• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.244-247
• /
• 2001

Lubricanting characteristics in the warm forging have influence on forgeability of products. but Research on deformation characteristic of warm forging on the lubricant and lubricating method lack. This paper deform a bevel gear by warm forging and evaluate deformation loads and quality of products by each lubricants and lubricating method using oil-based lubricants(Soy, Oildag) and water-based lubricants(Deltaforge $\#31$, Renite S-26-X, Deltaglaze $\#151$). In conclusion, the less a deformation load by lubricants the more improvement a quality of product in manufacture of a bevel gear and water-based lubricants in the warm forging reduce a deformation load and improve a quality of products. Especially, Deltaforge $\31$ have excellent characteristic in the warm forging.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.43-46
• /
• 2003

To develop bevel gear dies that have characteristics of high precision and enough life time, the technology of die manufacturing and design which increase the resistance of wear and fatigue is essentially needed. Here in the study, we have investigated several materials for dies and electrode. And, the most economical and suitable electrode material has been selected through the characteristic analysis of electrode materials such as copper, graphite and chromium copper. With the help of CAD/CAM/CAE, the total manufacturing system of high precision electrode for bevel gear has been established.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.2
• /
• pp.42-48
• /
• 1997

Drive systems are composed of spiral bevel gear, axle and bearings. In this paper, drive systems and the part of them are analyzed and a correlation of the factor that shows the geometry of spiral bevel gear is evaluated. The Weibull distribution of probability for survival, which caused by the load of bearings and gear teeth, would be calculated, and the life and reliability with equivalent function could be measured more specifically. The reliability methods are applied as a probability of which the gear drive systems are satisfiably operated.

• Journal of Welding and Joining
• /
• v.15 no.2
• /
• pp.64-71
• /
• 1997

In order to define the effects on shapes of welding joint, during Post Welding Heat Treatment (PWHT), we have carried out numerical analysis on the several test pieces by using computer program which was based on thermal-elasto-plastic-creep theories for the study. And then, welding residual stresses after PWHT were measured same test-pieces to compare with the results of numerical analysis. The main results obtained from this study is as follows: 1) The distribution modes of welding residual stresses are same on the all test pieces after and during PWHT by the both sides (measurement and numerical analysis). 2) The mechanical difference for change the thickness of plate and bevel angle are not appeared. 3) In a mechanical point of view (like material quality test, welding deformation etc.), manimum bevel angle (40$^{\circ}$.) is more suitable than maximum bevel angle (70$^{\circ}$).

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.11a
• /
• pp.209-210
• /
• 2007

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.176.1-176.1
• /
• 2005

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.927-928
• /
• 2010

• Journal of Advanced Marine Engineering and Technology
• /
• v.14 no.1
• /
• pp.72-82
• /
• 1990

It is impossible to directly analyse stress distribution on thin bevel Gear. On this Paper, the author propose a method to analyse the stress of thin bevel gear boundary element method and develope a computer program. The propriety of this program is verified by comparing the numerical calculating results with theoretical results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.873-874
• /
• 2011

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.26 no.4
• /
• pp.395-401
• /
• 2017

Energy absorption capabilities and failure modes of circular tubes made of glass/epoxy with two trigger mechanisms were evaluated. Three types of glass/epoxy tubes were fabricated using a hand lay-up method with unidirectional and woven fabric prepregs tapes, and a filament winding method. The one end of the fabricated tubes was machined for the bevel trigger and tulip trigger. Then, crush tests were conducted at 10 mm/min loading speed, wherein the glass/epoxy tubes were crushed by a brittle fracturing mode combined with fragmentation and lamina-splaying modes. The UD glass/epoxy tubes with a bevel trigger and the filament winded tubes with a tulip trigger showed the maximum and minimum specific energy absorptions, respectively, with a difference of 9.3%. The tube with a tulip trigger exhibited a maximum reduction of 5.7% in the initial peak load; the tube with a bevel trigger showed a maximum increase of 2.9% in the specific energy absorption.