• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.10
• /
• pp.1157-1162
• /
• 2007

In this paper, E-TDLNN(Expanded-Tapped Delay Line Neural Network) method is suggested to make the model of power amplifier effectively. This method is the one for making the model of power amplifier through the study in neural network to the target value, the measured output spectrum of power amplifier, after adding the external value factor, gate bias, as an invariant input to the TDLNN method which suggested the memory effect of power amplifier effectively. To prove the validity of suggested method, the data at 2 points, 3.45 V and 3.50 V of gate bias range $3.4{\sim}3.6V$ with the 0.01 V step change, are studied and the predicted results at the gate bias 3.40 V, 3.48 V, 3.53 V and 3.60 V shows good coincidence with the measured values.

• The Journal of Churna Manual Medicine for Spine and Nerves
• /
• v.15 no.1
• /
• pp.75-87
• /
• 2020

Objectives : This study aimed to evaluate the effectiveness of manual therapy for wrist pain. Methods : We searched electronic databases (PubMed, Embase, Cochrane, CAJ, KISS, RISS, NDSL, OASIS, and KMBASE) for randomized controlled trials for manual therapy as a treatment for wrist pain. Results : A total of 9 randomized controlled trials were selected and meta-analysis was conducted on 6 studies. Three studies with different design of the intervention/control group were excluded from the meta-analysis. A high risk of bias was observed for both performance bias and detection bias. Conclusions : Our systematic review verified the clinical effect of manual therapy on wrist pain. Based on the results of this study, it is expected that clinical studies on wrist diseases and high-level follow-up studies will be conducted.

• The Korean Journal of Applied Statistics
• /
• v.17 no.1
• /
• pp.61-73
• /
• 2004

Rotation sampling designs may be classified into two categories. The first type uses the same sample unit for the entire life of the survey. The second type uses the sample unit only for a fixed number of times. In both type of designs, the entire sample is partitioned into a finite number(=G) of rotation groups. This paper is generalization of the first type designs. Since the generalized design can be identified by only G rotation groups and recall level 1, we denote this rotation system as l/G rotation design. Under l/G rotation design, variance and mean squared error (MSE) of generalized composite estimator are derived, incorporating two type of biases and exponentially decaying correlation pattern. Compromising MSE's of some selected l/G designs, we investigate design efficiency, design gap effect, ans the effects of correlation and bias.

• Journal of the Korean Society of Costume
• /
• v.33
• /
• pp.217-228
• /
• 1997

The purpose of this study was to investigate influence of the construction method of the circular skirt on drapability and shape of static silhouette and length variation. In made 24 types of skirts giving the variations (six kinds of peach skin-like finished fabrics two types of cutting method two types of machine stitch method of hem), The results were as follows: 1. Analysis of drapability In the cutting method thre was similarity between warp direction and true bias direc-tion. In the machine stitch method of hem there was similarity between blind stitch and blind stitch machine. According to the fabrics analysis of drapability was excellent in the order N/P 80/20(fabric 1)>P 100(fabric 5)>P 100(fabric 6)>P 100 (fabric 2)>P 100 (fabric 4)>N/C 50/50(fabric 3). 2. Analysis of the characteristics values of static silhouette shape In the cutting method shape of static sil-houette became wide in the warp direction. In the machine stitch method of hem shape of static silhouette became wide in the blind stitch. According to the fabrics shape of static silhouette became most wide in the N/C 50/50(fabric 3) and shape of static sil-houette become most narrow in the P 100(fabric 2,5) 3. Analysis of the length variation In the cutting method the true bias direc-tion was longer than the warp direction. In the machine stitch method of hem there was simi-machine stitch method of hem there was simi-larity between blind stitch and blind stitch ma-chine. In fabrics the P 100(fabric 6) showed the longest the N/C 50/50(fabric 3) showed most slight. Interaction between the cutting and messure-ment part of skirt lengh. In the warp diretion parts that showed longest length variation were C. G, K, O in the true bias diretion parts that showed most slight length variation were A, E, M, I.

• Atmosphere
• /
• v.16 no.3
• /
• pp.203-213
• /
• 2006

The objective of this paper is to investigate the effects of physical parameterization on the simulation of a snowfall event over Korea caused by air-mass transformation by using the PSU/NCAR MM5. A heavy snowfall event over Korea during 3-5 January 2003 is selected. In addition to the control experiments employing simple-ice microphysics scheme, MRF PBL scheme, and original surface layer process, three consequent physics sensitivity experiments are performed. Each experiment exchanges microphysics (Reisner Graupel), boundary layer (YSU PBL) schemes, and revised surface layer process with a reduced thermal roughness length for the control run. The control run reproduces an overall pattern of snowfall over Korea, but with a high bias by a factor of about 2. As revealed in the previous studies, the cloud microphysics and PBL parameterizations do not show a significant sensitivity for the case of snowfall. A more sophisticated cloud processes does not reveal a discernible effect on the simulated snowfall. Further, high bias in snowfall is exaggerated when a more realistic PBL scheme is employed. On the other hand, it is found that the revised surface layer process plays a role in improving the prediction of snowfall by reducing it. Thus, it is found that a realistic design of surface layer physics in mesoscale models is an important factor to the reduction of systematic bias of the snowfall over Korea that is caused by air-mass transformation over the Yellow sea.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.636-644
• /
• 1997

The effect of various processing parameters, in particular the substrate and filament temperature, on the nucleation of diamond has been studied for the hot filament CVD process with a negative bias on the substrate. As far as the substrate temperature was maintained around the critical temperature of 73$0^{\circ}C$, the nucleation of diamond increased with increasing filament temperature. The maximum nucleation density of ~ 2$\times$109/$\textrm{cm}^2$ was obtained under the condition of filament temperature of 230$0^{\circ}C$, substrate temperature of 75$0^{\circ}C$, bias voltage of 300V, methane concentration of 20%, and deposition time of 2 hours. This nucleation density is about the same as those obtained in previous investigations. For fixed substrate temperatures, the nucleation density varies up to about 103 times depending on experimental conditions. This result is different from that of Reinke, et al. When the substrate temperature was above 80$0^{\circ}C$, a silkworm~shaped carbon phase was co-deposited with hemispherical microcrystalline diamond, and its amount increased with increasing substrate temperature. The Raman spectrum of the silkworm-shaped carbon was the same as that of graphitic soot. The silkworm-shaped carbon was etched and disappeared under the same as that of graphitic soot. The silkworm-shaped carbon was etched and disappeared under the deposition condition of diamond, implying that it did not affect the nucleation of diamond.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.3
• /
• pp.179-187
• /
• 2008

In this paper, we carried out the performance evaluation of depolarized fiber optic gyroscope(D-FOG) that was designed and fabricated with the low-cost optical communication single mode fiber and depolarizer. In order to reduce the phase error of D-FOG, the circuit of stabilized current and temperature of the light source was made and the performance was analyzed. The current and the temperature stability of the fabricated stabilization circuit were less than $200{\mu}A$ and $0.0098^{\circ}C$, respectively. Also, the D-FOG's experimental result showed that the value of the dynamic range of rotated rate, the scale factor error with a good linearity, and the zero bias drift were ${\pm}50^{\circ}/s$, 2.8881%, and $19.49^{\circ}/h$, respectively. The results indicated that a low-cost FOG was able to fabricate which was more cost effective than conventional FOG with a high-cost high-birefringent polarization maintaining fiber.

• Journal of Forest and Environmental Science
• /
• v.13 no.1
• /
• pp.81-89
• /
• 1997

Urban river needs continuous observation for the river conservation because river surrounding environment sensitivly is changed by human activity. In order to grasp the effect of human activity against Taebaek river in Chunchon city, this research analysed the channel shape change, fluctuation volume and bias degree over five times, for June, 1993 to June, 1996. The results were as follows : 1. The change of channel shape on each surveying time mainly occurred in June, 1996 and maximum deposition. $1,247m^3$ occurred on 19~20 section, maximum scouring, $340m^3$ occurred on 6~7 section, 2. When comparing with June, 1993, increased deposition volume of channelbed was about $4,600m^3$ in June, 1996, 3. The bias degree of channel mainly occurred in June, 1996 of surveying times and at 6, 7, 15, 16, 17, 18, 19, 20 line of surveying lines.

• Journal of the Korean Ceramic Society
• /
• v.54 no.6
• /
• pp.511-517
• /
• 2017

With different working pressures and substrate biases, Cr-Al-N coatings were deposited by hybrid physical vapor deposition (PVD) method, consisting of unbalanced magnetron (UBM) sputtering and arc ion plating (AIP) processes. Cr and Al targets were used for the arc ion plating and the sputtering process, respectively. Phase analysis, and composition, binding energy, and microstructural analyses were performed using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and field emission scanning electron microscopy (FESEM), respectively. Surface droplet size of Cr-Al-N coatings was found to decrease with increasing substrate bias. A decrease of the deposition rate of Cr-Al-N films was expected due to the increase of substrate bias. The coatings were grown with textured CrN phase and (111), (200), and (220) planes. X-ray diffraction data show that all Cr-Al-N coatings shifted to lower diffraction angles due to the addition of Al. The XPS results were used to determine the $Cr_2N$, CrN, and (Cr,Al)N binding energies. The compositions of the Cr-Al-N films were measured by XPS to be Cr 23.2~36.9 at%, Al 30.1~40.3 at%, and N 31.3~38.6 at%.

• Journal of The Korean Association For Science Education
• /
• v.22 no.2
• /
• pp.314-335
• /
• 2002

The purpose of this study was to investigate the effects of students' prior knowledge on scientific reasoning process performing a task of controlling variables with computer simulation and to identify a number of problems that students encounter in scientific discovery. Subjects for this study included 60 Korean students: 27 fifth-grade students from an elementary school; 33 seventh-grade students from a middle school. The sinking objects task involving multivariable causal inference was used. The task was presented as computer simulation. The fifth and seventh-grade students participated individually. A subject was interviewed individually while the investigating a scientific reasoning task. Interviews were videotaped for subsequent analysis. The results of this study indicated that students' prior knowledge had a strong effect on students' experimental intent; the majority of participants focused largely on demonstrating their prior knowledge or their current hypothesis. In addition, studnets' theories that were part of one's prior knowledge had significant impact on formulating hypotheses, testing hypothesis, evaluating evidence, and revising hypothesis. This study suggested that students' performance was characterized by tendencies to generate uninformative experiments, to make conclusion based on inconclusive or insufficient evidence, to ignore, reject, or reinterpret data inconsistent with their prior knowledge, to focus on causal factors and ignore noncausal factors, to have difficulty disconfirming prior knowledge, to have confirmation bias and inference bias (anchoring bias).