• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2004.11a
• /
• pp.3-4
• /
• 2004

A flexible Packaging scheme, which embedded chip packaging, has been developed using a thinned silicon chip. Mechanical characteristics of thinned silicon chips are examined by bending test and finite element analysis. Thinned silicon chips ($t<50{\mu}m$) are fabricated by chemical etching process to avoid possible surface damages on them. These technologies can be use for a real-time monitoring of blood pressure. Our research targets are implantable blood pressure sensor and its telemetric measurement. By winding round the coronary arteries, we can measure the blood pressure by capacitance variation of blood vessel.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1078-1082
• /
• 2003

A feasibility study for the fabrication of master replication with nanostructures by Nanoimprint Lithography (NIL) was investigated for application of polymer Photonic Bandgap (PBG) devices used in photonic IC. Large area gratings of $9{\times}15(mm^2)$ with p = 400 nm was successfully embossed on PMMA on silicon wafer and the embossing parameters (temperature, pressure, time) were established. A precise control of $O_2$ plasma Reactive Ion Etching (RIE) process time allowed window opening over the whole area despite the presence of wafer bending. Master replication with aspect ratio 1 was successfully fabricated, but master replication with aspect ratio 3 needs to optimize parameters. All replications were done in a NIL process.

• Structural Monitoring and Maintenance
• /
• v.3 no.2
• /
• pp.145-155
• /
• 2016

The Pulse-Pre Pump Brillouin Optical Time Domain Analysis (PPP-BOTDA) technique is introduced to implement the multi-direction strain measurement. The monitoring principle is stated. The layout scheme of optical fibers is proposed. The temperature compensation formula and its realizing method are given. The experiments, under tensile load, combined bending and tensile load, are implemented to validate the feasibility of the proposed method. It is shown that the PPP-BOTDA technique can be used to discriminate the multi-direction strains with high spatial resolution and precision.

• Structural Engineering and Mechanics
• /
• v.46 no.6
• /
• pp.843-852
• /
• 2013

This paper presents results of the effect of different bolt tightening sequences and methods on the performance of gasketed bolted flange joint using nonlinear finite element analysis. Bolt preload scatter due to elastic interactions, flange stress variation and bolt bending due to flange rotation and gasket contact stress variation is difficult to eliminate in torque control method i.e. tightening one bolt at a time. Although stretch control method (tightening more than one bolt at time) eradicates the bolt preload scatter, flange stress variation is relatively high. Flange joint's performance is compared to establish relative merits and demerits of both the methods and different bolt tightening sequences.

• Journal of Welding and Joining
• /
• v.22 no.2
• /
• pp.46-50
• /
• 2004

In today's highly competitive marketplace, it is of great significance for the manufacturing industry to reduce lead-time and costs fur the product development. Since first emerged in 1986, Rapid Prototyping (RP) technology has helped successfully to reduce time and costs. Recently, RP using functional materials such as metal has been researched. However RP using the molten metal has been struggling to resolve several drawbacks, such as dimensional inaccuracy, poor surface finish, post finishing, etc., that originate primarily from the overall deposition of molten metal for each layer. So, the purpose of this study is to develop a new RP technique using sheet metal and projection welding for reducing several drawbacks in occurring RP using molten metal. Also tensile and bending specimens were made by the developed RP process using projection welding and were verified.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.5
• /
• pp.425-429
• /
• 2007

A linear ultrasonic motor was designed by a combination of the longitudinal and bending mode. linear ultrasonic motors are based on an elliptical motion on the surface of elastic body, such as bar or plates. The corresponding eigen-mode of one resonance frequency can be excited twice at the same time with a phase shift of 90 degrees in space and time. That is excite symmetric and anti-symmetric modes. Then it determines the thrust and speed of the motor. Linear ultrasonic motors are investigated experimentally in according to be fabricated a general classification to motor structure and material characteristic. There was the first to simulate as use of finite element analysis ANSYS 9.0. The AL-T2W8-ARM14-LEG18-ANGLE80 motor has a maxim efficiency 18 % under the speed 0.14 m/s, thrust 345 gf and preload 280 gf, operating frequency is 57.6 kHz.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.1
• /
• pp.50-55
• /
• 1997

This study was carried out to utilize old newspaper(ONP) and paper sludge more effectively, and also to elucidate the influences of pressing conditions on the medium density fiberboard(MDF) properties. MDFs were made from ONP and low grade of paper sludge by wet process with change of pressing time, temperature and pressure. MDFs of ONP were more affected by pressing conditions, especially pressing pressure, but temperature and pressing time were also important. According to mixing paper sludge to ONP tensile and bending strength of MDF were decreased, but density and dimensional stability were improved. These results indicated that some physical properties of MDF can be improved by paper sludge and it is possible to use it in MDF.

• Steel and Composite Structures
• /
• v.34 no.4
• /
• pp.581-597
• /
• 2020

Light-Weight Concrete containing Expanded Poly-Styrene Beads (EPS-LWC) is an approved structural and non-structural material characterized by a considerably lower density and higher structural efficiency, compared to concrete containing ordinary aggregates. The experimental campaign carried out in this project provides new information on the mechanical properties of structural EPS-LWC, with reference to the strength and tension (by splitting and in bending), the modulus of elasticity, the stress-strain curve in unconfined compression, the absorbed energy under compression and reinforcement-concrete bond. The properties measured at seven ages since casting, from 3 days to 91 days, in order to investigate their in-time evolution. Mathematical relationships are formulated as well, between the previous properties and time, since casting. The dependence of the compressive strength on the other mechanical properties of EPS-LWC is also described through an empirical relationship, which is shown to fit satisfactorily the experimental results.

• Textile Coloration and Finishing
• /
• v.16 no.1
• /
• pp.59-64
• /
• 2004

As a simulation of solvent-assisted dyeing, the solvent effects on the structure of polyethylene terephthalate(PET) film treated by dimethylformamide(DMF) were investigated. The effects were evaluated by the atomic force microscopy(AFM) topographical changes and FT-IR spectrum analysis. PET films treated with DMF at $70^{\circ}C$ for several different treatment time(20, 40, and 60 min). AFM topography showed that, with increasing treatment time by DMF, PET surfaces became smooth due to the swelling phenomenon and the rigid structure changed into flexible state which was contributed to increase the surface area of PET films. FT-IR spectrum analysis showed that DMF and molecular chains of PET interacted each other via their polar carbonyl groups and that DMF also affected the out-of-plane bending vibration mode of phenyl ring of PET.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.151-162
• /
• 2000

This study is concerned with computerized multi-level substructuring methods and stress analysis of coil springs. The purpose of substructuring methods is to reduce computing time and capacity of computer memory by multiple level reduction of the degrees of freedom in large size problems that are modeled by three dimensional continuum finite elements. In this paper, the spring super element developed is investigated with tension, torsion, and bending of a cylindrical bar in order to verify its accuracy and efficiency for the multi-level substructuring method. And then the algorithm is applied to finite element analysis of coil springs. The result demonstrates the validity of the multi-level substructuring method and the efficiency in computing time and memory by providing good computational results in coil spring analysis.