• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 가을 학술발표회 논문집
• /
• pp.382-389
• /
• 2002

Recently, auger-drilled piling has been widely used in urban area to reduce the air pollution and noise. But this construction method that its basic theory was introduced from Japan may be changed depending on the each piling company and construction field condition. Therefore, the design code and management method for auger-drilled piling is not defined yet. Especially, the lack of research on the bearing capacity of auger-drilled piling leads to the absence of rational bearing capacity prediction equation. This paper presents the optimum design code and economical construction method of the auger-drilled piling by proposing the new bearing capacity prediction equation based on the site specific soil types and construction conditions. In this paper, existing bearing capacity prediction equations and current pile load tests were compared. And the end bearing capacity and skin friction characteristics were also analyzed by comparing the results of CAPWAP. From the results of analysis, a reliable bearing capacity prediction equation considered soil types is proposed.

• 한국지반신소재학회논문집
• /
• 제6권1호
• /
• pp.1-7
• /
• 2007

연약지반처리를 위해 바로 장비가 진입하기 어려운 경우에, 적절한 강도를 갖는 토목섬유를 부설하고 그 위에 샌드매트층(Sand Mat)을 형성시켜 기초지반의 지지력을 증가시킨다. 이러한 보강메카니즘에 대한 지지력을 평가하는 식을 Yamanouchi(1985)가 제안을 하였다. 우리나라의 경우 주로 Yamanouchi가 제안한 식을 사용하여 설계를 행하고 있다. 그러나, 제안식에서 접지압을 감소시킬 목적으로 접지폭원을 증대시키면 오히려 지지력은 감소하고 소정의 안전율을 얻기 위해서는 성토두께를 증가해야 하는 등 지지력 산정에 있어서 논리적인 모순점을 내포하고 있다. 이러한 논리적인 모순점을 검토하기 위해서 모형토조에 연약지반을 조성하여 지지력실험을 실시하였다. 연약지반자체, 연약지반위에 보강재를 포설했을 때, 포설된 보강재에 인위적으로 인장력을 가했을 경우, 샌드매트층을 포설했을 때, 다른 조건을 일치시키며 단지 재하판의 폭을 달리 했을 때 등으로 나누어 모형재하시험을 행하였다. 실험결과를 다양하게 분석하였으며 특히 Yamanouchi가 제안한 식이 갖는 모순점을 설명하는 새로운 지지력식을 제안하였다.

• 기술발표회
• /
• 통권2006호
• /
• pp.320-328
• /
• 2006

In this test, there was two dimensional model loading test implemented for analysis with respect to the problem of evaluating bearing capacity and the application range on the dredged and reclaimed ground. It was got following conclusion through comparison of button's and Brown&Meyerhof"s equation with experimental result that was obtained by 2 dimensions model loading test. For the difference between average undrained shear strength by 2/3B of loading board width and under 2/3B is more than ${\pm}$ 50%, application of Nc(coefficient of bearing capacity was used in that case $\phi$=0 analysis is considered in the single layer) was declined. Brown&Meyerhof(1969)'s equation was underestimated comparing with loading test result, while Button(1953)'s equation was overestimated comparing with loading test result applied dividing as double layers of upper dessication layer and lower soft layer about dredged and reclaimed ground. Also, bearing capacity factors, Nc that was calculated by using button's equation was estimated greatly about 1.7 times more than bearing capacity factors, Nc that was calculated by using Brown&Meyerhof's equation. Bearing capacity factors, Nc that was calcuated by using Brown&Meyerhof's and Button's equation was evaluated each 2.3-3.6 times, 1.3-2.1 times smaller than bearing capacity factors, Nc5.14 that was calcuated by using Meyerhof's equation in case of unit layer.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 가을 학술논문 발표대회
• /
• pp.133-134
• /
• 2020

The equation of end bearing capacity is applied differently depending on the type of pile, construction method, and load characteristics considering the construction standards. The bearing capacity equation of the design standard is presented in various ways according to the design conditions such as construction method and ground condition, etc. but, It does not reflect the ground strength according to the SPT-N value of weathered rock. This study analyzed the trend of allowable tip bearing capacity by pile diameter through about 480 dynamic loading tests conducted for the construction/quality management of piles for the last 6 years since 2015. The equation for the ultimate end bearing capacity per unit area according to the SPT-N value is presented. The proposed formula of ultimate end bearing capacity per unit area can be applied in the range of 15,000kN/m2 to 30,000kN/m2. The proposed formula, which complements the existing formula, enables pile design and construction/quality management.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.1172-1177
• /
• 2008

The best way to gain optimal results on the bearing capacity is to perform the plate bearing test on field but it is not always possible. In the case of not performing the bearing test but estimating bearing capacity equations, it is not yet determined what equation is appliable. In this paper the results of bearing capacity equation and the loading tests of 12 samples were compared and what the one is more reliable than others was verified. The comparison showed that the range of the values using Hansen's equation was 0.67 and 1.44 times of the measured, that of Vesic's was 0.71 and 1.27, that of Meyerhof is 0.69 and 1.1, and that of Terzaghi was 0.87 and 1.57.

• 한국지반공학회논문집
• /
• 제37권7호
• /
• pp.25-34
• /
• 2021

연약지반으로 이루어진 준설매립부지는 지반이 매우 연약한 상태이기 때문에 설계시 정확한 지지력을 계산하는 것은 어렵고 복잡한 요인들이 고려되어야 한다. 최근까지 준설매립지를 대상으로 다양한 연약지반처리공법을 설계하고 있지만, 초기 장비진입을 위해서 기존 Meyerhof(1974) 복합토층 지지력 계산으로 안전율을 예측하고 있다. 기존 방정식들은 시공성 안전을 확보한다는 차원에서 연약지반 지지력을 과소평가하여 경제적 비용이 증가될 수 있다. 따라서 본 연구에서는 현장여건이 고려된 지지력 식을 제안하였다. 이를 위하여 이론적인 방정식에서 고려되지 못하는 토목섬유의 봉합사 역할과 봉합인장강도가 지지력에 끼치는 영향을 실험으로 제시하여 적절한 연약지반 지지력을 평가할 수 있도록 제시하였다. 그리고, 현장시험으로 수정방정식 지지력의 안정성이 평판재하시험으로 실측한 값과 비교하여 적절성을 확인하였다. 향후 준설토 매립지반의 설계와 시공시 본 연구 결과가 기초자료로 활용될 것으로 판단된다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.401-414
• /
• 2010

Top Base Foundation(TBF) is a stabilization method for light weight structures particularly in the soft ground. It is widely used for the increment of bearing capacity and restraining settlement of foundations when the bearing capacity of ground is not enough. However, when the design values from exiting Japanese standard are compared with the observation values from the field measurement, the bearing capacity of exiting standard estimated smaller For this reason, it is necessary to establish more reasonable prediction technique considering to understand the behavior of TBF in soft ground. In this study, 1/5 scale model tests were performed in the laboratory. Also, full scale tests were carried out in order to investigate the behavior of TBF with various shapes. In addition, about 100 sites measurement data were evaluated to investigate the behavior of TBF in various ground conditions. Based on the results of the model tests and field measurement data, it was possible to establish more reasonable the bearing capacity equation of TBF considering various N-value of soil, the effect of underground water and failure shapes.

• Tribology and Lubricants
• /
• 제18권3호
• /
• pp.181-186
• /
• 2002

A numerical analysis is undertaken to show the influence of bearing design parameters on the load capacity of air lubricated spiral grooved thrust bearing. The governing equation derived from the mass balance is solved by the finite difference method. Optimal values for various design parameters are obtained to maximize the load capacity. The design parameters are the groove angle, the groove width ratio, the groove height ratio, and the seal ratio.

• Tribology and Lubricants
• /
• 제30권5호
• /
• pp.284-290
• /
• 2014

The influence of round embossed surface on slider bearing characteristics and its load carrying capacity is discussed for thin film effect of embossed slider bearing. For the numerical computation of lubrication parameters such as pressure, load capacity and shear stress that are normalized and a Reynolds equation is used for the analysis of embossed slider bearing characteristics. For this purpose, the finite difference method of central difference scheme is used in this study. In a slider bearing with embossed form, several simulation parameters such as pressure, load capacity and shear stress of the bearing can be obtained according to independent parameters such as the slope of the slider bearing and number of embossing in the upper slider. Also this results can be summarized and be stored in sequential data file for latter analysis. After all, their distribution of the pressure and shear stress parameters can be displayed and be analyzed easily by using the developed program with matlab GUI technique. The independent parameters such as a number of embossing and a slope of the embossed surface slider are used for discussing simulation parameters of pressure distribution, shear stress and load carrying capacity of the round embossing. These study results reported in this paper should be applied to the other shaped slider bearing with a rectangular embossed surface or rectangular waved surface.

• 한국기계가공학회지
• /
• 제13권5호
• /
• pp.35-42
• /
• 2014

The influence of sine wave striated surface roughness on load carrying capacity of a bearing is studied for thin film effect of slider bearing. A Reynolds equation appropriate for slider bearing is used in this paper for analysis and it is discussed using finite difference method of central difference scheme. For a slider bearing with sine wave simple roughness form, several parameters such as pressure, load capacity and shear stress of the bearing can be obtained and also this results can be stored in sequential data file for latter analysis. After all, their distribution can be displayed and analyzed easily by using the matlab GUI technique. The parameters such as amplitude, number of waviness and slope of the surface are used for discussing the load carrying capacity of the rectangular bearing. The results reported in this paper should be applied to the other slider bearing such as rectangular or round embossed surface of slider bearing.