• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.1071-1074
• /
• 2002

This paper presents Bi thin films have been fabricated by atomic layer-by-layer deposition and co-deposition at an IBS method. The growth rates of the films was set in the region from 0.17 to 0.27 nm/min. MgO(100) was used as a substrate. In order to appreciate stable existing region of Bi 2212 phase with temperature and ozone pressure, the substrate temperature was varied between 655 and $820^{\circ}C$ and the highly condensed ozone gas pressure$(PO_3)$ in vacuum chamber was varied between $2.0{\times}10^{-6}$ and $2.3{\times}10^{-5}Torr$. Bi 2212 phase appeared in the temperature range of 750 and $795^{\circ}C$: and single phase of Bi 2201 existed in the lower region than $785^{\circ}C$. Whereas, $PO_3$ dependance on structural formation was scarcely observed regardless of the pressure variation. And high quality of c-axis oriented Bi 2212 thin film with $T_c$(onset) of about 90 K and $T_c$(zero) of about 45 K is obtained. Only a small amount of CuO in some films was observed as impurity, and no impurity phase such as $CaCuO_2$ was observed in all of the obtained films.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10a
• /
• pp.601-608
• /
• 2000

Steel fiber and Polymer are used widely for the reinforcement material of RC structures because of its excellence of durability, serviceability as well as mechanical properties. Polymer-Steel fibrous high strength concrete beam's input ratio are 1.0%. The shear span-to-depth ratio are 1.5, 2.8 and 3.6, compressive strength of specimens 320kg/㎠, 436kgf/㎠ and 520kgf/㎠ in 28 days. The static test was carried out to measure the ultimate load, the initial load of flexural crack and of diagonal crack, from which crack patte군 and fracture modes are earned. Also, stress-strain, load-strain and load-deflection are examined during the test cracks(shear crack, flexural crack, and diagonal tension crack), when the load values are sketched according to the growth of crack. Result are as follows; (1) The failure modes of the specimens increase in rigidity and durability in accordance with the increase of mixing steel fiber and polymer. (2) The load of initial crack was the same as the theory of shear-crack strength (3) Polymer-Steel fibrous high strength concrete beams have increased the deflection and strain at failure load, improving the brittleness of the high strength concrete. (4) In this result of study, an additional study need to make a need formular because the study is different from ACI formular and Zsutty formular.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.2
• /
• pp.391-401
• /
• 1995

Several tests of the Double Cantilever Beam(DCB) were carried out for influence of the fiber orientation on the Mode I of the interlaminar fracture behavior in the Carbon/Epoxy composites. The interlaminar fracture toughness of Mode I was estimated based on the energy release rate of Mode I, $G_{I}$. The fracture toughness at crack initiation, $G_{IC}$, increases from type A to type E. The fracture toughness, $G_{IR}$ , is almost constant macroscopically for type A and type E when crack propagates. $G_{IR}$ for types B, C, D increases rapidly at the beginning of the crack growth then it decreases gradually. The fracture surface observation by SEM was also obtained the same results. Consequently the influence of the fiber orientation on the Mode I Interlaminar fracture behavior was made clear.ear.

• Computers and Concrete
• /
• v.25 no.3
• /
• pp.205-214
• /
• 2020

Cytoskeleton components in living cell bear large compressive force and are responsible in maintaining the cell shape. Actually these filaments are surrounded by viscoelastic media within the cell. This surrounding, viscoelastic media affects the buckling behavior of these filaments when external force is applied on these filaments by exerting continuous pressure in opposite directions to the incipient buckling of the filaments. In this article a mechanical model is applied to account the effects of this media on the buckling behavior of intermediate filaments network of cytoskeleton. The model immeasurably associates; filament's bending rigidity, adjacent system elasticity, and cytosol viscosity with buckling wavelength, buckling growth rate and buckling amplitude of the filaments.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.5
• /
• pp.63-68
• /
• 1999

In this paper, the correlation between the growth mechanism and the optical property in GaN films grown by low-pressure metalorganic chemical vapor deposition was characterized using room temperature cathodoluminescence spectroscopy. An intense near band-edge emission, 364nm, and deep-level emission, 550nm, were observed. The intensity of 364nm peak was increased with increasing the beam current. Also the peak position of 364nm emission was red-shifted and the intensity of 550nm peak was increased with increasing the accelerating voltage. It shows that the deep-level emission is strongly associated with crystalline defects in the GaN at early stage. The relationship between the microstructure and the deep level emission observed by scanning electron microscope images and cathodoluminescence spectra was carefully analyzed.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.9
• /
• pp.96-103
• /
• 1994

The GaAs epilayer was grown at low temperature (LT. 250.deg. C) by molecular beam epitaxy. The properties of the LTT GaAs, before and after Rapid Thermal Annealing(RTA), were analyzed by Reflection of High Energy Electron Diffraction (RHEED), Double Crystal X-ray(DCX), Raman spectroscopy, PL and Photo-Induced Current Transient Spectroscopy (PICTS). The LT GaAs before RTA, was analyzed by RHEED and DCX, with a result of an improved surface morphology under a relatively As-rich(As/Ga ratio :28) condition, and of an increased lattics parameter of 1.1 1.7% in comparison with a GaAs substrate. However DCX and Raman spectroscopy revealed that the expanded lattics parameter and the crystallinity of LT GaAs could be recovered after RTA. On the other hand, PL spectra indicated that LT GaAs after RTA showed low optical sensitivity unlike High Temperature(HT) GaAs, and that its surface morphology and crystallinity were corresponded with those of HT GaAs. Finally PICTS spectra proved the fact that low sensitivity of LT GaAs was due to the deep level defects (Ec-0.85eV) which were strogly formed by raising RTA temperature to 750.deg. C.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.9-10
• /
• 2005

We report on the fabrication and characterization of self- and artificially-controlled ZnO nanostructures have been investigated to establish nanostructure blocks for ZnO-based nanoscale device application. Systematic realization of self- and artificially-controlled ZnO nanostructures on $SiO_2/Si$ substrates was proposed and successfully demonstrated utilizing metalorganic chemical vapor deposition (MOCVD) in addition with a focused ion beam (FIB) technique. Widely well-aligned two-dimensional ZnO nanodot arrays ($4{\sim}10^4$ nanodots of 130-nm diameter and 9-nm height over $150{\sim}150{\mu}m^2$ with a period of 750 nm) have been realized by MOCVD on $SiO_2/Si$ substrates patterned by FIB. A low-magnification FIB nanopatterning mode allowed the periodical nanopatterning of the substrates over a large area in a short processing time. Ga atoms incorporated into the surface areas of FIB-patterned nanoholes during FIB engraving were found to play an important role in the artificial control of ZnO, resulting in the production of ZnO nanodot arrays on the FIB-nanopatterned areas. The nanodots evolved into dot clusters and rods with increasing MOCVD growth time.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.788-796
• /
• 1996

$TiO_2$ films prepared by RF magnetron sputtering, electron beam evaporation, ion assisted deposition (IAD) and sol-gel method are prepared on c-Si substrate and vitreous silica substrate respectively. From the transmission spectra of $TiO_2$ films on vitreous silica substrate in the spectral region from 190 nm to 900 nm, k($\lambda$) of $TiO_2$ is obtained. Using k($\lambda$) in the interband transition region the coefficients of the quantum mechanical dispersion relation of an amorphous $TiO_2$ and hence n($\lambda$) including the optically opaque region of above fundamental transition energy are obtained. The spectroscopic ellipsometry spectra of $TiO_2$ films in the spectral region of 1.5-5.0eV are model analyzed to get the film packing density variation versus i) substrate material, ii) film thickness and iii) film growth technique. The complex refractive index change of these $TiO_2$ films versus water condensation is also studied. Film micro-structures by SE modelling results are compared with those by atomic force microscopy images and X-ray diffraction data.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.378-380
• /
• 2009

$MgF_2$ is a current material for the optical applications in the UV and deep UV range. Process variables for manufacturing the $MgF_2$ thin film were established in order to clarify optimum conditions for growth of the thin film depending upon process conditions, and then by changing a number of vapor deposition conditions and substrate temperature, Annealing conditions variously, structural and Optical characteristics were measured. Thereby, optimum process variables were derived. Nevertheless, modern applications still require improvement of the optical and structural quality of the deposited layers. In the present work, the composition and microstructure of $MgF_2$ single layers grown on slide glass substrate by Electro beam Evaporator(KV-660) processes, were analyzed and compared. The surface Substrate temperature having an effect on the quality of the thin film was changed from $200[^{\circ}C]$ to $350[^{\circ}C]$ at intervals of $50[^{\circ}C]$. and annealing temperature an effect on the thin film was changed from $200[^{\circ}C]$ to $400[^{\circ}C]$ at intervals of $50[^{\circ}C]$. Physical properties of the thin film were investigated at various fabrication conditions substrate temperature, annealing and temperature, annealing time by XRD, FE-SEM.

• Transactions of Materials Processing
• /
• v.19 no.5
• /
• pp.277-282
• /
• 2010

Magnesium alloy has been known as lightweight material in automobile and electronic industry with aluminum alloy, titanium alloy and plastic material. Friction welding is useful to join various metals and nonferrous metals that are difficult to join by such as gas welding, resistance welding and electronic beam welding. In this study, friction joining was performed to investigate mechanical properties of Mg alloy with 20mm diameter solid bar. Also the optimal joining conditions for its application were determined on the basis of tensile test, and hardness survey. The joining parameters were chosen as heating pressure, heating time, upsetting pressure, and upsetting time. Heating and upsetting pressure were executed under the range of 10~40MPa and 20~80MPa, respectively. From the experimental results, optimal joining conditions were determined as follows; rotating speed=2000rpm, heating pressure=35MPa, upsetting pressure=70MPa, heating time=1sec, upsetting time=5sec. Also the hardness of jointed boundary showed as HV50 which was similar to that of base metal at the optimal condition, and it was supposed that zone of HAZ was 8mm. Finally two materials were strongly mixed at interface part to show a well-combined microstructure without particle growth or any defect.