the elasto-plastic buckling load of ball-jointed single layer latticed domes. As an analytic model, domes are composed of tubular member elements, balls and connectors. The joint system of members in single layer latticed domes has influence on the buckling load. Therefore, in this paper, the variation of the elasto-plastic buckling load by effects of the connectors characteristics is analyzed. The structural behavior of the connector is investigated by following points: (1) the length of rigid zone, (2) looseness of screw and (3) the diameter of connector. In addition, the elasto-plastic buckling analysis is carried out through the variation of the connectors section of yielding part, and then the buckling mode of the dome is examined. As a result, it is emphasized that the characteristics of the connector have significant effects on the buckling load of latticed domes.