• Tribology and Lubricants
• /
• v.26 no.5
• /
• pp.283-290
• /
• 2010

In this study, the stiffness and damping coefficients of herringbone grooved air journal bearings are studied. A generalized coordinate transformation method to handle the complex geometry of incompressible fluid bearing is modified for compressible fluid. The modified equations are discretized by the base of finite difference method. A new computer program using Visual C++ language is developed. The load carrying capacity and stiffness and damping coefficients are calculated according to the design parameters like groove depth or the number of grooves and compared to that of plain air journal bearings.

• The KSFM Journal of Fluid Machinery
• /
• v.2 no.2 s.3
• /
• pp.27-31
• /
• 1999

This paper describes the shaft vibration phenomena measured on a pump-turbine of a pumped storage power plant. The pump-turbine runs at a rotational speed of 450 rpm (7.5 Hz). The power output (load) of the pump-turbine is varied from 100 to 300 MW in the generating mode. The magnitude of the shaft vibration highly depends on the power load. The vibration magnitude of the shaft is very high in the middle load zone from 170 to 210 MW, elsewhere the vibration is low. From nitration spectra, it is shown that the frequency of major nitration in that load zone is 2.5 Hz which is approximately $34\%$ of the shaft rotating speed in Hz. This frequency component does not occur below and above that load zone. This subsynchronous vibration is caused by the flow induced disturbance due to spiral vortex flow downstream of the pump-turbine runner. Furthermore, the shaft vibration is highly decreased due to an increased bearing preload.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.8
• /
• pp.1940-1950
• /
• 1993

The theoretical investigation is done on the dynamic behavior of a crank shaft used in a scroll compressor. The compression performance of a scroll compressor is directly influenced by the sealing characteristics between fixed and orbiting scrolls, which is related with the dynamic behavior of a scroll compressor. Analyzing the constrained power transmitting system is came to be of importance, accordingly. The equations of motion and interacting forces of a scroll compressor are derived and solved numerically in this paper. The locus of the crank shaft is also obtained by employing the reaction force caused by the oil film of journal bearing. The results show that the crank shaft of a scroll compressor has considerably stable rotating locus.

• 유체기계공업학회:학술대회논문집
• /
• 1998.12a
• /
• pp.166-172
• /
• 1998

This paper describes the shaft vibration phenomena measured on a pump-turbine ofa pumped storage power plant. The pump-turbine runs at a rotational speed of 450 rpm (7.5 Hz). The power output (load) of the pump-turbine was varied from 100 to 300 MW in the generating mode. It was found that the magnitude of the shaft vibration was highly dependent upon the power load. The vibration magnitude of the shaft vibration is very high in the middle load zone from 170 to 210 MW, elsewhere the vibration low. From vibration spectra, it was found that the frequency of major vibration in that load zone was 2.5 Hz which is approximately $34\%$ of the shaft rotating speed in Hz. This frequency component disappeared below and above that load zone. This subsynchronous vibration is caused by the flow induced disturbance due to spiral vortex flow downstream of the pump-turbine runner. Furthermore, it was found that shaft vibration was highly decreased due to the increase of bearing preload.

• Proceedings of the KIEE Conference
• /
• 2007.04c
• /
• pp.5-7
• /
• 2007

This paper deals with design and analysis of thrust magnetic bearing for 300HP class high speed motor. Using the solutions obtained from equivalent magnetic circuits, we predicts the electromagnetic characteristics such as thrust, time constant and power loss according to design parameters. And then, using non-linear finite element analysis, a detailed design is performed considering saturation in order to meet requirements.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.9
• /
• pp.1391-1399
• /
• 2001

The AE measurement is one of the most convenient methods for detecting contacts between the slider and the disk. The AE method has been widely used in the investigation of the tribology of sliding interfaces due to its convenience. We examined the relationship between the AE signal and the flying height of a slider. We investigated the influence of the disk linear velocity on the AE rms signal by using the AE measurement system. The experiment also gives the relationship between the take-off velocity and the disk surface conditions. To investigate the behavior of the slider further, the variances of the AE signals are analyzed. The experimental results indicate that the increase in the magnitude of the AE rms signal does not necessarily mean the slider/disk contacts.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.121-126
• /
• 1993

Tiling pad journal bearing that has high stability is analyzed about air-lubricated bearing that is usually used to need high precision by using the Direct analysis. The pressure that supports the shaft is occured by the differences between the shaft and pads radii of curvatures. So the characteristics of load capacity for their variable values is important. In this paper the load capacity is compared with some the eccentricity ratio values of0.1, 0.2, 0.5, 0.8. The large load capacity comes from large eccentricity ratio, highbearing number and high preload. But if the preload become high too much, then the shaft makes contact with pads.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.1
• /
• pp.47-52
• /
• 2005

In this paper, the effect of TiN-coating on product quality such as dimensional accuracy and surface roughness is experimentally investigated. A punch of SKD11 material in cold forging an automotive bearing shaft and its related process found in a cold forging company are selected as the test example. The effect of TiN-coating is revealed in a quantitative manner. It is to be noted that TiN-coating is effective in controlling the dimensional accuracy and surface roughness as well as in increasing tool lift.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.7
• /
• pp.94-100
• /
• 1999

This study adopted the ultra precision machining system which was composed of an air bearing spindle, a granite bed, air pad and a linear feeding mechanism. It also applied the cutting experiment on the aluminum alloy. To evaluate the safety of high speed machining, we examined the surface roughness according to the changes of cutting speed and obtained the speed limit. This paper also studied the effect of cutting condition such as feed rates and depths of cut on the surface roughness within the speed limit. This provided practical information regarding ultra precision machining.

• Rapid Communication in Photoscience
• /
• v.3 no.4
• /
• pp.85-87
• /
• 2014

We studied the characteristics of emissive state of the first (p-G1) and second (p-G2) generation of phenylacetylene dendrimers bearing stilbene as a core by using time-resolved fluorescence spectroscopy in cyclohexane (c-Hex) and N, N-dimethylformide (DMF), which are nonpolar and polar solvents, respectively. Time-dependent red-shift of emission spectra p-G2 both in c-Hex and DMF was observed in comparison with p-G1. Besides, the time constant of red-shift of spectra was found to be larger in DMF than in c-Hex. This indicates that the emissive state of p-G2 has a polar character in DMF as a result of charge delocalization from core to peripheral dendrons followed by stabilization of emissive state.